Dormakaba RTS88 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RTS88 (10 pagina's) in de categorie Deurdranger. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
Floating Headers - 4-1/8”, 4-1/2”, 6
with RTS88 and PT21 for double doors ONLY
Installation instructions
933842 – 10-2018
| | EN
2Floating Headers 10-2018933842
Table of Contents
dormakaba Floating Headers 4-1/8“, 4-1/2“, 6“ RTS88 and PT21
Installation Instructions
Table of contents
1  Technical specifications 3
1.1 Overview 3
1.1.1 General information 3
1.1.2 Intended use 3
1.1.3 Glass requirements/fittings/mounting 3
1.1.4 Requirements for glass panel 3
1.1.5 Safety instructions 3
1.1.6 Symbols used - Safety/Installation 3
1.1.7 Maintenance, care, repair 3
1.1.8 Disposal 3
1.2 Tempered laminate glass (TLG) and adhesive
specifications 4
2 Installation instructions 5
2.1 Remove fasteners and covers 5
2.2 Disassemble floating header blocks 6
2.3 Reinstall glass grommets, blocks and fasteners 6
2.4 OPTIONAL: Apply adhesive:
(For TLG applications) 7
2.5 Install floating header extrusion 8
2.6 Install block fasteners and covers 8
2.7 RTS88 adjustments 9
2.8 PT21 adjustments 9
dormakaba Floating Headers 4-1/8“, 4-1/2“, 6“ RTS88 and PT21
Installation Instructions
10-2018933842 3
Technical specifications
Floating Headers
1.1 Overview
These instructions are for installation of 4-1/8”, 4-1/2”,
and 6” floating headers for the following mounting and
style versions:
1. Glass mounting
1.1.1 General information
dormakaba requires use of tempered laminated
and tempered monolithic glass.
dormakaba glass hardware is not suitable for
application in rooms where chemicals (e.g. chlorine)
are used such as indoor swimming pools, saunas, or
salt-water pools.
Do not swing doors with excessive force. Install
limiting stop to prevent door from opening too far.
1.1.2 Intended use
To house the RTS overhead concealed closers and
PT21 top walking beam pivots together.
1.1.3 Glass requirements/fittings/mounting
The substructure/wall must be able to bear
permanent loads, be level (max. tolerance: 1/16”
[2] per 39” [1m]).
Fasteners must be sufficiently dimensioned for the
substructure/wall and weight of the door.
When adjusting glass elements, always stick to the
required clearance for the respective hardware.
Adjust clearance so glass does not come in contact
with any hard surfaces such as glass, metal or
concrete.
Do not use excessive force when installing the glass
(avoid over tightening screws.)
1.1.4 Requirements for glass panel
dormakaba requires use of fully tempered glass,
which complies with ASTM C 1036 and ASTM C
1048. Secondary heat soaking processes are
optional but not required. This applies to both
tempered monolithic and tempered laminated
glass.
Clamping area must be flat and uncoated (no
self-cleaning coating!)
Never use glass with conchoidal fractures and/or
damaged edges.
1.1.5 Safety instructions
Installation requires two people.
Always wear protective clothing.
Only properly qualified and specially trained staff is
authorized to mount dormakaba glass hardware.
Due to crushing hazards and possible injury caused
by breakage of glass during mounting,
corresponding protective clothing (especially gloves
and protective goggles) is required.
Never clamp metal glass fitting hardware directly
to glass surface.
1.1.6 Symbols used - Safety/Installation
CAUTION
Mounting components must meet the
requirements of substructure/wall and door
weight. Please read the technical information
for fittings.
WARNING
Risk of breaking glass.
TIPS AND RECOMMENDATIONS
Universal PT21 pin diameter: 5/8” [15]
MUNDUS PT21 pin diameter: 9/16” [14]
1.1.7 Maintenance, care, repair
Immediately replace damaged parts.
Always use original dormakaba parts.
Clean clamping area with alcohol-based standard
commercial cleaning agent before mounting the
glass hardware.
Use a damp clothe for occasional cleaning,
especially the track.
Always use silicone - and oil-free cleaners (e.g.
acetone).
Check glass hardware at regular intervals for
proper positioning, smooth operation and correct
adjustment.
High traffic door systems require inspection by
properly qualified staff (specialized companies or
installation firms.)
1.1.8 Disposal
Disposal in accordance with local, state and national
regulations.
1  Technical specifications
dormakaba Floating Headers 4-1/8“, 4-1/2“, 6“ RTS88 and PT21
Installation Instructions
10-2018933842
4
Technical specifications
Floating Headers
1.2 Tempered laminate glass (TLG) and adhesive specifications
Fig. 1
NOTE: Glass should not be installed until the full cure
time as been reached (see chart above).
Important safety-related information for the mounting
and use of dormakaba glass hardware.
Required parts for laminate glass
(not included)
Part Number Quantity Usage
recommendation
3M™ Scotch-Weld™ Urethane
Adhesive, DP 605 NS
934.800 1 tube per 4 roller 1 tube
carriers
3M™ Scotch-Weld™ EPX™ Plus II
Applicator with 1:1 Plunger 2
934.801 1 applicator 1:1 plunger with
934.800 adhesive
3M™ Scotch-Weld™ EPX™ Plus II
Mixing Square Nozzle, 5.3mm 3
934.805 4 nozzles per 1 tube Pk of 4
of adhesive
Handling time frame Function Time
Working life
(time between
application and clamping of carrier)
5 minutes @ 75°F
Handling strength 20 minutes @ 73°F or more
Full cure time
(normal door usage
not recommended until full cure time
as been met)
48 hours @ 73°F or more
1.2.1 Clean clamping area with alcohol-based
standard commercial cleaning agent before
mounting the glass hardware.
1.2.2 Never clamp metal glass fitting hardware
directly to glass surface.
1.2.3 Never use clamping product on surfaces with
self-cleaning coatings.
2 Scotch-Weld™ EPX™ Plus II Applicator with 1:1 Plunger is a trademark of 3M.
3 Scotch-Weld™ EPX™ Plus II Mixing Square Nozzle is a trademark of 3M.
dormakaba Floating Headers 4-1/8“, 4-1/2“, 6“ RTS88 and PT21
Installation Instructions
10-2018933842 5
Disassemble RTS88 and PT21
Floating Headers
2.1 Remove fasteners and covers
2 Installation instructions
Fig. 2
Covers
Block
fasteners
Header
extrusion
Blocks
2.1.1 Separate cover and blocks from header extrusion.
Finish
plugs
End
caps
Universal PT21 pivot pin MUNDUS PT21 pivot pin
5/8”
[15]
9/16”
[14]
dormakaba Floating Headers 4-1/8“, 4-1/2“, 6“ RTS88 and PT21
Installation Instructions
10-2018933842
6
Disassembly blocks
Install blocks
Floating Headers
2.2.1 Disassemble fasteners and glass grommets from
both header blocks.
2.2 Disassemble floating header blocks
2.3 Install glass grommets, blocks and fasteners
2.3.1 Install glass grommets.
2.3.2 Install blocks and fasteners. Hand tight only.
2.3.3 Using a level, ensure both blocks are properly
level.
2.3.4 Fully tighten fasteners to 15ft lbs [20Nm].
Fig. 3
Fig. 4
Glass
grommets
(Fixed panel)
Fasteners Blocks
Fasteners
Glass
grommets
Fasteners
Glass
grommets
Hex key size
1/4”
(Fixed panel)(Fixed panel)(Fixed panel)
Hex key size
1/4”
Torque
15ft lbs
[20Nm]
dormakaba Floating Headers 4-1/8“, 4-1/2“, 6“ RTS88 and PT21
Installation Instructions
10-2018933842
8
Secure headers
Covers
Floating Headers
2.5 Install floating header extrusion
Fig. 6
2.6 Install block fasteners and covers
2.6.1 Secure block fasteners through top of floating
header extrusion.
2.6.2 Install covers.
2.6.3 Spray U-channel gaskets with water.
2.6.4 If applicable, tip transom glass panel up into
appropriate ceiling mounting track.
2.6.5 Lower down into U-channel on header.
2.6.6 Install end caps to pre-cleaned header/blocks.
Adhere with pre-attached double-sided tape.
2.6.7 Press finish plugs into header extrusion.
Fig. 7
(Fixed panel) Covers
Block
fasteners
U-channel
(Transom)
2.5.1 Insert setting blocks into U-channel.
2.5.2 Secure U-channel end caps prior to installing
header.
2.5.3 Lay floating header extrusion assembly down
onto level blocks.
NOTE: Double-check to ensure header is level.
2.5.4 Adjust header if necessary via fasteners and
retighten to 15 ft lbs [20Nm].
(see steps 2.3 for reference.)
End
caps
Finish
plugs
NOTE: INTERIOR VIEWS SHOWN
(Fixed panel) (Fixed panel)
(Fixed panel) (Fixed panel)
(Fixed panel)(Fixed panel)
(Fixed panel)
U-channel
Blocks


Product specificaties

Merk: Dormakaba
Categorie: Deurdranger
Model: RTS88

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RTS88 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden