Extech IR200 Handleiding
Extech
Multimeter
IR200
Lees hieronder de 📖 handleiding in het Nederlandse voor Extech IR200 (7 pagina's) in de categorie Multimeter. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/7
User Manual
InfraRed Thermometer
with Laser Pointer
MODEL IR400
Additional User Manual translations available at www.extech.com
IR400 en 2.0- - vUS_ 7/22
2
Introduction
Congratulations on your purchase of the Model IR400 IR Thermometer. The IR400 is capable of
non-contact (infrared) temperature measurements at the touch of a button. The built-in laser pointer
increases target accuracy while the backlit LCD and handy pushbuttons combine for convenient,
ergonomic operation. This meter is shipped fully tested and calibrated and, with proper use, will
provide years of reliable service.
Safety
• Use extreme caution when the laser beam is onpointer
• Do not point the beam toward anyone's eye or allow the beam
to strike the eye from a reflective surface
• Do not use the laser near explosive gases or in other
potentially explosive areas
Meter Description
Meter Description
1. Laser pointer beam
2. IR Sensor
3. Measurement Trigger
4. Battery Compartment
5. LCD Display
6. Pushbuttons
7. Handle Grip
Display Description
1. Temperature scan in progress (trigger held)
2. Last reading held (trigger released)
3. Laser pointer ON
4. Emissivity (0.95 fixed)
5. Max or MIN value displayed
6. Temperature display
7. Low battery icon (replace battery)
8. Temperature units
IR400 en 2.0- - vUS_ 7/22
3
Operating Instructions
Basic IR Measurements
1. Hold the meter by its handle and point it toward the surface to be measured.
2. Pull and hold the trigger to turn the meter on and begin testing. The temperature reading, the
flashi and ng ‘SCAN’ icon the unit of measure, , € = 0.95 will appear.
3. seconds Release the Trigger and the reading will hold for approximately 10 (HOLD will appear
on the LCD) after which the meter will automatically shut off.
Laser Pointer
1. When the trigger is pressed, the laser pointer will turn on and identify the spot being measured.
The icon on the display indicates that the pointer is on.
2. To turn the laser pointer off, press the button while scanning. Press the button again to
turn the pointer back on.
MAX - MIN
The Max / Min feature provides a means to display the highest (MAX) or lowest (MIN) temperature
measured during a scan.
1. While the trigger is pressed, press the MAX/MIN button will appear. The “MAX” icon and the
maximum measured temperature will appear in the display. The displayed temperature will not
change until a higher temperature is measured.
2. Press the MAX/MIN button again and the “ ” icon will appear. MIN The minimum temperature
only be displayewill d
3. Press the MAX/MIN button again to return to a real time display.
Temperature Units C/F
To change the temperature units, press and release the trigger. Momentarily press the C/F button
and the temperature unit will change.
Backlight
When the meter is on, press the backlight button to turn the backlight on. Press the button again
to turn the backlight off.
Note: Constant use of the backlight feature will reduce battery life.
Over-Range Indication
If the temperature measurement exceeds the specified temperature range, the thermometer will
display “HI” or “LO” in place of a temperature reading.
Product specificaties
| Merk: | Extech |
| Categorie: | Multimeter |
| Model: | IR200 |
Heb je hulp nodig?
Als je hulp nodig hebt met Extech IR200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Multimeter Extech
27 November 2023
27 November 2023
27 November 2023
27 November 2023
10 Juni 2023
10 Juni 2023
10 Juni 2023
10 Juni 2023
7 Juni 2023
7 Juni 2023
Handleiding Multimeter
- Multimeter Abus
- Multimeter Aldi
- Multimeter Alecto
- Multimeter Altai
- Multimeter Amiko
- Multimeter Amprobe
- Multimeter Appa
- Multimeter Basetech
- Multimeter Beha-Amprobe
- Multimeter Benning
- Multimeter Brandson
- Multimeter Brennenstuhl
- Multimeter Bruder Mannesmann
- Multimeter Digitus
- Multimeter Elma
- Multimeter Elro
- Multimeter Ferm
- Multimeter Flir
- Multimeter Fluke
- Multimeter Gembird
- Multimeter Gossen Metrawatt
- Multimeter Greenlee
- Multimeter Hager
- Multimeter Hubinont
- Multimeter Ideal
- Multimeter Keithley
- Multimeter Kingcraft
- Multimeter Laserliner
- Multimeter Mastech
- Multimeter Maxwell
- Multimeter Megger
- Multimeter Metrel
- Multimeter Metrix
- Multimeter Micronta
- Multimeter Milwaukee
- Multimeter Monacor
- Multimeter Parkside
- Multimeter PCE Instruments
- Multimeter Perel
- Multimeter Plieger
- Multimeter Powerfix
- Multimeter Profile
- Multimeter Sanwa
- Multimeter Schneider
- Multimeter Silverline
- Multimeter Skandia
- Multimeter Stanley
- Multimeter TFA
- Multimeter Topcraft
- Multimeter Uni-T
- Multimeter Velleman
- Multimeter Voltcraft
- Multimeter Wiha
- Multimeter Workzone
- Multimeter Joy-it
- Multimeter Jung
- Multimeter Clas Ohlson
- Multimeter Steren
- Multimeter Klein Tools
- Multimeter EMOS
- Multimeter Tacklife
- Multimeter Biltema
- Multimeter REV
- Multimeter Etekcity
- Multimeter Testo
- Multimeter Somogyi
- Multimeter Testboy
- Multimeter Yato
- Multimeter Wago
- Multimeter GW Instek
- Multimeter Kyoritsu
- Multimeter Owon
- Multimeter Projecta
- Multimeter Cablexpert
- Multimeter Högert
- Multimeter Multimetrix
- Multimeter Digi-tool
- Multimeter Kewtech
- Multimeter Sonel
- Multimeter Testec
- Multimeter Vimar
- Multimeter Strex
- Multimeter PeakTech
- Multimeter MBS
- Multimeter MGL Avionics
- Multimeter Rigol
- Multimeter Chauvin Arnoux
- Multimeter Aim TTi
- Multimeter CEM
- Multimeter Horex
- Multimeter Cosinus
- Multimeter Kurth Electronic
- Multimeter Weltron
- Multimeter Rohde & Schwarz
- Multimeter EEVBlog
- Multimeter Weidmüller
- Multimeter HT Instruments
- Multimeter Caltek
- Multimeter Elworks
- Multimeter Qian
- Multimeter Bearware
- Multimeter Noyafa
Nieuwste handleidingen voor Multimeter
17 November 2024
14 November 2024
11 November 2024
22 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
30 September 2024