Dual MGH17BT Handleiding

Dual Radio MGH17BT

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Dual MGH17BT (31 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/31
INSTALLATION/OWNER'Sā€ˆMANUAL
AM/FMā€ˆGaugeā€ˆHoleā€ˆReceiver
MGH17BT
Front and Rear Inputs
2
MGH17BTā€ˆINSTALLATION
Mounting
Please read entire manual before installation.
Beforeā€ˆYouā€ˆStart
ā€¢ Disconnect negative battery terminal. Consult a qualified technician for instructions.
ā€¢ Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Gettingā€ˆStarted
ā€¢ Once a suitable location has been determined, drill the hole and secure the stereo
using the metal mounting bracket. If the bracket needs to be shortened, remove the
appropriate number of breakaway segments using a pair of pliers.
Fuse:
When replacing the fuse, make sure
new fuse is the correct type and
amperage. Using an incorrect fuse
could damage the radio.
Tip:
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.
Breakā€ˆLines
Color Connection
Red 12V Ignition / Accessory
Black Ground
Blue Remote Turn-on B (+)
Grey Right Front (+)
Grey/Black Right Front (-)
White Left Front (+)
White/Black Left Front (-)
Violet Right Rear (+)
Violet/Black Right Rear (-)
Green Left Rear (+)
Green/Black Left Rear (-)
Yellow Camera Input (RCA)
3
MGH17BTā€ˆINSTALLATIONā€ˆ
Mountingā€ˆtheā€ˆRadio
1. Choose a mounting location on the dash board or instrument panel that will
allow room behind to run radio cables to the power source. Consider how you will use
the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables
to an accessible area.
2. Cut a hole in the dash board using the template provided in the back of this manual. At
least 3 3/4ā€ depth is needed to mount the radio.
IMPORTANT!ā€ˆDoā€ˆnotā€ˆmountā€ˆthisā€ˆunitā€ˆwhereā€ˆitā€ˆcanā€ˆbeā€ˆsubmergedā€ˆinā€ˆwater.
3. Slide the included spring washers (B) over the screw posts (A) and attach the screw
posts to the back of the radio.
4. Place the radio in front of the dashboard opening so the wiring can be brought through
the opening.
5. After completing the wiring connections, turn the radio on to confirm operation (vehicle
accessory switch must be on). If the radio does not operate, recheck all wiring until the
problem is corrected. Once proper operation is achieved, turn the accessory switch off
and proceed with final mounting of the radio. Refer to the ā€œWiring Diagramā€ on page 5.
NOTE: Before final installation, test the wiring connections to make sure the unit is con-
nected properly and the system works.
6. Insert the radio into the mounting hole.
7. Place the ā€œUā€ bracket (C) over the screw posts and secure the radio to the dash using
the included hex nuts (D). If necessary, cut the score marks (E) on either side of the
mounting bracket to custom fit the bracket length for your application. See Figure A.
A
C
D
E
B
3 Inch Hole
Installation


Product specificaties

Merk: Dual
Categorie: Radio
Model: MGH17BT

Heb je hulp nodig?

Als je hulp nodig hebt met Dual MGH17BT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Radio Dual

Handleiding Radio

Nieuwste handleidingen voor Radio