Electrolux EWE361MB-DST1 Handleiding

Electrolux Ketel & boiler EWE361MB-DST1

Lees hieronder de 📖 handleiding in het Nederlandse voor Electrolux EWE361MB-DST1 (2 pagina's) in de categorie Ketel & boiler. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

EN ELECTRIC WATER HEATER USER MANUAL

EWE241MX-DST2

EWE381MX1DST2

EWE451MX-DST2

EWE451MB-DST2

EWE481MX1DST2

1. PARTS IDENTIFICATION (NORMAL SHOWER MODEL)

1. Front Cover

2. Main Display

(*LED Display Main PCB

Board behind front cover)

3. 3 in 1 Stop Valve

i) Stop Valve

ii) Flow Regulator Valve

iii) Built-in-Filter

4. Mesh Filter

5. Rail Support

6. Handshower

7. Adjustable Shower Holder

8. PVC Hose

9. Soap Tray

10. Slider Rail

11. Terminal Block

12. Thermostat (Double-Action)

13. Heater Tank

14. PCB Board (Test & Reset)

15. ELCB Board

16. Water Outlet Connection

17. SMPS PCB Board*

18. DC Pump*

19. Heater Base

20. Triac

21. Flow Sensor

22. Water Inlet Connection

23. Rating Label

24. Test & Reset Button

25. Logo Light

Fig 1. (Thailand, Indonesia, Philippines & Vietnam model)

Note : (*) For DC PUMP

No Pump model DC Pump model*

24 23

2. DESCRIPTION OF LCD DISPLAY AND CONTROL PANEL

1. Earth Icon

2. Power Display Bar

3. Temperature Indicator

4. Memory Indicator

5. Litre for EcoShower

6. rMemo y Button

7. Temperature (-) Button

8. Temperature (+) Button

9. Overheat Icon

10. ELCB Icon

11. Thermistor Icon

12. Low Water Pressure Indicator

13. Cold Shower Icon

14. EcoShower Counter

15. Pump Indicator

16. Cold Shower Button

Notes:

1. Memory includes temperature.

2. Buttons are 100% lit when unit is ON and buttons are not lit when unit is OFF or standby mode.

3. The display and buttons should not blink, unless there is an urgent message/ error/ alarm.

While normal operation all interactions shown without the screen segments blinking.

Fig. 1a

3. SAFETY INFORMATION

3.1 Products manufactured by Elect ux are safe rol

provided they are installed, used and maintained in

instructions and reco dations. Always refer mmen

to this manual if you have any doubt.

WARNING !

3.2 EARTHING :

A) The Eart ng inst lation ld be c ed out in hi al shou arri

acc ance with the al W ng lations.ord loc iri Regu

B) The Electric Water Heater must be earthed.

I er ng such as Earth c uctor not mprop groundi ond

ground ined (float g) or having gh isthi res ance to

grou ound c ld cause malfunction to ELCB and

electrical shock. Never use water heater if t re is he

do hiubt on Eart ng inst lation. al

good working order in accordance with our

3.3 If any of the following conditions occur as

contact the Elect ux Cust er S vice Call Centre. rol om er

Never attempt to ir the unit elf : repa yours

If the Electric Water Heater begins to make an

odd noise,smell or smoke.

If ELCB trips and LCD display does not light up.

Water temperature cannot be controlled.

If the Electric Water Heater shows signs of a

distinct change in performance.

If water leaks from inside.

s wn below, immediately switch off the mains and ho

3.5 For Pump el, it is ly re Mod high c ed ommend

to c nect the Water Inlet nection to st ge on Con ora

water tank , ot wise it may cause ge to the her dama

built in Pump Motor inside.

3.6 When the Shower is ed by someone such us

as child, derly rson, sick rson and physically el pe pe

han pedicapped rson, the rson concerned is pe

dly rkin equested to pay attention and check the

shower temperature by hand from time to time.

User is advised to test and just the waterad

tem rature bepe fore using.

3.7 During taking shower , once stop for a while

for washing with soap or shampoo and resuming

the shower again by turning on 3 in 1 stop valve

or water tap, it is normal that the instant water

temperature output from the water heater will be

higher than the set temperature.To avoid the risk

of scalding, it is advisable to avoid shower with

water output in that period, or let the water flow

for few seconds before continuing bathing.

3.8 During lightning/thunder, switch off the electric

supply to the shower unit in advance to protect the

shower unit against pos ble damage.si

NOTE : When removing the unit from package,

a small amount of ense water may be f nd cond ou

inside. This is normal as the unit is tested during

3.10 Installation must be carried out by a

quali ed personnel and in compliance local ﬁ

CAUTION !

manufacturing process.

authority regulations.

For the correct size of wire conductor

corresponding to different electrical l gs, oadin

please refer to T le 1. ab

This Electric Water Heater operates

at a minimum water ow rate of 2.0 litre/min ﬂ

and maximum working pressure of 6 bars.

For direct connection from the st ge water ora

tank, the Electric Water Heater must have an

installation minimum ght 1.0m below the hei

st ge water tank. ora

The built-in ELCB ll automat lwi ical y cut

o the er supply in case there is a current ff pow

leakage over 15mA rds.upwa

The thermostat will automatically cut off

the power supply if it has sensed an abnormal

rise in water tem rature. pe

The Electric Water Heater will not

function if there is insuf cient water ow ﬁ ﬂ

(min 2.0 liters/min) to trigger the ﬂow s sor. en

3.12

3.13

3.15

3.16

3.14

his Electric Water Heater must be

permanently ected to the direct main conn line

supply.

B) Recommended to install a er switch for pow

easily to switch ON & OFF the er ly to pow supp

electric water heater before and after use.

C) Hous ld ns switch box must have a eho mai

working ELCB (Incoming ns er smai pow upply)

with RCD es ue ent e) of 10mA.(r id curr devic

3.11 A) T

3.9 WARNING :

A) Metallic / chromed hose and conductive

control valve shall not be used.

B) Must use 3 in 1 Stop Valve accessories

provided with the electric water heater.

ELECTRIC WATER HEATER UNIT INSTALLATION

5.1 Select a suitable position in the bathroom.

5.2 Remove the screw (A) at the bottom of the unit. (Fig. 2)

5.3 Remove the Front Cover by lifting up the front cover from the bottom and be careful not to

over pull

5.4 Mark 3 Screw points of the Heater Base on the wall. The Heater Base position should be

1.5m above the bathroom floor and the left side should be at least 80mm from side wall.

The purpose for user easily to press Test & Reset button by themsleve regularly. (Fig.2)

5.5 Select a suitable position for the Shower Set then mark 4 screws point (2 on top and 2 on

bottom). The gap of 2 screw hole was 38mm. It is recommended that the top of the portion is in

level with the top of Electric Water Heater. (Fig. 3)

5.6 Use 6mm diameter drill and make the wall plug holes in depth of 34mm.

5.7 Insert the wall plugs and mount the Electric Water Heater firmly in position with the screws

provided.

5.8 Insert the Shower Holder and Soap Tray into the Slider Rail.

5.9 Mount the Slider Rail to the Rail Bracket .

5.10 Remove the cap from the Rail Bracket (Fig. 3A) and screw the Bracket to marked

position. Replace the cap. (Fig. 3)

the wire connected between the users interface and main control PCB. Next step is

4. ELECTRICAL LOADING TABLE

Voltage Power Current

(AC) (kW) (A)

220V ~

50/60 Hz

Conductor Size (csa)

mm Conduit Cable Flexible Cable

On/ Off Fuse /

Switch (A) MCB (A)

2.4 10.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

3.8 17.3 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

4.5 20.5 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

4.8 21.8 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

TABLE 1

disconnect wire from main PCB.

Fig. 3

connect the

hand shower

to flexible hose

Washer

connect to

water outlet

connection

ELECTRIC WATER HEATER

UNIT INSTALLATION DIAGRAM

285.5mm

SHOWER SET INSTALLATION DIAGRAM

Flexible Angle

Adjustment

Fig. 2

* Optional For AC/DC Pump

Screw

5 Spray

Patterns

Selection

Hand

Shower

Flexible

Hose

Soap Tray

Slider Rail Bar

Adjustable

Shower

Holder

Screw

Wall Plug

Mounting

Terminal

150 mm

connect to

water outlet

connection

3 in 1

stop valve

inlet

connect to

water inlet

connection

Wall

Min.

80 mm

Rail bracket cap

Hexagon tool

(Tighten plastic nut before close cap)

Plastic nut

Fig 3A

RAIL BRACKET COVER & CAP DISMANTLE STEPS

RAIL BRACKET

OPEN THE RAIL

BRACKET COVER

BY TURNING ANTI

CLOCKWISE &

USING SCREW

DRIVER TO OPEN

THE CAP

RAIL BRACKET

COVER COME-OUT

Check the position of the Shower Holder Ring.

this side up

Ensure the Shower Holder Ring are insert correctly.

Adjust to your desired position.

Push it until the Shower Holder Ring are fully

insert to the soap tray.

Adjust the Soap Tray until it fit nicely on the

Shower Holder Ring .

The gap of Shower Holder Ring must faced

inside the hook of the Soap Tray .

gap

Method of install the soap tray (straight bar type)

ELECTRICAL INSTALLATION

8.2 Remember to SWITCH OFF the

mains before carrying out any electrical

work.

8.3 Refer to TABLE 1 for the correct

cable size.

8.4 Use double insulation cable of over

2.5mm² for 2.4kW, 3.8kW, 4.5kW,

4.8kW models and 4.0mm² for 3.6.kW.

WARNING! PROCEDURE :

8.6 Insert the ll ed le t wa embedd cab hrough

Side Entry ‘A’ by cutting a le at the urce ho so

co rubb holdrd er er and ad the c le to le le ab Cab

Bracket ‘B’. (Fig. 6)

Fig. 6a

8.1 EARTHING :

A) The Eart ng inst lation shi al hould be

c ed out in acc ance with the local arri ord

W ng lat ns.iri Regu io

B) The Electric Water Heater must be

earthed. I er ng such as Earth mprop groundi

c ductor not on ground ined (float g) or having

high resistance to nd c ld cause grou ou

malfunction to ELCB and electrical shock.

