DeWalt DWMIIIFS Handleiding
DeWalt
Nietmachine
DWMIIIFS
Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt DWMIIIFS (36 pagina's) in de categorie Nietmachine. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/36
DWMIIIFS
Hardwood Flooring Tool
Outil pour parquet en bois dur
Herramienta para revestimiento
de piso de madera dura
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D
e
WALT • www.dewalt.com
Page Size: 8.5 x 5.5"
2- ENG
Table of Contents
Safety Instructions ......................................................................3
Operation....................................................................................5
Maintaince ..................................................................................7
Trouble Shooting Guide ............................................................10
Français ....................................................................................12
Español ....................................................................................24
WARNING: BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD
STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY
WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE
TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT
YOUR D
e
WALT REPRESENTATIVE OR DISTRIBUTOR.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not
avoided, .will result in death or serious injury
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice which, if not not related to personal injury
avoided, may result in property damage.
Introduction
D
e
WALT tools are precision-built tools, designed for precise, high volume nailing. These
tools will deliver efficient, dependable service when used correctly and with care. As
with any fine power tool, for best performance the manufacturer’s instructions must be
followed. Please study this manual before operating the tool and understand the safety
warnings and cautions. The instructions on installation, operation and maintenance
should be read carefully, and the manual kept for reference. Additional safety NOTE:
measures may be required because of your particular application of the tool. Contact
your D
e
WALT representative or distributor with any questions concerning the tool and
its use. D
e
WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
e
WALT (1-800-433-9258) or visit our website www.dewalt.com.
NOTE: D
e
WALT tools have been engineered to provide excellent customer satisfaction
and are designed to achieve maximum performance when used with fasteners
engineered to the same exacting standards. D
e
WALT cannot assume responsibility for
product performance if our tools are used with fasteners or accessories not meeting
the specific requirements established for fasteners, staples and accessories.
3- ENG
INTENDED USE
This DWMIIIFS Flooring Tool is intended for use by construction professionals for
installing unfinished hardwood flooring.
Precautions Regarding Use of this Tool to Install Prefinished Flooring
It may also be used to install prefinished wood flooring materials, however precautions
must be taken to assure that the finish will not be damaged by the tool. Before using the
tool on prefinished material, test a sample section to assure that the tool and installation
technique does not leave marks on the finish. This procedure must be followed for every
installation due to variations in flooring materials and condition of the tool.
Do not discharge fasteners into open air, concrete, stone, or any other material too
hard for the fastener to penetrate. Use of this tool by inexperienced operators must be
supervised.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California to
cause cancer, birth defects and other reproductive harm. Some examples of these
chemicals are lead from lead-based paints, crystalline silica from bricks and cement
and other masonry products , and arsenic and chromium from chemically treated
lumber.
Your risk from exposure varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals, work in a well-ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles."
SAFETY INSTRUCTIONS
WARNING: EYE PROTECTION which conforms to ANSI specifications
and provides protection against flying particles both from the FRONT
and SIDE should ALWAYS be worn by the operator and others in the
work area when connecting to air supply, loading, operating or servicing
this tool. Eye protection is required to guard against flying fasteners and
debris, which could cause severe eye injury.
The employer and/or user must ensure that proper eye protection is
worn. Eye protection equipment must conform to the requirements of
the American National Standards Institute, ANSI CAN/CSA Z94.3 and
provide both frontal and side protection. Non-side shielded NOTE:
spectacles and face shields alone do not provide adequate protection.
CAUTION: Additional Safety Protection will be required in some
environments. For example, the working area may include exposure to
noise level which can lead to hearing damage. The employer and user
must ensure that any necessary hearing protection is provided and
used by the operator and others in the work area. Some environments
will require the use of head protection equipment. When required, the
employer and user must ensure that head protection conforming to
ANSI CAN/CSA Z89.1 is used.
Safety Instructions - Air Supply and Connections
WARNING: Do not use oxygen, combustible gases, or bottled gases as a power
source for this tool as tool may explode, possibly causing injury.
WARNING: Do not use supply sources which can potentially exceed 200 p.s.i.g.
(14kg/cm2 ) as tool may burst, possibly causing injury.
WARNING: The connector on the tool must not hold pressure when air supply
is disconnected. If a wrong fitting is used, the tool can remain charged with air
after disconnecting and thus will be able to drive a fastener even after the air line is
disconnected possibly causing injury.
Product specificaties
| Merk: | DeWalt |
| Categorie: | Nietmachine |
| Model: | DWMIIIFS |
Heb je hulp nodig?
Als je hulp nodig hebt met DeWalt DWMIIIFS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Nietmachine DeWalt
25 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
24 Juni 2024
9 Juni 2024
9 Juni 2024
Handleiding Nietmachine
- Nietmachine Bosch
- Nietmachine Whirlpool
- Nietmachine Einhell
- Nietmachine Fellowes
- Nietmachine Gude
- Nietmachine Hikoki
- Nietmachine Hitachi
- Nietmachine Holzmann
- Nietmachine Iluv
- Nietmachine Kensington
- Nietmachine Leitz
- Nietmachine Makita
- Nietmachine Meister
- Nietmachine Metabo
- Nietmachine Milwaukee
- Nietmachine Parkside
- Nietmachine Powerfix
- Nietmachine Powerplus
- Nietmachine President
- Nietmachine Proline
- Nietmachine Ryobi
- Nietmachine Sencor
- Nietmachine Silverline
- Nietmachine Targus
- Nietmachine Topcraft
- Nietmachine Vonroc
- Nietmachine Workzone
- Nietmachine Klein Tools
- Nietmachine Rapid
- Nietmachine Genesis
- Nietmachine Fieldmann
- Nietmachine Porter-Cable
- Nietmachine Sun Joe
- Nietmachine Rapoo
- Nietmachine Dedra
- Nietmachine MSW
- Nietmachine Craftsman
- Nietmachine Surtek
- Nietmachine Rexel
- Nietmachine Swingline
- Nietmachine Aqua Joe
- Nietmachine Abac
- Nietmachine CTA Digital
- Nietmachine Meister Craft
- Nietmachine Werckmann
- Nietmachine POWERNAIL
- Nietmachine Neo
- Nietmachine Syscom
- Nietmachine Mannesmann
- Nietmachine Smart365
Nieuwste handleidingen voor Nietmachine
15 Oktober 2024
27 Augustus 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
28 Juni 2024
25 Juni 2024