Extech 445814 Handleiding

Extech Meetapparatuur 445814

Lees hieronder de 📖 handleiding in het Nederlandse voor Extech 445814 (1 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

User’s Guide

Model 445814 Humidity Alert

Humidity Indicator with Dew Point and Programmable Hi/Lo %RH Alarms

Introduction

Congratulations on your purchase of Extech’s Humidity Alert Hygro-Thermometer.

Humidity alarms warn when the %RH exceeds a pre-set HI or LO limit. It also

features Humidity and Temperature calibration adjustments. The unit can be wall-

mounted or placed on a flat surface using the fold-out stand. This professional

meter, with proper care, will provide years of safe reliable service.

Meter Description

1. Temperature-Humidity Sensor

2. %RH Display

3. Dew Point Display

4. Temperature Display

5. %RH LED alarm

6. Max/Min push button

7. Reset push button

8. Audible Alarm ON/Off switch

9. Tilt Stand

10. Humidity calibration adjust

11. Temperature units switch (ºF/ºC)

12. Temperature calibration adjust

13. Wall hanger

14. Battery compartment

Cautions

This device is not a toy and must not reach children’s hands. It contains

hazardous objects as well as small parts that the children could swallow. In

case a child swallows any of them, please contact a physician immediately

Do not leave batteries and packing material lying around unattended; they

can be dangerous for children if they use them as toys

In case the device is going to be unused for an extended period of time,

remove the batteries to prevent them from training

Expired or damaged batteries can cause cauterization on contact with the

skin. Always, therefore, use suitable hand gloves in such cases

See that the batteries are not short-circuited. Do not throw batteries into the

fire.

the right of reproduction in whole or in part in any form.

www.extech.com

V3.1 10/05

Operation

Preparation for use

Open the battery compartment by pushing the cover on the rear of the

instrument downward as indicated by the arrow. Remove the battery insulating

strip and the protective film cover on the LCD display.

Temperature Units

Select ºF or ºC units using the rear selection switch.

Audible alarm

Select or using the rear selection switch to turn the audible alarm on or

off.

Maximum / Minimum display

1. Press the MAX/MIN button. The highest value measured since the Reset

button was last pressed appears on the display.

2. Press the MAX/MIN button again to display the lowest value measured since

the Reset button was last pressed.

3. Press the MAX/MIN button again to return to normal display operation.

Resetting (clearing) the MAX/MIN memory

1. Press the MAX/MIN button to enter the MAX/MIN mode.

2. Press and hold the RESET button for 1 second to clear the memory and

start recording new max/min values.

Setting the %RH Alarm Limits.

1. Simultaneously Press and HOLD the MAX/MIN and RESET button until “HI”

and the stored HI %RH limit appears flashing.

2. Press the RESET button to set the Hi %RH limit. Hold the button in for rapid

adjustment.

3. Press the Max/Min button. “LO” and the stored LO %RH limit will appear

flashing

4. Press the RESET button to set the LO %RH limit.

5. Press the Max/Min button to turn on or off the alarm. The alarm icon will

appear in the display when the alarm is active.

6. Press and hold the RESET button to save the settings and exit the mode.

Alert

If %RH exceeds the HI limit or goes below the LO limit the alert will be

activated. The alert consist of two flashing ‘ALERT” icons in the upper display,

a flashing red light (for 60 seconds) and an audible buzzer (for 60 seconds)

Calibration

RH Calibration

1. Insert meter’s sensor into a humidity chamber. The reference should be >70%

RH.

2. Check the reading after 1 hour.

3. Adjust the RH calibration pot in ½ turn increments, waiting for the display to

update after each adjustment, until the reading is within the accuracy

specification.

Temperature Calibration

1. Place the sensor in a stabilized environment of approximately 21°C.

2. Check the reading after 1 hour.

3. Adjust the temperature calibration pot in ½ turn increments, waiting for the

display to update after each adjustment, until the reading is within the

accuracy specification.

Battery Replacement

Open the battery compartment by sliding the battery cover on the rear of the

instrument downward as indicated by the arrow. Replace the 1.5V ‘AA’ batteries

and replace the cover.

You, as the end user, are legally bound (Battery ordinance) to

return all used batteries and accumulators; disposal in the

household garbage is prohibited!

You can hand over your used batteries / accumulators,

gratuitously, at the collection points for our branches in your

community or wherever batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the

disposal of the device at the end of its lifecycle

Specications

Range Accuracy

Temperature -10 to 60

14 to 140

+ 1.0oC within -10oC to 50oC

+ 1.8oF within 14oF to 122oF

Humidity 10% to 99% +

4% RH within 25% to 85% RH and 0 to

50oC or 32 to 122oF

Dew Point -36 to 60

-32.8 to 140

+/-2oC. @ 20

+/-3.6oF @ 68oF

Battery (2) 1.5V 'AAA' cell

Weight 6 oz (169g)

Dimensions Display: 4.3x3.9x0.8” (109x99x20mm)

Note: If subjected to an electrostatic discharge the meter may

malfunction and require the user to perform a reset.

Product specificaties

Merk:	Extech
Categorie:	Meetapparatuur
Model:	445814

Heb je hulp nodig?

Als je hulp nodig hebt met Extech 445814 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Meetapparatuur Extech

Extech 380926 Handleiding

22 Oktober 2024

Extech 380941 Handleiding

22 Oktober 2024

Extech PRC20 Handleiding

21 Augustus 2024

Extech PRC30 Handleiding

21 Augustus 2024

Extech SD900 Handleiding

21 Augustus 2024

Extech PRC15 Handleiding

21 Augustus 2024

Extech 412300A Handleiding

21 Augustus 2024

Extech 412400 Handleiding

21 Augustus 2024

Extech 433201A Handleiding

21 Augustus 2024

Extech SD910 Handleiding

21 Augustus 2024

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

TFA 40.1001 Handleiding

21 December 2024

Ansmann Comfort Check Handleiding

20 December 2024

PCE Instruments PCE-PST 1 X Handleiding

16 December 2024

Steinberg SBS-LF-147 Handleiding

15 December 2024

Steinberg SBS-SM-135C Handleiding

15 December 2024

Steinberg SBS-MT-100 Handleiding

15 December 2024

Steinberg SBS-SM-130C Handleiding

15 December 2024

Steinberg SBS-DT-999 Handleiding

15 December 2024

Steinberg SBS-DL-123D Handleiding

15 December 2024

Steinberg SBS-LF-141 Handleiding

15 December 2024