Never use water heater if t re is ubt on he do

Eart ng insthi allation.

8.5 Lead the power cable from MCB to a

“ON/OFF’’double pole Linked Switch having

a contact separation of at least 3mm in all

poles outside the bathroom, then lead a

cable to the terminal block inside the Electric

Water Heater Unit. (Fig. 4)

Note: Refer to No. 3 Safety Information

before Plumbing and Electrical Installation

for safety and warning details.

NOTE:

Refer to TABLE 1 for electrical loading and

correct size of wire conductor

Fuse Distributor Board

Miniature Circuit Breaker (MCB)

ON/OFF Double Pole Switch

Double PVC cable

Cable

Brown or Red = Live (L)

Blue or Black = Neutral (N)

Green or Green/ Yellow = Earth ( )

Fig. 4

Fig. 5

8.8 ect the LCD ay c le from front Conn displ ab

cov Maer to the in Control PCB. Cla abmp the c le

to the rrect position. co CHEC TH WIRING K IF E

CONNECTION S CORRECT and ce the I repla

cover. (Fig. 6a)

8.7 nect the c le as f ng: (Fig. 5)Con ab ollowi

BROWN or RED --L E (L)IV

BLUE or BLACK --NEUTRAL (N)

GREEN or GREEN/YELL --EARTH ( )OW

Ground

ELCB 15mA

Ground

ELCB 15mA

Ground

ELCB 15mA

Fig. A correct wiring connection

Fig. B wrong wiring connection (neutral and

earth reversed)

Fig. C wrong wiring connection (live connected

to neutral , neutral connected to earth)

8.9 Ex le of amp wro wiri onnng ng c ection to the

Electric Water Heater

Min.

80 mm

REV 0

Fig. 6

12 12

15 15

*For Pump Model only

3.4 If the Red (POWER) Indicator does not go off

when you turn off the water, switch OFF the

mains supply and contact Electrolux Consumer

Care Centre for repair service.Special skill is

required for repairing.

NEVER try to repair the unit by yourself.

RAIL BRACKET COVER & CAP DISMANTLE STEPS

RAIN SHOWER SET INSTALLATION PROCEDURES (MALAYSIA ONLY)

RAIL BRACKET OPEN THE RAIL

BRACKET COVER

BY TURNING ANTI

CLOCKWISE & USING

SCREW DRIVER TO

OPEN THE CAP

RAIL BRACKET

COVER COME-OUT

shower holder

top rail bracket

slider rail

selector valve

1. 2.

STEP 1

Insert the Top Rail Bracket, Adjustable Shower Holder,

Soap Tray & Bottom Rail Bracket to the Slider Rail.

STEP 2

Connect the Selector Valve to the bottom of Slider

Rail.

soap tray

slider rail

soap tray holder

soap tray

Fig. 3B

For Soap Tray

- Insert Soap Tray Holder into Soap Tray

hole. (Fig. 3B)

- Then insert soap tray (with Soap Tray Holder)

into Slider Rail.

- Soap Tray shall be insert to the Slider Rail

after Shower Holder.

Fig. 3A

bottom rail bracket

38mm

1300mm 650mm

wall plug hole screw

mounting terminal

Select a suitable position for the Rain Shower Set

then mark 4 screws point (2 on top and 2 on bottom).

The gap of 2 screw hole was 38mm. It is

recommended that the Top Rail Bracket position at

height of 1950mm to the floor and Bottom Rail

Bracket 1300mm to the floor.

wall plug

STEP 4

Use 6mm diameter drill and make the wall plug

holes in depth of 34mm. Insert the wall plugs and

mounting terminal firmly in position with the screw

provided.

STEP 3

rail

bracket cap

hexagon tool

plastic nut

STEP 5

Mount the Slider Rail (connected with Rail Bracket,

Adjustable Shower Holder and Selector Valve)

to the mounting terminal by turns the terminal cover.

5. 6.

STEP 6

Remove the cover and cap from the Rail Bracket

(Fig. 3A) and screw the rail bracket by turning the cover

clockwise. Using hexagon tool to tighten the plastic nut

to the desire position and then replace the cover.

rail bracket

cover

1200mm

650mm

100mm

PVC hose

rain

shower

head

shower

head

7. 8.

STEP 7

Connect the Rain Shower Head to the top of Slider

Rail, 1.5Meter PVC Hose to Hand Shower Head and

1Meter PVC Hose to the Heater. Connected be sure

to put in the Rubber Washer.

STEP 8

Recommended Height for Rain Shower Set.

rubber

washer

7. PLUMBING PROCEDURE

CAUTION ! IMPORTANT !

WARNING !

This Electric Water Heater is a single point system

and the “Water Outlet” can only be fitted to the

PVC Hose and Handshower set provided.

CONTROL VALVE OR FITTING CANNOT BE

ALLOWED FITTING TO THE WATER OUTLET.

7.1 Connect the 3 in 1 Stop Valve to the Water

Inlet connect with washer. Use correct tools to

tighten and be careful not to over tighten and

damage the plastic nut.

7.2 Connect the incoming water piping to the

3 in 1 Stop Valve (1/2” BSP). Make sure to put

the Mesh Filter between

3 in 1 Stop Valve and incoming water piping.

7.3

Turn on the water mains to drain out all

plumbing dirts, at the same time fill up the

heater tank before connect shower head.

7.4 Connect the shower head to the hose.

(rain shower installation procedure step 7)

(Be sure to put in the Washer.)

7.6 THE HEATER TANK MUST BE FILLED UP

WITH WATER BEFORE TURNING ON THE

ELECTRICITY SUPPLY TO PREVENT ANY DRY

BURNT DAMAGE TO THE HEATING ELEMENT.

7.7 Hook the Handshower to the Slider Rail

Shower Holder and adjust to your ideal position.

7.8 Check if any water leakage.

7.9 Do not use white tape during piping installation.

7.10 THE WATER INLET AND OUTLET MUST BE

INSTALLED IN CORRECT DIRECTION,

OTHERWISE HEATER UNIT WILL NOT FUNCTION.

7.11 DO NOT APPLY PLUMBING CEMENT ON

CONNECTION. WHENEVER NECESSARY, USE

ONLY THREAD OR SEALING TAPE AT 3 IN 1

STOP VALVE INLET ONLY. (FIG 2)

7.12 Must use 3 in 1 Stop Valve accessories

provided with the electric water heater.

For Pump Model, it is highly recommended to

connect Water Inlet Connection to storage

supply tank , otherwise it may cause damage to

the Pump Motor.

7.5 Connect the Hose to the water outlet.

(rain shower installation procedure step 7)

(Be sure to put in the Washer.)

1. PARTS IDENTIFICATION (RAIN SHOWER MODEL)

1. Front Cover

2. Main Display

(*LED Display Main PCB

Board behind front cover)

3. 3 in 1 Stop Valve

i) Stop Valve

ii) Flow Regulator Valve

iii) Built-in-Filter

4. Mesh Filter

5. Rail Support

6. Handshower

7. Adjustable Shower Holder

8. PVC Hose

9. Soap Tray

10. Slider Rail

11. Terminal Block

12. Thermostat (Double-Action)

13. Heater Tank

14. PCB Board (Test & Reset)

15. ELCB Board

16. Water Outlet Connection

17. SMPS PCB Board*

18. DC Pump*

19. Heater Base

20. Triac

21. Flow Sensor

22. Water Inlet Connection

23. Rating Label

24. Rain Shower Head

25. AC Pump*

26. Test & Reset Button

27. Logo Light

Fig 1a. (Malaysia only)

AC Pump Model* DC Pump Model*

26 23

12 12

*For Pump Model only

EWE361MB-DST1

EWE361MA-DST1

NORMAL SHOWER INSTALLATION

(

Thailand, Indonesia, Philippines & Vietnam model

)

(THAILAND, INDONESIA, PHILLIPINES & VIETNAM MODELS)

3.6 15.0 4.0 7 / 0.85mm 56 / 0.30 mm 32 32

240V ~

50/60 Hz

(Malaysia

model only)

9.2 MANUALLY CHANGE TEMPERATURE

(i)

(ii)

(iii) (iv)

Press (+) button

- ee goes up. Degr

- P er display bar level c ges ow han

acc gly to reach the des ed ordin ir

t rature.empe

Press and hold (+) button for 2 sec

- T rature gits rises at faster s ed empe di pe

up to the max um 45 ee.im degr

- P er display bar just acc ly. ow ad ording

- If actual t rature c not reach the SET empe an

t rature, the “MAX” ll ow & empe wi sh blink. If

the actual t rature reaches SET t ratureempe empe

, “MAX” ll dis ar.wi appe

- ee es wn. Degr go do

- P er display bar level cow hanges

acc gly to reach the des ed ordin ir

t raturempe e.

- T rature gits falls at faster sempe di pe doed wn to 32

ee and stop autosc ll.degr ro

- P er lay bar just acc gly.ow disp ad ordin

- If the setting reached 32 degree, presses DOWN

button one re time ll t er the cold water function.mo wi rigg

The temperature can be gradually controlled by pressing either UP or DOWN button: -

Notes: The ry icator ll ar in the ent that the al ection for the t rature memo ind wi appe ev manu sel empe

and/or mp (*) v ue nation ch is same as st ed ry, the ry icator ll ghts up.pu al combi whi or memo memo ind wi li

Press (-) button Press and hold DOWN button for 2 sec

9. TEST OPERATION

9.1 TEST RUN

- The icons ll ink 2 times arth, wi bl (e

overheating, electrical leak and

t mistor) after switch ON.her

(i)

(ii)

(iii)

when the 3 in 1 stop valve is turns on

SafeReady

- Last used setting ll be activate if the wi

3 in 1 stop valve is turns on.

Before switch ON electricity supply, please check the electrical wiring connection properly to the

Electric Water Heater : -

- When 3 in 1 stop valve is turns off,

Electric Water Heater goes to

pre-standby.

- If the 3 in 1 stop valve not ON, after 5

minutes will go to standby mode. (50% light dimmer,

after 15 minutes, the light will turn off)

(iv)

9.3 COLD SHOWER SHORTCUT

Water heater is running

- User presses the cold s er how

button.

- After Pressed display c ed hang

to 8.3 i). (i

(i)

(ii)

- Electric Water Heater turn off the heating element.

- Temperature digits changes to two lines.

- The cold setting ( ) icon lights up on the display.

Cold shower function can be activate via shortcut button: -

Cold setting activated

9. TEST OPERATION

(CONT’D)

(iii) (iv)

- Presses the cold shower button

then display will go back to

previous setting.

Cold setting deactivated Cold setting deactivated (Alternative)

- Pressing the M1/ M2/ M3 will go to memory setting.

- Pressing up button will adjust setting temperature.

- Pressing down button will not affect cold setting.

9.4 FOR PUMP MODEL

The pump will ON when the Power supply on and 3 in 1 Stop Valve opened.

N otes: 1. If actual t rature c not reach the set t rature, full er bar ll be s wn and empe an empe pow wi ho

‘MAX’ dis ay ll ink.pl wi bl

It ght due to flow rate too gh or inc ng water t rature too low. mi hi omi empe

Adjust the 3 in 1 stop valve to uce water flow.red

2. It is ed not to rate the mp for re than 30 nutes. recommend ope pu mo mi

(iii) (iv)

- Press any button except your c ent urr

s ected ory (1, 2 & 3) and el mem

EcoS er button to exit your selected how

ory.mem

Deactivate the memory function - The ory dicator ll ar in mem in wi appe

the event that the selecte d t ratureempe

v ue are the same as st ed ory, al or mem

the ory icator ll ghts up.mem ind wi li

9.5 MEMORY SETTING

Memory function

- P ss M button for 3 sec ds, ry 1, 2re on Memo

d 3 l r.an wil appea

- P ss M button to s ct the y r,re ele memor numbe

s ected ry r l k.el memo numbe wil blin

- P ss the T at e (+) or ) to c ose re emper ur (- ho

des e t at e d ave for 3 sec ds.ir emper ur an le on

- Once p to ate the sett g has n bee indic in bee

st d.ore

(i)

(ii)

This Electric Water Heater allows user to store up to 3 desired settings (M1/ M2/ M3) for easy access: -

Memory selection

- User may selects a des ed stir ored setting

by pressing M button.

9.6 ELCB TESTING

This procedure is highly recommended to test at least once a month:-

Press TEST button

- The E1 ay ink & ep 3 times displ bl be

and auto turn OFF.

(i)

a) ELCB ok: -

Press TEST/ RESET button

- The E4 ay ink & ep 3 times displ bl be

and auto cut off, c not be set and an re

ease contact Elect lux cust er pl ro om

rvice call centre.se

(i)

b) ELCB failure: -

(ii)

Press RESET button

- The Electric Water Heater recover, the

icons arth, ov eating, electrical leak (e erh

and t mistor) ll ink 2 times & back to her wi bl

evious display. pr

ELCB TEST/RESET BUTTON

9.8 ECOSHOWER OPERATION

Normal usage

(i)

- al display en 3 in 1 Norm wh

stop valve ng turns on. bei

EcoShower is to calculate water consumption by bucket (1 bucket = 20 Liters) and have Eco friendly

environment benefits for user notification of water consumption on each shower. EcoShower will start activate

whenever 3 in 1 stop valve being turns on.

9.7 LOW WATER PRESSURE

(i)

(ii)

Low water pressure

- Low water pressure dicator ll be in wi

ed on sc en en water pressure appear re wh

is er than activation flow rate. low

ow water essure dicator ll be (L pr in wi

occas al dis ed if water pressure is ion appear

too low ow 0.8 Litre/min, the display ll bel wi

be me to the e-st dby sc en and beco pr an re

we can not activate any button on the display

of Electric Water Heater).

- Pump button ways ghts up if the al li 3 in 1

stop valve en ng e-st dby de op duri pr an mo

(For el with mp function only). mod pu

- ng the st dby de, en turn on the Duri an mo wh

3 in 1 stop valve, if the water flow rate still

c not activate the Electric Water Heater, the an

low pressure dicator ll be ed.in wi appear

Activate pump function

- To increase the water pressure, user presses and

ld the ( ) button for few sec ds.ho on

- Pump activate at full s ed and flow rate ll be pe wi

increased.

- Low water pressure dicator ll be dis ed in wi appear

and the Electric Water Heater ll work lly if wi norma

the flow rate can be intain er than the ma high

activation flow rate.

- If the Electric Water Heater still be not le to intain ab ma

the flow rate above the activation flow rate and the Low

water pressure dicator still ar, user may eat in appe rep

the above step by presses and ld (ho ) button.

(It is not rec ed to eat the step re than ommend rep mo

3 times if the water pressure still be not st le and ab

c not intain above activation flow rate).an ma

- It is not rec ed to rate the mp for re ommend ope pu mo

than 30 nutes. mi

This Electric Water Heater can start and function at minimum rated flow rate . :-

(iii) (iv)

- The EcoS er ration cont ues.how ope in

- The EcoS er bucket counter ll how wi

acsent 1 bucket each time the

EcoS er liters counter reach 20 liters. how

- The EcoS er liters counter ll be reset how wi

to 0 each time en ch 20 liters. wh rea

(Present display 1 bucket & 0 liters

ng to 20 liters water consumption)meani

- Turn off the 3 in 1 stop valve the display es go

into -st dby.pre an

- If the user cont ue s er within in how 15 nutes mi

from previous section, the counter ll cont ues. wi in

(Present display 3 bucket & 5 liters ng to 65 meani

liters water consumption)

10.

