Fluke i430 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke i430 (7 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 200 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
PN 4426307 (4822 872 30932 – Rev.3)
December 2011, Rev.3, 9/15
© 2011-2015 Fluke Corporation. All rights
reserved. Specifications are subject to change
without notice. All product names are
trademarks of their respective companies.
i430-Flexi-TF-II
6000 A Flexible
AC Current Probe
Instructions
Introduction
The i430-Flexi-TF-II (the Probe or Product) is a flexible AC current probe
for use with the Fluke 430 series I and II Power Quality Analyzers and
other dedicated test tools. The i430-Flexi-TF-II is optimized for current
measurement on thick and hard to reach conductors. Check the user
documentation of your test tool for compatibility before you use this
current sensor.
Available versions are:
•i430-Flexi-TF-II 61 cm (24 inch)
•i430-Flexi-TFII-48 122 cm (48 inch)
Contacting Fluke
To contact Fluke, call one of the following telephone numbers:
•Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)
•Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)
•Canada: 1-800-36-FLUKE (1-800-363-5853)
•Europe: +31 402-675-200
•Japan: +81-3-6714-3114
•Singapore: +65-6799-5566
•Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit http://register.fluke.com.
To view, print, or download the latest manual supplement, visit
http://us.fluke.com/usen/support/manuals.
To locate an authorized service center, go to www.fluke.com.
Safety
Read this section carefully. It will familiarize you with the most important
safety instructions for handling the Product.
A Warning identifies hazardous conditions and procedures that are
dangerous to the user.
A Caution identifies conditions and procedures that can cause damage
to the Product or the equipment under test.
XW Warning
To prevent possible electrical shock, fire, or personal injury:
• Read all safety information before you use the Product.
• Carefully read all instructions.
• The Probe is only to be used and handled by qualified
personnel.
• Do not work alone.
• Always connect the Product to the test tool before it is installed
around a conductor.
• Use the Product only as specified, or the protection supplied by
the Product can be compromised.
• Comply with local and national safety codes. Use personal
protective equipment (approved rubber gloves, face protection,
and flame-resistant clothes) to prevent shock and arc blast
injury where hazardous live conductors are exposed.
• Limit operation to the specified measurement category, voltage,
or current ratings.
• De-energize the circuit or wear personal protective equipment in
compliance with local requirements before you apply or remove
the Product.
• Do not touch voltages >30 V ac, 42 V ac peak, or 60 V dc.
• Do not use the Product around explosive gas, vapor, or in damp
or wet environments.
• Do not use the Product if it operates incorrectly.
• Do not use a current measurement as an indication that a circuit
is safe to touch. A voltage measurement is necessary to know if
a circuit is hazardous.
• Do not use the Product if it is damaged.
• Disable the Product if it is damaged.
• Do not use the Product if it has damaged insulation,
exposed metal, or if the wear indicator is visible. Do not use
if the flexible jaw wear indicator shows wear indicated by a
contrasting color on the inner insulation. Examine the
output lead for damaged insulation, exposed metal, or wear
indication.
• Before each use, examine the Product. Look for cracks or
missing pieces of the clamp housing or output cable
insulation. Also look for loose or weakened components.
Carefully examine the insulation around the jaws.
• Do not exceed the Measurement Category (CAT) rating of
the lowest rated individual component of a Product, probe,
or accessory.
• High voltages and currents can be present in adjacent
circuits under test.
• Do not use the Product above its rated frequency.
• Use the Product only on insulated conductors. Use caution
around bare conductors or bus bars. Do not touch the
conductor.
Symbols
The table below is a list of the symbols used on the Probe and in the
instructions.
Symbol Description
W WARNING - RISK OF DANGER. Consult user
documentation.
X WARNING. HAZARDOUS VOLTAGE. Risk of
electric shock.
- Do not apply around or remove from uninsulated
hazardous live conductors without taking additional
protective measures.
T Double Insulated

Measurement Category II is applicable to test and
measuring circuits connected directly to utilization
points (socket outlets and similar points) of the low-
voltage MAINS installation.

Measurement Category III is applicable to test and
measuring circuits connected to the distribution part
of the building’s low-voltage MAINS installation.

Measurement Category IV is applicable to test and
measuring circuits connected at the source of the
building’s low-voltage MAINS installation.
P Conforms to European Union directives.
) Certified by CSA Group to North American safety
standards.
ï‚¡ Conforms to relevant Australian safety and EMC
standards.
~
This product complies with the WEEE Directive
marking requirements. The affixed label indicates
that you must not discard this electrical/electronic
product in domestic household waste. Product
Category: With reference to the equipment types in
the WEEE Directive Annex I, this product is classed
as category 9 "Monitoring and Control
Instrumentation" product. Do not dispose of this
product as unsorted municipal waste.


Product specificaties

Merk: Fluke
Categorie: Niet gecategoriseerd
Model: i430

Heb je hulp nodig?

Als je hulp nodig hebt met Fluke i430 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Fluke

Fluke

Fluke ii500 Handleiding

7 Oktober 2024
Fluke

Fluke iSee TC01A Handleiding

9 September 2024
Fluke

Fluke TiX885 Handleiding

7 December 2023
Fluke

Fluke TiX875 Handleiding

7 December 2023
Fluke

Fluke TiX880 Handleiding

7 December 2023
Fluke

Fluke TiX870 Handleiding

7 December 2023
Fluke

Fluke EI-162BN Handleiding

9 Augustus 2023
Fluke

Fluke CNX C3003 Handleiding

8 Augustus 2023
Fluke

Fluke 80i-2010s Handleiding

8 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd