Ferroli DOMIcondens F 28 Handleiding

Ferroli Ketel & boiler DOMIcondens F 28

Lees hieronder de 📖 handleiding in het Nederlandse voor Ferroli DOMIcondens F 28 (12 pagina's) in de categorie Ketel & boiler. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

6

cod. 3540S921 — 11/2009 (Rev. 00)

DOMIcond

DOMIcondDOMIcondens F

ens F

ens Fens F

INSTRUCTIONS FOR USE, INSTALLATION AND MAINTENANCE

700

400

196

85 115 200

330

DOMIcondens F

DOMIcondens FDOMIcondens F

2GB cod. 3540S921 - 11/2009 (Rev. 00)

1. GENERAL INSTRUCTIONS

• Carefully read the instructions contained in this instruction booklet.

• After boiler installation, inform the user regarding its operation and give him this manual, which is an integral

and essential part of the product and must be kept with care for future reference.

• Installation and maintenance must be carried out by professionally qualified personnel, according to current

regulations and the manufacturer's instructions. Do not carry out any operation on the sealed control parts.

• Incorrect installation or inadequate maintenance can result in damage or injury. The Manufacturer declines

any liability for damage due to errors in installation and use or failure to follow the instructions.

• Before carrying out any cleaning or maintenance operation, disconnect the unit from the power supply using

the system switch and/or the special cut-off devices.

• In case of a fault and/or poor operation, deactivate the unit and do not attempt to repair it or directly intervene.

Contact professionally qualified personnel. Repair/replacement of the products must only be carried out by

professionally qualified using original spare parts. Failure to comply with the above could affect the safety of

the unit.

• This unit must only be used for its intended purpose. Any other use is considered improper and therefore

dangerous.

• The packing materials are potentially hazardous and must not be left within the reach of children.

• The images given in this manual are a simplified representation of the product. In this representation there

may be slight and insignificant differences with respect to the product supplied.

2. OPERATING INSTRUCTIONS

2.1 Introduction

Dear Customer,

DOMIcondens F is a high-efficiency sealed chamber condensing heat generator for

heating and hot water production running on natural gas or LPG, and equipped with a

microprocessor control system.

2.2 Control panel

fig. 1 - Control panel

Key

1 = Domestic hot water temperature setting

3 = Heating system temperature setting

5 = Display

6 = Summer/Winter mode selection - Reset button

7 = Unit On/Off - Eco/Comfort mode selection button

9 = DHW mode

10 = Summer mode

11 = Temperature or faults

12 = Eco (Economy) mode

13 = Heating

15 = Burner On and actual power

16 = Clock prearrangement

Indication during operation

Heating

A heating demand (generated by the Room Thermostat or Remote Timer Control) is in-

dicated by flashing of the hot air above the radiator on the display.

Domestic hot water (DHW)

A DHW demand (generated by drawing domestic hot water) is indicated by flashing of

the hot water under the tap on the display.

2.3 Lighting and turning off

Connection to the power supply

• During the first 5 seconds the display shows the card software version.

• Open the gas cock ahead of the boiler.

• The boiler is now ready to operate automatically whenever hot water is drawn or in

case of a room thermostat demand.

Boiler lighting and shutdown

Press the on/off button (detail 7 - fig. 1) for 5 seconds.

fig. 2 - Turning the boiler off

When the boiler is turned off, the PCB is still powered. Domestic hot water and heating

are disabled. The antifreeze system remains activated. To relight the boiler, press the

on/off button (detail 7 fig. 1) again for 5 seconds.

fig. 3

The boiler will be immediately ready to operate whenever domestic hot water is drawn

or in case of a room thermostat demand.

BThe antifreeze system does not work when the power and/or gas to the unit are

turned off. To avoid damage caused by freezing during long idle periods in win-

ter, it is advisable to drain all water from the boiler, DHW circuit and system; or

drain just the DHW circuit and add a suitable antifreeze to the heating system,

complying with that prescribed in sec. 3.3.

2.4 Adjustments

Summer/Winter Switchover

Press the summer/winter button (detail 6 - fig. 1) for 2 seconds.

The display activates the Summer symbol (detail 10 - fig. 1): the boiler will only deliver

domestic hot water. The antifreeze system remains activated.

To deactivate the Summer mode, press the button (detail 6 - fig. 1)summer/winter

again for 2 seconds.

Heating temperature setting

Use the heating buttons (detail 3 - fig. 1) to adjust the temperature from a min. of 30°C

to a max. of 85°C; it is advisable not to operate the boiler below 45°C.

fig. 4

Hot water temperature adjustment

Use the DHW buttons (detail 1 - fig. 1) to adjust the temperature from a min. of 40°C to

a max. of 55°C.

fig. 5

Room temperature adjustment (with optional room thermostat)

Using the room thermostat, set the temperature required in the rooms. If the room ther-

mostat is not installed, the boiler will keep the system at the set system delivery setpoint

temperature.

Room temperature adjustment (with optional remote timer control)

Using the remote timer control, set the required temperature in the rooms. The boiler will

adjust the system water according to the required room temperature. For operation with

remote timer control, please refer to the relevant instruction manual.

ECO/COMFORT selection

The unit has a function that ensures a high domestic hot water delivery speed and max-

imum comfort for the user. When the device is activated (COMFORT mode), the water

contained in the boiler is kept hot, therefore ensuring immediate availability of hot water

on opening the tap, without waiting times.

The device can be deactivated by the user (ECO mode) by pressing the eco/comfort

button (detail 7 - fig. 1) with the boiler in standby mode. In ECO mode the display acti-

vates the ECO symbol (detail 12 - fig. 1). To activate COMFORT mode, press the eco/

comfort button (detail 7 - fig. 1) again.

Adjustments from Remote Timer Control

AIf the Remote Timer Control (optional) is connected to the boiler, the above ad-

justments are managed according to that given in table 1.

Table. 1

Water system pressure regulation

The filling pressure read on the boiler water gauge with the system cold must be approx

1.0 bar. If the system pressure falls to values below minimum, the boiler stops and fault

F37 is displayed.

eco

comfort

reset

9 15

3 6

Heating temperature setting

Adjustment can be made from the Remote Timer Control menu and the

boiler control panel.

Hot water temperature adjustment

Adjustment can be made from the Remote Timer Control menu and the

boiler control panel.

Summer/Winter Switchover

Summer mode has priority over a possible Remote Timer Control heat-

ing demand.

Eco/Comfort selection

Adjustment can only be made from the boiler control panel.

DOMIcondens

DOMIcondensDOMIcondens F

F F

cod. 3540S921 - 11/2009 (Rev. 00)

3. INSTALLATION

3.1 General Instructions

BThis unit must only be used for its intended purpose. This unit is designed to

heat water to a temperature below boiling point and must be connected to a

heating system and/or a water supply system for domestic use, compatible with

its performance, characteristics and its heating capacity. Any other use is

deemed improper.

BOILER INSTALLATION MUST ONLY BE CARRIED OUT BY QUALIFIED PERSON-

NEL, IN ACCORDANCE WITH ALL THE INSTRUCTIONS GIVEN IN THIS TECHNICAL

MANUAL, THE PROVISIONS OF CURRENT LAW, THE PRESCRIPTIONS OF THE

TECHNICAL STANDARDS (BS), ANY LOCAL REGULATIONS AND THE RULES OF

PROPER WORKMANSHIP.

Incorrect installation can cause damage or injury for which the manufacturer declines

any responsibility.

Installation of this unit must be carried out in strict compliance with the present

instructions and the following regulations applicable in Great Britain.

Gas Safety Regulations (Installations & Use).

Local Building Regulations..

The Building Regulations (Part L).

The Buildings Standards (Scotland - Consolidated) Regulations. British Standards

Codes of Practice (BSI):

Model Water By-Laws

For Northern Ireland, observe the current applicable regulations.

Safe handling of materials

Pay attention when handling the boiler insulation panels because the material they are

made of could irritate the skin. No part of the boiler contains asbestos, mercury or CFC's.

Advice for transport and handling

For lifting and transport always take suitable safety precautions: keep your back straight,

bend knees, do not turn your body, move feet, avoid bending forward or sideways and

keep the load as close as possible to your body.

If possible, use a trolley or other suitable means to carry the boiler.

Grip the boiler firmly and, before lifting it, try and find the point where the load is concen-

trated in order to establish the centre of gravity and suitably reposition yourself.

3.2 Place of installation

The combustion circuit is sealed with respect to the place of installation room, therefore

the unit can be installed in any room. However, the place of installation must be ade-

quately ventilated to prevent the creation of dangerous conditions in case of even small

gas leaks. This safety regulation is laid down by EEC Directive no. 90/396 for all gas

units, including those with sealed chamber.

The unit is suitable for operation in a partially protected place in conformity with EN 297/

A6, with minimum temperature -5°C. If equipped with the special antifreeze kit, it can be

used with minimum temperatures to -15°C. The boiler must be installed is a protected

place, e.g. under the slope of a roof, inside a balcony or in a sheltered recess.

The place of installation must in any case be free of dust, flammable materials or objects

or corrosive gases.

The boiler is arranged for wall mounting and comes standard with a hooking bracket. The

wall fixing must ensure a stable and effective support for the generator.

AIf the unit is enclosed in a cabinet or mounted alongside, a space must be pro-

vided for removing the casing and for normal maintenance operations

3.3 Plumbing connections

Important

The heating capacity of the unit must be previously established by calculating the build-

ing's heat requirement according to the current regulations. To ensure proper operation

and long boiler life, the plumbing system must be adequately sized and complete with all

the necessary accessories, including a room thermostat, a thermostattable valve (TRV)

etc. The system delivery and return pipes must have a diameter of at least 22 mm for the

first 3 m of length from the unit.

If the system delivery and return pipes follow a path where air pockets can form in certain

places, it is advisable to install vent valves at these points. Also, type "A" drain cocks

must be installed at the lowest points in the system to allow complete emptying.

BAn automatic bypass with flow rate of at least 6 l/min. must be installed (con-

nected as far away as possible from the boiler) if radiators with thermostatic

valves have been connected.

fig. 6 - Automatic bypass connection

The temperature drop between the delivery manifold and the return to the boiler should

not exceed 20°C.

BDo not use the water system pipes to earth electrical appliances.

Before installation, carefully wash all the pipes of the heating system to remove any re-

siduals or impurities that could affect proper operation of the unit (as required by BS 7593

Building regs Doc L).

Carry out the connections to the unit as indicated in fig. 7.

fig. 7 - Water connections

Shutoff valve kit

Make sure to install the shutoff valves (supplied) between the boiler and the heating sys-

tem, allowing the boiler to be isolated from the system if necessary.

BThe safety valve outlet must be connected to a copper pipe of 15 mm diameter

with continuous fall from the boiler to run off the system water in case of over-

pressure in the heating circuit. Otherwise, if the discharge valve cuts in and

floods the room, the boiler manufacturer cannot be held liable. The drain must

be run to the outside of the building to avoid the risk of damage or injury due to

the hot water in case of overpressure in the system.

Make the boiler connection in such a way that its internal pipes are free of stress. If a

non-return valve is installed also on the DHW circuit (if provided for), it is necessary to

install a safety valve between the boiler and the circuit (with the non-return valve at least

3 m from the boiler) or an expansion tank for domestic use.

For installation, follow the instructions contained in the kit.

B.S.

5440 Detail 1 Flues

B.S.

5440 Detail 2 Air supply and ventilation

B.S.

5449 ......... Systems for hot water production with forced circulation

B.S.

6798 ......... Installation of gas-fired boilers for hot water

B.S.

6891 ......... Gas systems

B.S.

7671 ......... IEE wiring system regulations

B.S.

4814 ......... Specifications for expansion tanks

B.S.

5482 ......... LPG systems

B.S.

7593 ......... Water treatment in central heating systems for domestic hot water production

B.S.

5546 ......... Installation of systems for domestic hot water production

B.S.

5955-8 ......... Installation of plastic pipes

Gas

Hot water

Additional expansion

vessel C.H. (if required)

Filling

point C.H.

Automatic

Bypass

Cold water mains

39 60 60 86 95 60

1 3

52 4

Product specificaties

Merk:	Ferroli
Categorie:	Ketel & boiler
Model:	DOMIcondens F 28

Heb je hulp nodig?

Als je hulp nodig hebt met Ferroli DOMIcondens F 28 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ketel & boiler Ferroli

Ferroli PREXTHERM RSW 1250N÷6000N Handleiding

5 November 2024

Ferroli Calypso Handleiding

18 Juni 2023

Ferroli DOMIcompact F 30 B Handleiding

29 Mei 2023

Ferroli Bravo SN 10 S Handleiding

20 Mei 2023

Ferroli Aqua1 Plus 260HT Handleiding

19 Mei 2023

Ferroli Aqua1 Plus 160HT Handleiding

16 Mei 2023

Ferroli DOMIcompact F 24 D Handleiding

21 April 2023

Ferroli Bravo SN 15 S Handleiding

19 April 2023

Ferroli B90 Comfort Handleiding

15 April 2023

Ferroli DOMIcondens F 24 Handleiding

14 April 2023

Handleiding Ketel & boiler

Nieuwste handleidingen voor Ketel & boiler

Sime MURELLE REVOLUTION 30 Handleiding

24 December 2024

Daikin EKHHE260PCV3 Handleiding

20 December 2024

Daikin EKHHE200CV3 Handleiding

20 December 2024

Daikin EKHHE200PCV3 Handleiding

20 December 2024

Daikin EKHTSU260AC Handleiding

20 December 2024

Daikin EKHTSU200AC Handleiding

20 December 2024

Daikin EKSR3PA Handleiding

20 December 2024

Daikin EKSRDS1A Handleiding

20 December 2024

Midea D80-20ED6 Handleiding

14 December 2024

Midea MWH-180ECNCR Handleiding

11 December 2024