HANDSHOWER SPRAY

This Innovative adjustable Handshower has 5 different spray patterns (STANDARD, JUMBO, SOOTHE,

MIX and MASSAGE. The patterns are described as following:

Fig. 7

STANDARD SPRAY SOOTHE SPRAY JUMBO SPRAY MIX SPRAY MASSAGE SPRAY

Move the Handshower to the desired angle. A ratchet mechanism in the Shower Holder will hold the

Handshower in selected position. (Fig. 8)

Holder

Knob

Fig. 8

11. MAINTENANCE

10.1 TEST THE ‘ELCB’ REGULARLY

(This procedure is highly recommended test

at least once a month)

Turn on the electricity and water supply, LCD

display will lights up after self checking.

Press the ELCB Test Button, Electric Water

Heater should go off. Press the Reset Button

to resume the electricity supply.

(Refer to 8.6)

10.2 CLEAN THE FILTER REGULARLY

Clean the Mesh Filter regularly to prevent

blockage. (Fig. 9) Remove the Built-in Filter

by turning its cap anticlockwise. Whenever

need flush the internal stainer with water to

remove any trapped sediments. (Fig. 10)

Whenever fixing back the Built-In Filter,

beware of the alignment of Internal Strainer.

Use the protruded guideline within 3 in 1

Stop Valve to position the Internal Strainer.

Read the section ‘ 3. SAFETY INFORMATION ’ first.

WARNING !

10.3 If the Electric Water Heater does not

go off when you press the ELCB Test Button,

switch OFF the mains supply and contact

Electrolux Customer Service Call Centre for

repair service. Special skill is required for

repairing. NEVER try to repair the unit by

yourself.

10.4 CLEANING PRECAUTION !

Do not use thinner,alcohol,petrol or any other

organic solutions to clean the set. Use only

damped cloth with mild detergent.

Fig. 10

FILTER UNIT CLEANING

12. TROUBLESHOOTING

Problem/Symptom Cause Action/Cure

Electric Water Heater

fail to rate, no ope

power.

Int upted err pow super ply.

Electric Water Heater

malfunction.

Water too hot. Not gh water f ingenou low

t gh the s er.hrou how

Blockage in water ply.sup

Inc ng water omi

t rature too gh.empe hi

Water too cool or cold. Too much water flow.

Water pressure lowbe

minimum ed andrequir

water heater not function.

Inc ng water omi

t rature too low.empe

Electrical malfunction of

Electric Water Heater.

Safety T mostat cher ut-out

operated.

Check the re c nection and in werwi on ma po

s ply f it still fail to up . I operate, contact

Elect lux Custro omer Service ll Centre.Ca

Check other ances are having same appli

phenomenal and contact cal Electricity lo

S ly any. Let the Electric Water upp Comp

Heater checked f it still fail to rate, . I ope

contact Electrolux Customer Service Call

Centre.

I ease flow rate via water flow cont lerncr ro

or 3 in 1 Stop v ve.al

Blocked of s er ad - c an how he le or lace.rep

Check if 3 in 1 stop v ve are fully turns on.al

Cleaning sh Filter and Built In Filter. Me

(Refer to 10.2)

Reduce the setting t rature viaempe

t rature uster. (Up , wn button)empe adj do

Reduce flow rate via water flow cont er rol

or 3 in 1 Stop v ve.al

Check water supply from ins or tank fed? ma

If tank fed, mb to ins water s ply replu ma up

and check if the water pressure is gh.enou

If mains fed, make sure that mains

3 in 1 stop valve is fully turns on and that

t re are no other restrictions in the water he

s ly le water heater is in use. upp whi

I ease the setting t rature viancr empe

t rature uster or 3 in 1 Stop valve.empe adj

Contact Electrolux Cust er Service ll om Ca

Centre.

Safety T mostat cut-out rated. her ope

Contact Electrolux Customer Service Call

Centre.

Water flow too low.

3 in 1 Stop Valve Filter /

Mesh Filter ocked.bl

Clean the filter (refer 10.2).

3 in 1 Stop Valve not

fully open.

-Open 3 in 1 Stop Valve to re flow rate.desi

Water s ply insufficent.up - Check house water ly.supp

Water hot after close

and en of 3 in 1 reop

Stop Valve or Water

Tap.

Water t rature herempe hig

than set temperature when

3 in 1 Stop Valve or Water

Tap is OFF a le and whi

reopen in.aga

Avoid s er with water output in that how

period.

Let the water flow few seconds before

cont ue bat ng. in hi

12. TROUBLESHOOTING (CONT’D)

Notes:

* It is advised all electrical int ance/ rs to the s er s ld be cma en repai how hou arried out by

a suitably lified person. qua

* In the unlikely event of Electric Water Heater f re other than detailu ailed in the fault findi pang ge,

please contact Elect ux Cust er Service ll Centre for advice.rol om Ca

Problem/Symptom Cause Action/Cure

Electrical leak can be

t ed at any time in rigger Contact Electrolux Cust er S ce Callom ervi

Centre.

