Extech TG20 Handleiding

Extech Meetapparatuur TG20

Lees hieronder de 📖 handleiding in het Nederlandse voor Extech TG20 (3 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
User's Guide
Wire Tracer Probe and Transmitter
Model TG20
TG20-EU-EN-V1.0 03/12 2
Introduction
Congratulations on your purchase of Extech’s Model TG20. This tone generator and amplifier probe
set is used to quickly trace and identify cables or wires within a group and also check the operation of
phone lines. With proper use and care, this meter will provide many years of reliable service.
Meter Description
1. Modular connector
2. Test leads
3. Function LEDs
4. Power switch
5. Probe tip
6. Power/Sensitivity control
Operating Instructions
Note: To extend battery life, remember to turn off the probe and transmitter after tracing the cables
Self Check
1. Turn the probe on and set the transmitter to TONE.
2. The RED LED on both units will light up. Replace the batteries if they do not.
3. Touch the probe to the transmitter wires and check for the generated tone..
Cable/Wire tracing
CAUTION: Do not connect the transmitter to any wire or cable with an active circuit of more than
24VAC.
1. Connect the transmitter to the cable
a) For cables terminated at one end, connect the red alligator clip to a wire and the black
alligator clip to equipment ground
b) For un-terminated cables, connect the red alligator clip to one wire and the black alligator
clip to another wire.
c) For cables with modular connectors, insert the RJ11 plug directly into the connector.
2. Set the transmitter power switch to the TONE position. The red TONE LED will turn on.
3. On the probe, rotate the Power/Sensitivity control so that the POWER LED is on..
4. Hold the insulated probe tip against the wire in question to pick up the signal generated by the
transmitter.
5. Rotate the volume/sensitivity control on the probe for the appropriate level and sensitivity to
identify and trace the wire.
6. The tone will be the loudest on the wires connected to the tone generator.
Continuity testing
CAUTION: Disconnect power and loads from any circuits to be tested.
4. Connect the test leads to the wire under test.
5. Switch the transmitter to the CONTINUITY position.
6. The CONTINUITY LED will glow GREEN for if the resistance is less than 10,000 ohms. The
LED intensity will be very bright for very low resistances and will decrease in intensity as
resistance increases.
1
2
3
4
5
6
TG20-EU-EN-V1.0 03/12 3
Identifying telephone cable Tip and Ring – Using Alligator Clips
1. Switch the transmitter to the OFF position
2. Connect the BLACK clip to ground
3. Connect the RED clip to a line.
4. The LED color identifies the line.
5. GREEN indicates the Ring line, RED indicates the Tip line.
6. If both RED and GREEN light up, AC voltage is present (do not exceed 24V)
Identifying telephone cable Line Condition
1. Switch the transmitter to the OFF position
2. Plug the connector into the phone line or connect the RED clip to the RING line and the
BLACK clip to the TIP line.
3. The LED color identifies the line condition.
a. GREEN indicates a clear line.
b. RED indicates a busy line.
c. Green with a flashing RED indicates a ringing line.
Battery replacement
Open the battery cover and replace the battery as needed.
You, as the end user, are legally bound ( ) to return all used batteries Battery ordinance
and accumulators; disposal in the household garbage is prohibited!
You can hand over your used batteries / accumulators at collection points in your
community or wherever batteries / accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the
end of its lifecycle
Specifications
Power 9V battery (1 for transmitter and 1 for probe))
Dimensions Probe - 8.7x2x1.3" (220x50x32mm)
Transmitter - 2.6x2.7x1.1" (65x68x28mm)
Weight Probe 3.2oz (91g);
Transmitter3.2oz (91g)
Copyright © 2012 Extech Instruments Corporation (a FLIR company)
All rights reserved including the right of reproduction in whole or in part in any form.
www.extech.com

Product specificaties

Merk: Extech
Categorie: Meetapparatuur
Model: TG20

Heb je hulp nodig?

Als je hulp nodig hebt met Extech TG20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Meetapparatuur Extech

Extech

Extech 380926 Handleiding

22 Oktober 2024
Extech

Extech 380941 Handleiding

22 Oktober 2024
Extech

Extech PRC20 Handleiding

21 Augustus 2024
Extech

Extech PRC30 Handleiding

21 Augustus 2024
Extech

Extech SD900 Handleiding

21 Augustus 2024
Extech

Extech PRC15 Handleiding

21 Augustus 2024
Extech

Extech 412300A Handleiding

21 Augustus 2024
Extech

Extech 412400 Handleiding

21 Augustus 2024
Extech

Extech 433201A Handleiding

21 Augustus 2024
Extech

Extech SD910 Handleiding

21 Augustus 2024

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

PCE Instruments

PCE Instruments PCE-LOC 10 Handleiding

3 December 2024
PCE Instruments

PCE Instruments PCE-HVAC 6 Handleiding

3 December 2024
PCE

PCE -IVE 320 Handleiding

3 December 2024
PCE

PCE -IVE 330 Handleiding

3 December 2024
PCE Instruments

PCE Instruments PCE-VE 260HT Handleiding

3 December 2024
Kern

Kern ORA 1WB Handleiding

30 November 2024
Uni-T

Uni-T UT383s Handleiding

30 November 2024
Uni-T

Uni-T UT363s Handleiding

30 November 2024
Uni-T

Uni-T UT18D Handleiding

30 November 2024
Kogan

Kogan KASMSRTHZ1A Handleiding

25 November 2024