Durkopp Adler 567 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Durkopp Adler 567 (80 pagina's) in de categorie Naaimachine. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/80
567 classic
Service manual
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG - 2015
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP TO CONSULT LATER
Content
Service manual 567 classic - 01.0 - 10/2015 1
1 About these Service Instructions.............................................. 3
1.1 Scope ........................................................................................... 3
1.2 Representation conventions – symbols and characters ............... 3
1.3 Other documents .......................................................................... 4
1.4 Liability.......................................................................................... 4
2 Safety information ...................................................................... 5
2.1 Basic safety instructions ............................................................... 5
2.2 Signal words and symbols used in warnings................................ 6
3 Working basis ............................................................................. 9
3.1 Sequence of the settings .............................................................. 9
3.2 Cable routing ................................................................................ 9
3.3 Removing the covers.................................................................. 10
3.3.1 Access to the machine bottom section ....................................... 10
3.3.2 Removing and fitting the arm cover............................................ 11
3.3.3 Removing and fitting the head cover .......................................... 12
3.3.4 Removing and fitting the valve cover.......................................... 12
3.3.5 Opening and closing the throat plate slide ................................. 13
3.3.6 Removing and installing the throat plate .................................... 14
3.3.7 Removing and installing the feed-dog ........................................ 15
3.4 Flats on shafts ............................................................................ 16
3.5 Locking the sewing machine in place ......................................... 16
3.6 Putting the handwheel into position............................................ 17
4 Setting the handwheel scale ................................................... 19
5 Positioning the arm shaft......................................................... 20
6 Positioning the toothed belt pulleys....................................... 21
6.1 Upper toothed belt pulley............................................................ 21
6.2 Lower toothed belt pulley............................................................ 22
7 Setting the stitch length adjusting wheel............................... 23
8 Setting the stitch length limit .................................................. 25
8.1 Setting the eccentric for the forward and backward stitches ...... 26
9 Setting the feed-dog................................................................. 27
9.1 Setting the feed-dog position...................................................... 27
9.1.1 Moving the feed-dog................................................................... 28
9.1.2 Moving the feed-dog carrier........................................................ 29
9.2 Setting the feed-dog movement ................................................. 30
9.2.1 Setting the feed movement......................................................... 30
9.2.2 Setting the feed-dog height in the top dead center..................... 31
9.2.3 Setting the stroke movement...................................................... 32
10 Aligning the needle bar linkage............................................... 33
10.1 Moving the needle bar linkage sideways.................................... 33
10.2 Aligning the needle bar linkage in the sewing direction.............. 34
11 Position of the hook and needle ............................................. 36
11.1 Setting the hook side clearance ................................................. 36
11.2 Setting the loop stroke position .................................................. 38


Product specificaties

Merk: Durkopp Adler
Categorie: Naaimachine
Model: 567

Heb je hulp nodig?

Als je hulp nodig hebt met Durkopp Adler 567 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Naaimachine Durkopp Adler

Handleiding Naaimachine

Nieuwste handleidingen voor Naaimachine