If the Electric Water Heater is

not earthed ly, the earth proper

icon ll wi appear on sc en re

during usage or st dby.an

The E2 and t mistor iconher

will ar and nk on sc en appe bli re

in sync nisation with the hro

beep due to t istor E or. herm rr

E4 ll wi blink in synchronisation

with the beeps 3 times if the

Its rec ed er must have er omend us prop

earth c ected to water heater.onn

Contact Electrolux Cust er Service Callom

Centre.

The on nk until t ratureic bli empe

drop then return to malnor

funct lity. iona

In the re case, the on ra ic does not return

to al funct lity (safety t ostat norm iona herm

cut

-out rated), Contact Electope rolux

Cust er S ce ll Centre.om ervi Ca

Contact Electrolux Cust er S ce Callom ervi

Centre.

Display a arppe E1 with

Display a ar Ear Iconppe th

Display a arppe E2 and

Th rm store i Icon

Display a ar ppe

o h t iconver ea

Display a r E4ppea

Earth icon also appear if Live

& Neutral reverse c ectiononn

-Connect ve / Neutral ectly.Li corr-

The heater ll be stops wi

working and shows the

ov eat icon nking and erh bli

beep 3 times if the t rature empe

meas ed is ur above 55 degrees.

13.WIRING DIAGRAM

WIRING DIAGRAM-DPDT*MODEL (NO PUMP/AC PUMP)

LIVE

NEUTRAL

TRIAC

Nout

in )

Main Supply

220/230/240 V~a.c.

MAIN CONTROL BOARD

TOUCH SCREEN

Electronic

ELCB,15mA

Sensit ivity

Reset

Test

FLOW SENSOR ASSY.

Lout

Auto -Reset * Ma nual-Reset

Double Act ion Thermost at

EARTH

(*) For PUMP Model

AC PUMP

(*) For PUMP Model

* Manual Reset (90°C Thermostat)

For Models rated 4.8kW and below, thermostat is manually resetable.

For models rated 6.0kW and above, thermostat needed to be replaced

once permanently tripped.

* DPDT : Double Pole Double Action Thermostat

WIRING DIAGRAM-DPDT*MODEL (FOR VIETNAM MODELS ONLY) (DC PUMP)

LIVE

NEUTRAL

TRIAC

Nout

)

Main Supply

220/230/240 V~a.c.

Electronic

ELCB, 15mA

Sensitivity

Reset

Test

FLOW SENSOR ASSY.

Lout

Double Action Thermost at

EARTH

(*) For PUMP Model

Heating Element A

Heating Element B

Auto-Re set * Manual-Reset

Relay 1

Relay 2

Relay 3

MAIN CONTROL BOARD

TOUCH SCREEN

SMPS PCB

ASSY

Silent Pump

14.

ELECTRICAL SPECIFICATION

Note : The specification, actual product’s cosmetic design and accessories parts shown are

correct at the time of printing and may be subjected to change without prior notice.

3.5 kg - ELCB , DPDT, NO PUMP

4.6 kg - ELCB , DPDT, AC PUMP

3.8 kg - ELCB , DPDT, DC PUMP

2 Litre / min

6.0 Bar (0.6 MPa ; 87.02 psi)

ELECTRONIC POWER CONTROL

TYPE

ELECTRICAL LOADING

Min. WATER FLOW RATE

Max. INLET WATER PRESSURE

WATER CONNECTION

DIMENSIONS

GROSS WEIGHT

2.4kW 220V a.c. 10.9A 50Hz and 60Hz

3.8kW 220V a.c. 17.3A 50Hz and 60Hz

4.5kW 220V a.c. 20.5A 50Hz and 60Hz

4.8kW 220V a.c. 21.8A 50Hz and 60Hz

1/2” BSP SINGLE POINT SYSTEM

220 (W) X 401 (H) X 80 (T) mm

Min. INLET WATER PRESSURE

0.1 Bar (10 kPa ; 1.45 psi)

CONSUMER CARE

Indonesia

Hotline service: 08041119999

PT. Electrolux Indonesia

Electrolux Building

Jl.Abdul Muis No.34, Petojo Selatan,

Gambir Jakarta Pusat 10160

Email:customercare@electrolux.co.id

SMS & WA : 0812.8088.8863

Malaysia

Consumer Care Center Tel: 1300-88-11-22

Electrolux Home Appliances Sdn. Bhd.

Corporate Office Address: Unit T2-7, 7th Floor, Tower 2 ,

Jaya33 Hyperoffice, No. 3, J alan Semangat, Seksyen 13,

46100 Petaling Jaya, Selangor

Office Tel : (+60 3) 7843 5999

Office Fax : (+60 3) 7955 5511

Consumer Care Center Address: Lot C6, No. 28,

Jalan 15/22, Taman Perindustrain Tiong Nam,

40200 Shah Alam, Selangor

Consumer Care Center Fax : (+60 3) 5524 2521

Email : malaysia.customercare@electrolux.com

Philippines

Consumer Care Center Toll Free : 1-800-10-845-CARE 227

Cons umer Care Hotline : (+63 2) 845 CARE 2273

Electrolux Philippines, Inc.

