Edimax ES-3108P Handleiding

Edimax Schakelaar ES-3108P

Lees hieronder de 📖 handleiding in het Nederlandse voor Edimax ES-3108P (1 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

(2) LED

Table 1-1 LED description

Power is supplied

No power

LED Color Status Description

PWR

(Power) Green

Lit

Off

A valid link is established

No link is established

Data packets received

Off

LNK/ACT

(Link/Act ivity)

SPEED

(10/100M)

Green

Yellow

Lit

Off

Lit This port run at 100Mbps

This port run at 10Mbps

Flash

5/8/16 Port Fast Ethernet Switch

2Installation

1. Operating Environment

This switching hub must be installed and operated within the limits of

specified operating temperature (32-131

0F) and humidity (10-95%

Noncondensing). Do not place objects on top of the unit. Do not obstruct any

vents at the sides of the unit. Do not position the unit near any heating source

such as heater, radiator, or direct exposure to sun. Prevent entering of water

and moisture into the unit. If necessary, use dehumidifier to reduce humidity.

2. Connecting to network devices

The RJ-45 ports on the switch support Auto-MDI/MDI-X function which

allow using straight-through or cross-over type cables to connect this switch

to workstation or hub.

Connect one end of the network cable to the RJ-45 port on the rear panel, and

connect the other end of the network cable to the RJ-45 port on the network

device. Follow the same procedure to connect all the RJ-45 ports of the

switch. The UTP network cables must comply with EIA/TIA 568

specifications and Category 5 standard for 100Mbps data transmission.

Maximum length, using UTP cable, between the switch and connected device

is 100 meters (300ft). Once the network cable is connected to both ends and

the attached network device is powered on, the green LNK/ACT LED should

be lit.

3. Connecting the power

Connect the output end of the power

adapter to the power connector on the

rear panel of the unit. Connect the

power adapter to the power outlet.

The green Power LED on the front

panel should be lit. Figure 2-1 Connect the AC power adapter

DC Power

AC Power

External Power Adapter

3Trouble-shooting

1. Power LED is not lit

z Check if the power cord is properly connected to the external power

adapter and the power outlet. Make sure the DC power jack is firmly

plugged into the power socket of the switch.

2. Link/Activity is not lit when connect to 100Mbps device

z Check the power switch of the network device attached to the switch;

make sure it is turned ON.

z Check the network cable; make sure it is properly connected to the

switch and the network device.

z Check the network cable; make sure the UTP cables comply with

EIA/TIA 568 and Category 5 specification.

[!] Contact your dealer if problem persist.

1Physical Description

(1) Panel

Figure 1-1 Panel description

Power LED

LED Panel

RJ45 Connectors

Power Connector

POWER

100M

LNK/ACT

Fast Ethernet Switch

1 5

2 63 7 8

10/100M LED

Link/Activity LED

8-Port 10/100Mbps

LED Panel

Power LED 100/10Mbps LED

Link/Activity LED

POWER

10 0M

LNK/ACT

Fast Ethernet Switch 12345

RJ45 Connectors

Power Connector

5-Port 10/100Mbps

POWER

100M

LN K/ ACT

3 112 10

1 9

4 12

5 13

6 147 15

8 16

Fast Ethernet Switch

LED Panel

RJ45 Connectors

Power Connector

100/10Mbps

Link/Activity LED

Power LED

16-Port 10/100Mbps

5-Port

8-Port

16-Port

Product specificaties

Merk:	Edimax
Categorie:	Schakelaar
Model:	ES-3108P
Gewicht:	370 g
Certificering:	FCC, CE Mark, C-Tick
Power over Ethernet (PoE):	Nee
Max. overdrachtssnelheid:	0.1 Gbit/s
MAC-adrestabel:	2048 entries
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	8
Afmetingen (B x D x H):	187 x 100 x 30 mm
Packet buffergeheugen:	0.125 MB
Full duplex:	Ja
Overdrachtssnelheid:	10 Mbit/s
Bedrijfstemperatuur (T-T):	0 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 95 procent