Durkopp Adler 975 Handleiding

Durkopp Adler Naaimachine 975

Lees hieronder de 📖 handleiding in het Nederlandse voor Durkopp Adler 975 (57 pagina's) in de categorie Naaimachine. Deze handleiding was nuttig voor 122 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/57

Contents Page:

Part 3: Service Instructions Cl. 975 - 1 - 5

1. General ................................................. 3

2. Machine Head ............................................. 4

2.1 LoopingStroke............................................. 4

2.2 Needle Bar Height and Clearance of the Hook Point to the Needle . . . . . . . . . . . . . . . . 5

2.3 NeedlePlate .............................................. 6

2.3.1 Lateral Position of the Needle Plate Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3.2 Upper and Lower Position of the Needle Plate Carrier . . . . . . . . . . . . . . . . . . . . . . . 7

2.3.3 Timing of the Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3.4 Speed of “ Needle Plate Up and Down ” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 BobbinCaseOpener.......................................... 10

2.4.1 Height of the Finger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4.2 Size of the Opening Gap ( Position of the Finger Run ) and Finger Depth . . . . . . . . . . . . 11

2.4.3 TimingtheOpening .......................................... 12

2.5 PressureFoot ............................................. 13

2.5.1 Pressure Foot Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.5.2 Height Adjustment Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.5.3 Timing of the Pressure Foot Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.6 Thread Controller Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.7 Thread Tension Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.8 Lubrication ............................................... 18

2.8.1 Regulating the Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.9 SewingArm............................................... 21

2.9.1 Position of the Sewing Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.9.2 End Position Dampening of the Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.9.3 Timing of the Operation of the Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.10 Adjustment Screws for the Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3. Thread Trimmer ............................................ 25

3.1 FunctionSequence .......................................... 25

3.2 Position of the Base Plate and the Guide Curve . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.3 Clearance between the Drive Segment and Guide Curve . . . . . . . . . . . . . . . . . . . . . 27

3.4 Counter Knife and Thread Pull Knife . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.5 Counter Knife Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4. Clamping Table ............................................ 30

4.1 LargeGuideCurve........................................... 30

4.1.1 Attaching the Aluminium Strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.2 Changing the Stitch Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Home

Contents Page:

4.3 SmallGuideCurves ......................................... 33

4.3.1 Function of the Guide Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4.3.2 Position the Guide Curves on the Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4.3.3 Position of the Aluminium Strips on the Guide Curve . . . . . . . . . . . . . . . . . . . . . . . 35

4.4 SwitchingDisks............................................ 36

4.4.1 Function of the Switching Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4.4.2 Position of the Switching Disks on the Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

4.5 Position of the Clamping Tablees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.6 FixedClamp.............................................. 39

4.7 SwingClamps............................................. 41

4.7.1 Renewing the Coatings on the Swing Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4.8 InteriorSlides ............................................. 44

4.8.1 Setting the Interior Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4.9 SideSlides .............................................. 47

4.10 Outer Forward Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4.11 Center Forward Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4.12 InnerForwardSlide.......................................... 50

4.13 Hold-down............................................... 52

5. Causes of Unequal Edge Intervals ................................ 53

6. Synchronizer ............................................. 55

7. Pneumatics .............................................. 56

8. Maintenance ............................................. 57

1. General

These Service Instructions for the 975 - 1 - 5 describe the settings for

the sewing unit.

ATTENTION

The tasks described in the Service Instructions may only be carried

out by specialists or appropriately trained personnel !

Caution Risk of Injury

During repair, conversion and maintenance work turn the main switch

off.

Adjustment work and function testing with the machine running may

only be conducted with greatest caution under strictest observence of

all safety measures.

Product specificaties

Merk:	Durkopp Adler
Categorie:	Naaimachine
Model:	975

Heb je hulp nodig?

Als je hulp nodig hebt met Durkopp Adler 975 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Naaimachine Durkopp Adler

Durkopp Adler 20 Handleiding

17 Juni 2024

Durkopp Adler 68 Handleiding

17 Juni 2024

Durkopp Adler 743-221-01 Handleiding

16 April 2024

Durkopp Adler 2112-7 Handleiding

18 December 2023

Durkopp Adler 1967 Handleiding

20 Maart 2023

Durkopp Adler 1365-5 Handleiding

20 Maart 2023

Durkopp Adler 557 Handleiding

20 Maart 2023

Durkopp Adler D669 e-con Handleiding

30 Juni 2023

Durkopp Adler 251-140042 Handleiding

20 Maart 2023

Durkopp Adler 267 - 2016 Handleiding

20 Maart 2023

Handleiding Naaimachine

Nieuwste handleidingen voor Naaimachine

Singer Athena 2009 Handleiding

21 December 2024

Singer White 1409 Handleiding

20 December 2024

Singer Futura Quintet 5 Handleiding

20 December 2024

Singer 321C Handleiding

20 December 2024

Singer 321D Handleiding

20 December 2024

Singer 16 Handleiding

20 December 2024

Singer 251D Handleiding

20 December 2024

Singer 10 Handleiding

20 December 2024

Singer Professional Steam Press Handleiding

20 December 2024

Singer TinyTailor TT700 Handleiding

20 December 2024