Electro Harmonix Nano Looper 360 Handleiding

Electro Harmonix Niet gecategoriseerd Nano Looper 360

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Nano Looper 360 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 195 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

NANO LOOPER 360

Compact Looper

Congratulations on your purchase of the Nano Looper 360 The Nano Looper 360 is ! a

small, extremely easy to use looper with a total of -seconds of loop recording time. Not 360

only that, the available 360 seconds can be divided into 11 different Loops, so you get the

most out of the available memory! You can think of the Nano Looper 360 as your very own

“Loop Locker. ”

WARNING: Your Nano Looper 360 comes equipped with an Electro-Harmonix 9.6DC-

200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The Nano

Looper 360 requires 90mA at 9VDC with a center negative plug. Using the wrong adapter

or plug polarity may damage your unit and void the warranty.

– – FEATURES

- 6 minutes of loop recording time

- selectable independent Loops 11 , , that remain in memory until you erase them

- High quality uncompressed audio: -bit A/D/A, 44.1k Sample Rate , 24 Hz

- Intuitive looping interface

- Undo-Redo function

- Unlimited overdubbing

- Small pedal board footprint

- AC Adapter Included

- tionally may use 9V Alkaline Battery, battery life: approximately 4 hours of operation Op

(varies on conditions of use)

– – CONTROLS

LEVEL Knob – Controls the output level of the Loop. Your dry signal remains at unity

signal level from input to output. The dry signal also remains analog throughout the . 360

LOOP Knob Selects number: 1-11. When scrolling through loops, the –Loop MEM LED

flash quickly during transitions. If the loop has no recorded memory, the es MEM LED

remains off. If the loop has recorded memory, the remains and playback can MEM LED on

begin.

INPUT Jack Nano Looper 360. The input – This ¼” jack is the audio input for the

impedance is 2.2M . 

OUTPUT Jack Nano Looper 360. The output – This ¼” jack is the audio output from the

impedance is 470.

9V Power Jack – Plug the output of the supplied AC adapter into the 9V power jack

located at the top of the Nano Looper 360. The Nano Looper 360 draws mA at 9VDC 90

with a center negative plug. The Nano Looper 360 accepts Boss® and Ibanez® style AC

Adapters.

– – QUICK START GUIDE

RECORDING A LOOP

1. To record a Loop; simply select an empty bank and press the once. The Footswitch

REC LED will light solid and recording begins immediately.

2. To stop recording the l press the again once. The will turn oop, Footswitch REC LED

off, the will turn on, and the loop will begin playing immediately. The PLAY LED

MEM LED will also light solid, indicating the presence of recorded loop memory.

3. All Loops play indefinitely. Each time the loop repeats, the will turn off PLAY LED

briefly.

4. After a loop is recorded, the length is subtracted from the total loop recording time.

5. Note: if the full 360 seconds of Loop Recording time is reached, recording will stop

automatically. The will turn off, the will turn on, and the Loop REC LED PLAY LED

will begin playing immediately. The will also light solid, indicating the MEM LED

presence of recorded l memory. oop

STOPPING & STARTING LOOP PLAYBACK

1. To stop loop playback, press the two times quickly. Footswitch

2. Note: REC LED the will turn on together with the during the first press. PLAY LED

Both LEDs turn off during the second press and playback stops immediately.

3. While stopped, press and release the Footswitch once to start playback. The PLAY

LED will light indicating the loop is playing.

RECORDING AN OVERDUB

1. To record an overdub, make sure a L is playing back. If a loop is not playingoop ,

press the once to begin playback. The will turn on and the Footswitch PLAY LED

loop will begin playing immediately.

2. To start recording an overdub, press the once. The will turn Footswitch REC LED

on, together with the , and audio will be recorded on top of the original PLAY LED

loop. No volume loss will occur to the previously recorded portion of the loop.

3. To stop overdubbing the loop; press the again once. The will Footswitch REC LED

turn off, and the loop will continue playing along with the overdubbed audio.

4. Overdubbing will never change the length of the loop.

5. If the loop repeats during overdubbing, the and will both turn REC LED PLAY LED

off briefly. The Nano Looper 360 can overdub indefinitely, allowing you to

continuously overdub new audio onto your loop.

6. After finishing an Overdub, the UNDO-REDO function is enabled. You may undo,

then redo the last Overdub as many times as you like.

UNDO-REDO FUNCTION

1. The Undo/Redo function can only be initiated while a loop is playing back. Undo/Redo

cannot be performed during Overdub, Record or Stop modes.

2. To undo an overdub (remove the last take) during l playback, press and hold the oop

Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub

will be removed.

3. To redo an overdub (restore the last take) during l playback, press and hold the oop

Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub

will be restored.

4. Note: once UNDO-REDO is enabled, this function is available until the loop is erased.

This is true even if returning to a loop from a previous selection, or even after power

cycling.

ERASING A LOOP

1. To erase a loop, play-back must be stopped. If a loop is playing, press the

Footswitch two times quickly.

2. Press and hold the for 2 seconds. The will blink six times then Footswitch MEM LED

remain off, indicating the loop is erased.

3. Note: the ERASE function is only enabled when the loop has recorded memory, as

indicated by the remaining lit. MEM LED

LOOP MEMORY

1. Any recorded audio is stored automatically to the Nano Looper 360’s internal memory.

2. All recorded loops will remain in memory until they are erased. Power cycling does not

erase loops unless power is cut while recording the loop. Any loop or overdub that

was being recorded at the time of power loss will not be saved by the 360.

3. After loop is recorded, the length is subtracted from the total l recording time. a oop

For example, if a 60 second loop is recorded on Loop 1, there are 300 seconds still

available for Loops 2-11. Overdubbing on top of any given loop does not subtract

from total loop recording time.

4. When the full 360-seconds loop recording time depleted, recording a of is new loop

is inhibited. If an empty Loop is selected and recording is attempted, the MEM-LED

will blink twice. To free-up recording memory, select a loop with recorded memory

and erase it.

FACTORY RESTORE

1. To initialize a Factory Restore, unplug the power jack.

2. Set the Loop Knob to Loop 11.

3. Plug in the power jack while down the footswitch until all three LEDs begin to holding

flash, this takes about 2 seconds. Factory restore will not begin until all three LEDs

are blinking. If you change your mind before the three LEDs begin to blink, release

the footswitch or move the LOOP knob to another loop location other than 11.

4. Once all three LEDs start blinking you can release the footswitch. All three LEDs will

continue to flash until the Factory Restore process is complete (~4 seconds). After the

process is complete, the MEM LED will flash quickly and Loop 11 will be selected.

5. Note: All Loop audio is erased during Factory Restore, and the process cannot be

undone.

– – CHANGING THE BATTERY

To change the 9-volt battery, you must remove the 4 screws on the bottom of the Nano

Looper 360. Once the screws are removed, you can take off the bottom plate and change

the battery. Please do not touch the circuit board while the bottom plate is off or you risk

damaging a component.

Battery life is icated by the three LEDs. These LEDs will fail to turn-on with a dead ind

battery. If the 360 fully discharges a battery during normal operation, all LEDs will turn-off

and prevent all functions. The battery must be changed immediately.

Product specificaties

Merk:	Electro Harmonix
Categorie:	Niet gecategoriseerd
Model:	Nano Looper 360

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Nano Looper 360 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Electro Harmonix

Electro Harmonix Memory Boy Handleiding

16 November 2024

Electro Harmonix Soul POG Handleiding

16 November 2024

Electro Harmonix OD Glove Handleiding

16 November 2024

Electro Harmonix Crayon 69 Handleiding

16 November 2024

Electro Harmonix Good Vibes Handleiding

12 November 2024

Electro Harmonix Cock Fight Handleiding

9 Juli 2024

Electro Harmonix Cock Fight Plus Handleiding

9 Juli 2024

Electro Harmonix Holy Grail Max Handleiding

9 Juli 2024

Electro Harmonix The Worm Handleiding

17 Juni 2024

Electro Harmonix Canyon Echo Handleiding

12 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic NB-W250 Handleiding

25 November 2024

Alpine CHM-S611 Handleiding

25 November 2024

AOpen DE3650-C Handleiding

25 November 2024

Lazer Urbanize MIPS Handleiding

25 November 2024

Symmons Dia 353GB-24 Handleiding

25 November 2024

SoundTube IPD-RS62-EZ Handleiding

25 November 2024

Moen Camerist 4905 Handleiding

25 November 2024

Lazer Cameleon DLX Handleiding

25 November 2024

DMT DLD-85 Handleiding

25 November 2024

AOpen AM1120T Handleiding

25 November 2024