Focal BUS 20 Handleiding

Focal Subwoofer BUS 20

Lees hieronder de 📖 handleiding in het Nederlandse voor Focal BUS 20 (17 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/17
Français page 7
THE FOCAL GUARANTEE ONLY APPLIES IF PAGE 8 IS
RETURNED US WITH IN TO 16 DAYS OF PURCHASE .
Due to constant technological advances, Focal reserves its right to modify specifications without notice. Images may not conform exactly to specific product.
Focal® is a trademark of Focal-JMlab® - BP 374 - 108, rue de l'Avenir - 42353 La Talaudière
cedex - France - Tel. (+33) 04 77 43 57 00 - Fax (+33) 04 77 43 57 04 - www.focal-fr.com
BUS 20 & BUS 25
U s e r M a n u a l
Thank you for choosing Focal. To get the best results from your speaker, please
ensure you follow these recommendations, and keep carefully this user manual
so that you can consult it later. If not followed correctly any fault observed may
not be covered by the guarantee.
2
BUS 20 & BUS 25
U s e r M a n u a l
Precautions
For the subwoofer to perform at its best, we recommend to use it in a location where temperature
doesn’t go below 5°C.
• The location must also be dry and well-ventilated.
• The supply voltage requirement is 12VDC (13.8VDC) with the negative connection grounded.
Please make sure that the characteristics of your vehicle correspond with this requirement
before connecting the equipment.
• For safe driving, we recommend that you operate your sound equipment at a listening level
that does not drown out traffic noise.
Warning!
The performance of the Bus 20 and Bus 25 (Bomba under seat) allows high sound pressure
levels to be generated. We remind you that sustained listening beyond 110dB SPL can
permanently and irreversibly damage your hearing.
We recommend that you adjust the level of your equipment correspondingly.
For safety reasons, it is essential that you securely fix the subwoofer enclosure in the boot
(make sure you do not drill through the petrol tank if you fix it with screws).
Supplied elements
• 1 remote control with 5m (16Ft) cable
• 1 user manual
• 4 fixing clamps
• 4 screws M4*20
• 4 screws M6*8
• 1 power supply kit that contains
5m (16Ft) cable for the remote 0.5 mm2 (20 AWG) (blue and white)
5m (16Ft) cable for high level input 4 x 0.5 mm2 (4 x 20 AWG) (grey)
5m (16Ft) cable for the battery 3.3 mm2 (12 AWG) (yellow)
1,40m (4,5Ft) cable for the ground 2 x 1.3 mm2 (2 x 16 AWG) (black)
1 10A fuse placed in the fuse box
Cable routing
The 12V supply cables should be passed down on one side of the vehicle and the signal cables
down the other. These cables must be suitably protected to avoid any damage to insulation,
especially when feeding the cable through from the engine compartment to the passenger
cabin.
3
BUS 20 & BUS 25
U s e r M a n u a l
Installation
We included a fixing kit to ensure the subwoofer remains securely mounted. Two types of
installation are possible.
In the trunk
1 - Rear seats must be positioned in their normal fixed position.
2 - Decide the best location possible that suits your automobile and space available. The best
and most secure location for optimum sound quality is behind the rear seats, in the trunk
floor.
3 - Ensure the area for subwoofer location is clean and tidy. Any loose objects must be
removed, as they could knock and damage the subwoofer.
4 - Once the location has been decided, mark the screw hole positions for the fixing
brackets.
5 - Drill holes of 2 mm for the 4 fixing brackets, at your defined locations.
6 - Fix the clamps to the subwoofer basket with the four screws M6*8 (the fixing clamps have
a mounting direction system).
7 - Position the subwoofer so that the holes correspond to the M4*20 supplied screws and fix it.
8 - Please make sure the subwoofer is tightly fixed.
Under a seat
1 - The seat must be positioned in its normal fixed position.
2 - Decide the best location possible that suits your automobile and space available, checking
that the enclosure doesn’t hamper the seat mobility.
3 - Ensure the area for subwoofer location is clean and tidy. Any loose objects must be
removed.
4 - Once the location has been decided, mark the screw hole positions for the fixing
brackets.
5 - Drill holes of 2 mm for the 4 fixing brackets, at your defined locations.
6 - Fix the clamps to the subwoofer basket with the four screws M6*8 (the fixing clamps have
a mounting direction system)
7 - Position the subwoofer so that the holes correspond to the M4*20 supplied screws and fix it.
8 - Please make sure the subwoofer is tightly fixed


Product specificaties

Merk: Focal
Categorie: Subwoofer
Model: BUS 20

Heb je hulp nodig?

Als je hulp nodig hebt met Focal BUS 20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Subwoofer Focal

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer