Elica Vavano EVV636S1 Handleiding

Elica Afzuigkap Vavano EVV636S1

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Elica Vavano EVV636S1 (10 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
Use, Care, and
Installation Guide
Guide
dā€™utilisation,
dā€™entretien et
dā€™installation
GuĆ­a de
instalaciĆ³n, uso y
mantenimiento
READ AND SAVE THESE
INSTRUCTIONS
LISEZ CES
INSTRUCTIONS ET
CONSERVEZ-LES
LEA Y CONSERVE
ESTAS INSTRUCCIONES
LIB0152213
Printed in Mexico
10/18
Models: KIT0154387
7
3 For or EVV648S1, EVV636S1 range hood models
you have to remove the spacer and the dip trays before
removing the internal motor blower.
A
BA. Drip trays screws
B. Drip trays
AB
A. Spacer screws
B. Spacer
4 Remove the range hood internal motor blower.
B
A
A. Blower
B. Blower screws
5 Install the rectangular brackets (included in kit) with
screws (4)4.2x8 mm.
6 Install the spacer, dip trays and grease ļ¬lters.
B
A
A. Rectangular brackets
B. Screws
B. For dual Blower Motor Models (ECL136S4, ECL142S4,
ECL148S4, ELI142S2, ELI136S2, ETR134S1, EAR140S4,
EAR146S4, EAR134S4, ELN136S2, ELN142S2, ELN148S1)
1 Remove the ļ¬lters, the mounting screws and lock washers.
A
B
A. Screw with locker
washer
B. Mounting Hole
2 For ELN136S2, ELN142S2, ELI136S2, ELI142S2,
EAR134S4 range hood models you have to remove
the blower mounting screws from the top of the hood
housing.
A. Blower screws
A
8
3 Remove the motor mounting plate by setting free the
spring clip. NOTE: The spring clip should be outside the
slot in the mounting plate.
A. Mounting plate
B. Spring Clip
A
B
A. Mounting plate
B. Spring Clip
A
B
4 Run out the power supply wires and connector through
the hole in the right end of the motor mounting plate.
5 Slide out the left mounting plate from under the motor
mounting bracket.
A
B
A. Motor mounting plate
B. Motor mounting bracket
6 Install the grease ļ¬lters.
Prepare for Mounting the In-Line Blower System
The In-Line Blower System must be fastened to a secure
structure of the roof, ceiling, wall, ļ¬‚oor, or new or existing
frame construction. The 4 holes on either the inlet (bottom)
side or the outlet (top) side of the blower must be used to
mount the in-line blower system to the structure.
NOTE: The mounting hole locations must span the studs.
Additional stud framing may be required. Plywood may be
used to span open areas between ceiling joists or roof rafters
to aid installation. This structure must be strong enough to
support the weight of the in-line blower system (50 lb [22.6
kg] min).
Prepare the In-line Blower System
I WARNING
Excessive Weight Hazard
Use two or more people to move and install range hood.
Failure to do so can result in back or other injury.
1 Disconnect power.
2 Determine which venting method to use: roof or wall
exhaust.
3 Using two or more people, move the in-line blower motor
system to the mounting location.
4 Remove the 10 screws from the front cover of the in-line
blower motor housing and set them aside.
5 Remove the front cover of the in-line blower motor
housing and set it aside.
NOTE: To make the in-line blower motor housing easier to
mount, the blower motor assembly can be removed.
6 Disconnect the motor electrical plug from the blower
motor assembly.
7 Remove the screws that secure the blower motor
assembly to the in-line blower housing and set them aside.
8 Pull the spring clip to release the blower motor assembly.
Remove the blower motor assembly from the housing and
place it on a covered surface.
A
BC
D
A. Front cover
B. Blower mounting
screws
C. Spring clip
D. Motor electrical
plug


Product specificaties

Merk: Elica
Categorie: Afzuigkap
Model: Vavano EVV636S1

Heb je hulp nodig?

Als je hulp nodig hebt met Elica Vavano EVV636S1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afzuigkap Elica

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap