Digitus 1000Base-T Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Digitus 1000Base-T (3 pagina's) in de categorie Audio/video-converter. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Gigabit Fiber Ethernet Converter
10/100/1000Base-T/TX to 1000Base-SX/LX
User’s Manual
Overview
Gigabit fiber media converter is a 10/100/1000 auto negotiating media converter. The copper port
auto negotiates the connected device’s speed and duplex mode: 10/100/1000Mbps half duplex;
or 10/100/1000 Mbps full duplex; the fiber port always operates at 1000Mbps. The maximum
distance is Multi-mode 0.5 or 2km and single-mode 10/20/40/60km or 80km.
Installation
1. Interface
RJ-45 interface
The transmission media adopts CAT5 twisted-pair with typical length of 100 meter.
It features the function of automatically identifying the through line and cross wire
Fiber interface
Fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the
two sets of optical transceiver are interfaced or connected to switch with fiber interface, the
fiber is in cross connection, namely "TX-RX", "RX-TX" (direct butting for single optical fiber).
2. Connection
The network device (work station, hub or switch is connected to RJ-45 ) with RJ-45 interface
jack of the media converter through twisted-pair. The fiber device is connected to fiber
interface of the media converter. Then switch on. The corresponding LED is on for correct
connection. (See the table below for the LED indicator lamp)
Table 1 : Front panel for single fiber media converter
Table 2 : Front panel for dual fiber media converter
Explanation for LED indicator
LED indicator serve as device monitoring and trouble display.
The following is the explanation for each LED indicator lamp.
LED Status Function Describing
PWR Power LED ON Power is ON.
OFF Power is Fail.
FX Fiber port signal
detect LED
ON Laser is receiving.
OFF No laser input.
FX-LINK/ACT Fiber port link/action
status LED
ON Fiber link is ok.
Blink Data is been received
or transmitted.
OFF Fiber link is fail.
1000M UTP port speed LED ON 1000M speed
OFF 100M speed
TX-LINK/ACT UTP port link/action
status LED
ON Link is ok.
Blink Data is been received
or transmitted.
OFF Fiber link is fail.
FDX/COL UTP port duplex LED ON Full duplex
OFF Half Duplex
Technical parameters:
1. Standard Protocol:
IEEE802.3 10 Base-T standard
IEEE 802.3u 100Base-TX/FX standard
IEEE 802.3z 1000Base-TX/FX standard
2. Connector: one UTP RJ-45connector,one SC/ST connector
3. Operation mode: full duplex mode or half duplex mode
4. Environmental temperature: 0℃-60 ℃
5. Relative humidity: 5%-90%
6. TP cable: Cat5 UTP cable
7. Transfer fiber:
multi-mode: 50/125, 62.5/125 or 100/140μm
single mode:: 8.3/125, 8.7/125, 9/125 or 10/125μm
8. Max. 2M buffer memory built in chip
9. Automatic identification of MDI/MDI-X cross line
10. High-performance 1.4Gbps memory bandwidth.
Cautions:
1. This product is suitable for indoor application.
2. Put on the dust cover of fiber interface when not used.
3. It is forbidden to stare at the TX fiber-transfer end with naked eyes.
4. Single optical fiber transceiver must be used in scription in delivery). pair (See the attachment de
Trouble shooting:
1. Device is not matched. Please select the corresponding network device according to the transfer rate of
the product (10Mbps or 100Mbps) when connected to other network devices (network card, hub, switch).
2. Line loss is excessive during the fiber wiring. Excessive loss in connector plug-in and fiber soldering
welding, and excessive intermediate nodes may cause excessive loss rate or abnormal operation.


Product specificaties

Merk: Digitus
Categorie: Audio/video-converter
Model: 1000Base-T

Heb je hulp nodig?

Als je hulp nodig hebt met Digitus 1000Base-T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Audio/video-converter Digitus

Handleiding Audio/video-converter

Nieuwste handleidingen voor Audio/video-converter