10th Floor. W5th Avenue Building

5th Avenue Corner 32nd Street

Bonifacio Global City,

Taguig Philippines 1634

Trunkline: +63 2 737- 4756

Website : www.electrolux.com.ph

Email : wecare@electrolux.com

Singapore

Consumer Care Center Tel: (+65) 6727 3699

Electrolux S.E.A. Pte Ltd.

1 Fusionopolis Place,

#07-10 Galaxis, West Lobby

Singapore 138522.

Office Fax : (+65) 6727 3611

Email : customer-care.sin@electrolux.com

Thailand

Consumer Care Tel : (+66 2) 725 9000

Electrolux Thailand Co., Ltd.

Electrolux Building 14th Floor

1910 New Phetchaburi Road,

Bangkapi, Huai Khwang, Bangkok 10310

Office Tel : (+66 2) 7259100

Office Fax : (+66 2) 7259299

Email : customercarethai@electrolux.com

Vietnam

Consumer Care Center Toll Free : 1800-58-88-99

Tel : (+84 8) 3910 5465

Electrolux Vietnam Ltd.

Floor 9th, A&B Tower

76 Le Lai street - Ben Thanh Ward - District 1

Ho Chi Minh City ，Vietnam

Office Tel : (+84 8) 3910 5465

Office Fax : (+84 8) 3910 5470

Email : vncare@electrolux.com

Hongkong

Tel: (+852) 8203 0298

Dah Chong Hong, Ltd. - Service Centre

8/F., Yee Lim Godown Block C

2-28 Kwai Lok Street, Kwai Chung, N.T.

Fig. 9

OPEN

INTERNAL

STRAINER

OPEN CLOSE

FLOW REGULATOR

MESH FILTER

BUILT-IN FILTER

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with

it decades of professional experience and innovation. In genious and stylish, it has been

designed with you in mind. So whenever you use it, you can be safe in knowledge that

you’ll get great results every time. Welcome to Electrolux.

Visit our website to:

Get usage advice, brochures, trouble shooter, service information:

www.electrolux.com

www.registerelectrolux.com

Buy Accessories, Consumables and Original spare parts for your appliance:

www.electrolux.com/shop

CONSUMER CARE AND SERVICE

We recommend the use of original spare parts.

When contacting Service, ensure that you have the following data available.

The information can be found on the rating plate. Model, PNC, Serial Number.

(Right side of unit).

Warning/ Caution-Safety information.

General information and tips.

Environmental information.

Subject to change without notice.

- If the user did not shower more than 15 minutes,

the counter will reset to zero.

synchronisation with the

beeps 3 times during usage

or standy.

ELCB have problem during

ELCB test.

3.6kW 240V a.c. 15.0A 50Hz and 60Hz

WIRING DIAGRAM-DPDT*MODEL (DC PUMP)

LIVE

NEUTRAL

TRIAC

Nout

)

Main Supply

220/230/240 V~a.c.

MAIN CONTROL BOARD

TOUCH SCREEN

Electronic

ELCB,15mA

Sensitivity

Reset

Test

FLOW SENSOR ASSY.

Lout

Auto- Reset * Manual-Reset

Double Action Thermostat

EARTH

SMPS PCB

ASSY

Silent Pump

Product specificaties

Merk:	Electrolux
Categorie:	Ketel & boiler
Model:	EWE361MB-DST1

Heb je hulp nodig?

Als je hulp nodig hebt met Electrolux EWE361MB-DST1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ketel & boiler Electrolux

Electrolux EWH30SIEEC Handleiding

20 December 2023

Electrolux EWH100SIEEC Handleiding

8 December 2023

Electrolux EWH100SIBEEEC Handleiding

8 December 2023

Electrolux EWH80SI Handleiding

8 December 2023

Electrolux EWH80SIBEEEC Handleiding

8 December 2023

Electrolux EWH50SIEEC Handleiding

7 December 2023

Electrolux EWH30SIBEEEC Handleiding

7 December 2023

Electrolux EWH80SISEEEC Handleiding

7 December 2023

Electrolux EWE451PX-DWX5 Handleiding

10 Augustus 2022

Electrolux EWE351GX-DWX Handleiding

18 Juni 2022

Handleiding Ketel & boiler

Nieuwste handleidingen voor Ketel & boiler

Rinnai EHPA250VMAWH Handleiding

21 November 2024

Rinnai ECF29i50 Handleiding

21 November 2024

Rinnai ECF19i60 Handleiding

21 November 2024

Rinnai FM10NA Handleiding

20 November 2024

Nibe UKV 1000 Handleiding

19 November 2024

Nibe VPBS Handleiding

18 November 2024

Vaillant AtmoMAG mini 11-0/0 XZ Handleiding

16 November 2024

Teka EWH 100 Handleiding

15 November 2024

Hitachi HES-45VS Handleiding

15 November 2024

Philips AquaShield AWH1626 Handleiding

12 November 2024