DeWalt DWC860W Handleiding

DeWalt Zaagmachine DWC860W

Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt DWC860W (7 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

NOTICE: may Indicates a practice not related to personal injury which, if not avoided,

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL E

US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention while operating power tools

may result in serious personal injury.

b) Protective Use personal protective equipment. Always wear eye protection.

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench

or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) The Do not force the power tool. Use the correct power tool for your application.

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting the power tool

accidentally.

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

DWC860W

Heavy-Duty 4-3/8" (110 mm) Wet/Dry Masonry Saw

Scie industrielle à maçonnerie à sec/à l’eau de 110mm (4-3/8po)

Sierra industrial de 110 mm (4-3/8") de corte húmedo o seco para mampostería

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

, 2014 DEWALT

The following are trademarks for one or more D WALT power tools: the yellow and black color scheme, the “D” shaped E

air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on

the surface of the tool.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could

result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Cut-Off Machine Safety Warnings

a) The guard provided with the tool must be securely attached to the power tool and

positioned for maximum safety, so the least amount of wheel is exposed towards

the operator. Position yourself and bystanders away from the plane of the rotating

wheel. The guard helps to protect operator from broken wheel fragments and accidental

contact with wheel.

b) Use only continuous rim diamond cut-off wheels for your power tool. Just because

an accessory can be attached to your power tool, it does not assure safe operation.

c) The rated speed of the accessory must be at least equal to the maximum speed

marked on the power tool. Accessories running faster than their rated speed can break

and fly apart.

d) Wheels must be used only for recommended applications. For example: do not

grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may cause them to shatter.

e) Always use undamaged wheel flanges that are of correct diameter for your

selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of

wheel breakage.

f) The outside diameter and the thickness of your accessory must be within the

capacity rating of your power tool. Incorrectly sized accessories cannot be adequately

guarded or controlled.

g) The arbor size of wheels and flanges must properly fit the spindle of the power tool.

Wheels and flanges with arbor holes that do not match the mounting hardware of the power

tool, will run out of balance, vibrate excessively and may cause loss of control.

h) Do not use damaged wheels. Before each use, inspect the wheels for chips

and cracks. If power tool or wheel is dropped, inspect for damage or install an

undamaged wheel. After inspecting and installing the wheel, position yourself and

bystanders away from the plane of the rotating wheel and run the power tool at

maximum no load speed for one minute. Damaged wheels will normally break apart

during this test time.

i) Wear personal protective equipment. Depending on application, use face shield,

safety goggles or safety glasses. As appropriate, wear dust mask, hearing

protectors, gloves and shop apron capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be capable of filtrating particles

generated by your operation. Prolonged exposure to high intensity noise may cause hearing

loss.

j) Keep bystanders a safe distance away from work area. Anyone entering the work

area must wear personal protective equipment. Fragments of workpiece or of a broken

wheel may fly away and cause injury beyond immediate area of operation.

k) Hold the power tool by insulated gripping surfaces only, when performing an

operation where the cutting accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

l) Position the cord clear of the spinning accessory. If you lose control, the cord may be

cut or snagged and your hand or arm may be pulled into the spinning wheel.

m) Never lay the power tool down until the accessory has come to a complete stop.

The spinning wheel may grab the surface and pull the power tool out of your control.

n) Do not run the power tool while carrying it at your side. Accidental contact with the

spinning accessory could snag your clothing, pulling the accessory into your body.

o) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the

housing and excessive accumulation of powdered metal may cause electrical hazards.

p) Do not operate the power tool near flammable materials. Sparks could ignite these

materials.

q) The saw is intended to use 4-3/8" (111 mm) diameter continuous rim diamond

blades, 1/16" (1.6 mm) thick with a 7/8" (22.2 mm) center hole diameter. Refer to the

Accessories section for more information.

Further Safety Instructions For Abrasive Cutting-Off

Operations

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged rotating wheel. Pinching or snagging

causes rapid stalling of the rotating wheel which in turn causes the uncontrolled power tool to

be forced in the direction opposite of the wheel’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can dig into the surface of the material causing the

wheel to climb out or kick out. The wheel may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may

also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position your body and arm to allow you

to resist kickback forces. Always use auxiliary handle, if provided, for maximum

control over kickback or torque reaction during start-up. The operator can control

torque reactions or kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory. Accessory may kickback over your

hand.

c) Do not position your body in line with the rotating wheel. Kickback will propel the tool

in direction opposite to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or kickback.

e) Do not attach a saw chain, woodcarving blade, segmented diamond wheel, or

toothed saw blade. Such blades create frequent kickback and loss of control.

f) Do not jam the wheel or apply excessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to

twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

g) When wheel is binding or when interrupting a cut for any reason, switch off the

power tool and hold the power tool motionless until the wheel comes to a complete

stop. Never attempt to remove the wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and take corrective action to eliminate the

cause of wheel binding.

h) Do not restart the cutting operation in the workpiece. Let the wheel reach full

speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

i) Support panels or any oversized workpiece to minimize the risk of wheel pinching

and kickback. Large workpieces tend to sag under their own weight. Supports must be

placed under the workpiece near the line of cut and near the edge of the workpiece on both

sides of the wheel.

j) Use extra caution when making a “pocket cut” into existing walls or other blind

areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can

cause kickback.

Additional Speciﬁ c Safety Instructions for Masonry Saws

• Never hold piece being cut in your hands or across your leg. Secure the workpiece

to a stable platform. It is important to support the work properly to minimize body

exposure, blade binding, or loss of control.

• Don’t unplug if plug or receptacle is wet. Disconnect the fuse or circuit breaker that

supplies power to the tool. Then unplug and examine for presence of water in the receptacle.

• Wait for the saw to come to a complete stop. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for

the blade to stop after switch is released.

• Do not use to cut wood or metal.

DANGER: Keep hands away from cutting area and blade. Personal injury may result.

WARNING: Always plug extension cord into a GFCI protected outlet.

WARNING: To reduce the risk of electrocution, keep all connections dry and off the

ground. Do not touch plug with wet hands.

WARNING: A Ground Fault Circuit Interrupter (GFCI) is provided on the cord set. Receptacles

are available having built in GFCI protection and may be used for an added measure of safety.

When using an extension cord, always plug into a GFCI protected receptacle or outlet.

WARNING: Test GFCI before each use:

1. Plug GFCI into power outlet. Indicator should turn red.

2. Press test button. Red indicator should disappear.

3. Press reset button for use. Do not use if above test fails.

WARNING: Do not use bonded abrasive wheels with this saw. Personal injury may result.

WARNING: Never use saw with salt water or a conductive fluid.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or

long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge)

for safety. The smaller the gauge number of the wire, the greater the capacity of the cable,

that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating. When using more than one extension

to make up the total length, be sure each individual extension contains at least the minimum

wire size. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge

number, the heavier the cord.

WARNING: Always plug extension cord into a GFCI protected outlet.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V .................. volts A ...................amperes

Hz ................ hertz W .................. watts

min ..............minutes ................ alternating current

...........direct current ................ alternating or direct current

................Class I Construction no ................. no load speed

...

.........

......

...........

.....

...........

......

...... ....................(grounded) n ................... rated speed

................Class II Construction ..................earthing terminal

....................(double insulated) ..................safety alert symbol

…/min .........per minute BPM..............beats per minute

IPM ..............impacts per minute RPM ..............revolutions per minute

SPM ............strokes per minute sfpm ..............surface feet per minute

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than

10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does

not operate, check power supply.

COMPONENTS (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could

result.

A. GFCI on cord set

B. On/Off Switch

C. Lock-On button

D. Diamond blade

E. External flange

F. Clamping screw

G. Water tubing

H. Tool inlet

I. Water tubing adapter

J. Water pressure regulator (5 psi)

K. Screw

L. Water nozzle

M. Depth adjustment knob

N. Shoe

O. Water valve lever

P. Cutting guide

Q. Bevel adjustment knob

R. Brush covers

S. Brush assembly

T. Front handle

U. Main handle

V. Flange wrench

W. T-handle wrench

Switch (Fig. 1, 2)

WARNING: To avoid the possibility of the appliance plug or receptacle getting wet, position

the saw to one side of a wall mounted receptacle to prevent water from dipping onto the

receptacle or plug. The user should arrange a “drip loop” in the cord connecting the saw to a

receptacle (Fig. 2). The “drip loop” is that part of the cord below the level of the receptacle, or

the connector if an extension cord is used, to prevent water traveling along the cord and coming

in contact with the receptacle.

CAUTION: Before plugging in tool, always check to see that the switch actuates properly and

returns to the OFF position when released.

1. Depress and hold the switch (B) to start operation.

2. For continuous operation, press the lock-on button (C) and release the switch. To disengage

the locking button, depress then release the switch.

ASSEMBLY

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

To Install the Diamond Blade (Fig. 1, 3)

1. Place saw on a stable surface.

2. Place blade (D) on spindle.

3. Using the flange wrench (V) provided, hold the external flange (E)

4. Turn the clamping screw (F) counterclockwise to tighten. Use the T-handle wrench (W)

provided to secure tightly.

5. To remove the blade, reverse this procedure.

Mounting the Wet Cut System (Fig. 1)

WARNING: A Ground Fault Circuit Interrupter (GFCI) is provided on the cord set. DO NOT

use the tool if the cord set is damaged or the Ground Fault Circuit Interrupter (GFCI) fails the

before use test. Replacement of the cord set and plug should be performed by a DEWALT

factory service center, a DEWALT authorized service center, or other qualified service personnel.

Always use identical replacement parts.

WARNING: Receptacles are available having built in GFCI protection and may be used for

an added measure of safety. When using an extension cord, always plug into a GFCI protected

receptacle or outlet.

This system minimizes airborne dust particles while improving cutting quality and blade life.

1. Loosen the depth adjustment knob (M) and pull shoe (N) to it’s minimum depth of cut

position.

2. Using a screwdriver, remove the screw (K) located next to the depth adjustment knob

mounted to the casting.

3. Position the water valve assembly such that the hole in the water valve assembly aligns with

the screw hole located in the casting and the forked water valve (L) straddles the blade.

4. Secure in place with screw. DO NOT overtighten the screw; this could damage the water

valve assembly.

Water Valve Assembly (Fig. 1)

WARNING: Never use water valve assembly without a properly functioning pressure

regulator. This could cause damage to the water tubing if excessive pressure builds up.

1. Never use the saw over head. When using water, limit cutting to the horizontal position to

reduce the risk of water entering the tool.

2. Prior to using the tool with the water valve assembly, inspect water tubing (G) for holes

cracks or other damage. Replace with identical replacement parts if a potential weakened or

damaged area is found. Check connections at the tool inlet (H), water valve and adapter (I)

for leaks. If the connection is loose or the tubing is relaxed around barbs, disconnect tubing,

trim tubing back approximately 1" (25.4mm), then reconnect tubing. Ensure that tubing is

pushed all the way past the barb(s). Check to ensure tight connection.

FIG. 1

FIG. 3

FIG. 4 FIG. 5

FIG. 6 FIG. 7

FIG. 2

FIG. 8 U

3. When using the water kit, always use the water pressure regulator (J) provided. The pressure

regulator can handle up to an 80 psi water source. Firmly attach the regulator to the water

source, but do not overtighten. Be sure to use the filter washer (inside regulator intake

end) to prevent contaminates from clogging water jet ports. If regulator is lost or damaged,

replace with identical replacement parts.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

WARNING: Use the appropriate blade. Do not use cracked, damaged or excessively worn

blades. Do not use to cut wood or metal.

CAUTION: Wait for the blade to reach the maximum speed and use a slow even feed for

proper cutting.

CAUTION: The DWC860W should only be used on horizontal surfaces (see Water Valve

Assembly).

CAUTION: Use clamps or other practical way to secure and support the workpiece to a

stable platform. Holding the work by your hand or against your body is unstable and may lead

to loss of control.

Proper Hand Position (Fig. 8)

WARNING: To reduce the risk of serious personal injury, Always use proper hand position

as shown.

WARNING: To reduce the risk of serious personal injury, always hold securely in anticipation

of a sudden reaction.

Proper hand position requires one hand on the main handle (U) and the other hand on the front

handle (T) as shown.

NOTE: Figure 8 shows the proper hand positon for a left-handed person. For a right-handed

person, reverse the hand positions.

Depth of Cut Adjustment (Fig. 4)

1. Loosen the depth adjustment knob (M) to release.

2. Move the shoe (N) up or down to desired position.

3. Tighten the depth adjustment knob.

WET CUT METHOD (FIG. 1, 4)

WARNING: A Ground Fault Circuit Interrupter (GFCI) is provided on the cord set. DO NOT

use the tool if the cord set is damaged or the Ground Fault Circuit Interrupter (GFCI) fails the

before use test. Replacement of the cord set and plug should be performed by a DEWALT

factory service center, a DEWALT authorized service center, or other qualified service personnel.

Always use identical replacement parts.

WARNING: Receptacles are available having built in GFCI protection and may be used for

an added measure of safety. When using an extension cord, always plug into a GFCI protected

receptacle or outlet.

WARNING: Test GFCI before each use:

1. Plug GFCI into power outlet. Indicator should turn red.

2. Press test button. Red indicator should disappear.

3. Press reset button for use. Do not use if above test fails.

WARNING: To reduce the risk of electric shock, ensure water will not enter into your tool. Do

not touch plug with wet hands.

1. Follow the instructions described under Mounting the Wet Cut System.

2. To regulate the water flow, open the water valve by pivoting the lever (O) away from the unit.

3. To close water valve, push the lever toward the unit.

4. Proceed as described below for straight or angled cuts.

STRAIGHT CUTS (FIG. 1)

1. Using a marker or grease pencil, mark the area to be cut.

2. Place the shoe of the saw on the workpiece ensuring that the blade does not touch the

workpiece.

3. Align the external part of the cutting guide (P) with the cut outline on the workpiece.

4. Turn the tool on and wait for the blade to reach its maximum velocity.

5. Move the tool slowly and evenly forward, following the cut line.

ANGLED CUTS (FIG. 1, 5)

1. Using a marker or grease pencil, mark the area to be cut.

2. Release the bevel adjustment knob (Q) and move it to the desired angle.

3. After selecting the desired angle, tighten the knob to secure the shoe.

4. Align the internal part of the cutting guide (P) with the cut line on the workpiece.

5. Turn the tool on and wait for the blade to reach its maximum velocity.

6. Move the tool slowly and evenly forward, following the cut line.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Brushes (Fig. 6, 7)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect

tool from power source before making any adjustments or removing/installing

attachments or accessories.

Inspect carbon brushes regularly by unplugging tool, removing the brush covers (R) and with-

drawing the brush assemblies (S).

Keep brushes clean and sliding freely in their guides. Always replace the brush in the same

orientation in the holder as the used brush was prior to its removal. Carbon brushes have varying

symbols stamped into their sides, and if the brush is worn down to the line closest to the spring,

brushes must be replaced. Use only identical DEWALT brushes. Use of the correct grade of brush is

essential for proper operation. New brush assemblies are available at DEWALT service centers. The

tool should be allowed to “run in” (run at no load) for 10 minutes before use to seat new brushes.

CAUTION: While “running in,” DO NOT TIE, TAPE OR OTHERWISE LOCK THE

SWITCH ON. HOLD BY HAND ONLY.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing

this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Accessories

WARNING: Since accessories, other than those offered by D WALT, have not been tested E

with this product, use of such accessories with this tool could be hazardous. To reduce the risk of

injury, only DEWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer

or authorized service center. If you need assistance in locating any accessory, please contact

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT

(1-800-433-9258) or visit our website: www.dewalt.com.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including

brush inspection and replacement) should be performed by a DEWALT factory service center,

a DEWALT authorized service center or other qualified service personnel. Always use identical

replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely

event a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date of purchase. This warranty does not cover part failure due to normal

wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights which vary in certain states

or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for

a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque

mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière

à ces symboles.

DANGER : indique une situation dangereuse imminente qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui,

si elle n’est pas évitée, entraîner lapourrait mort ou des blessures graves.

ATTENTION: indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, entraîner des pourrait blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de dommages corporels

mais qui par contre, si rien n’est fait pour l’éviter, poser despourrait risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE

OUTIL DEWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour les outils

électriques

AVERTISSEMENT ! Lire tous les avertissements de sécurité et toutes les

directives. Le non-respect des avertissements et des directives pourrait se solder par un

choc électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à

alimentation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel

qu’en présence de liquides, de gaz ou de poussières inflammables. Les outils

électriques produisent des étincelles qui pourraient enflammer la poussière ou les

vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un

outil électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais

modifier la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation

avec un outil électrique mis à la terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des

tuyaux, des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc

électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de

l’eau dans un outil électrique augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de

la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur

réduira les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés

d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un

outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue

ou sous l’influence de drogues, d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut entraîner des blessures corporelles

graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une

protection oculaire. L’utilisation d’équipements de protection comme un masque

antipoussière, des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les risques de blessures

corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve

à la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou

d’insérer un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil

électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique

dont l’interrupteur est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une

clé de réglage attachée à une partie pivotante de l’outil électrique peut provoquer des

blessures corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de

bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces

mobiles. Les vêtements amples, les bijoux ou les cheveux longs risquent de rester

coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de

dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés

et utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers

engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à

l’application. L’outil électrique approprié effectuera un meilleur travail, de façon plus

sûre et à la vitesse pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de

ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel

de l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à

aucune personne n’étant pas familière avec un outil électrique ou son mode

d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les

mains d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées

ou coincées, si des pièces sont brisées ou présentent toute autre condition

susceptible de nuire au bon fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant toute nouvelle utilisation.

Beaucoup d’accidents sont causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe

bien entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à

maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail

à effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour

laquelle il a été conçu est dangereuse.

5) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant

que des pièces de rechange identiques. Cela permettra de maintenir une utilisation

sécuritaire de l’outil électrique.

Consignes de sécurité propres aux machines à

découper

a) Le carter de protection fourni avec l’outil doit être solidement fixé à l’outil

électrique et positionné pour optimiser la sécurité pour que l’utilisateur soit le

moins possible exposé à la meule. Se positionner, ainsi que tout tiers présent,

hors du plan de rotation de la meule. Le carter aide à protéger l’utilisateur contre toute

projection de fragments et contre tout contact avec la meule.

b) Utiliser exclusivement des meules diamant circulaires avec cet outil électrique.

Le fait qu’un accessoire peut être connecté à l’outil ne veut pas automatiquement dire que

son utilisation ne posera aucun risque.

c) La vitesse nominale des accessoires utilisés doit être équivalente ou supérieure

à la vitesse maximale apposée sur l’outil. Les accessoires utilisés à une vitesse

supérieure à leur vitesse nominale peuvent éclater ou se détacher de l’outil.

d) Les meules ne doivent être utilisées que pour les applications recommandées.

Par exemple: ne pas meuler avec la partie latérale d’une meule à tronçonner. Les

meules à tronçonner ont été conçues pour le meulage périphérique, toute force latérale

appliquée sur ces meules pourrait les faire éclater.

e) Utiliser systématiquement des brides de meules en parfait état, du diamètre

adapté à la meule choisie. Les brides de meules servent de support aux meules,

réduisant ainsi les possibilités que la meule se brise.

f) Le diamètre externe et l’épaisseur de l’accessoire utilisé doivent se conformer

aux spécifications de la plaque signalétique de l’outil électrique. Les accessoires

aux spécifications incorrectes ne peuvent être ni maintenus ni contrôlés de façon adéquate.

g) L’alésage des meules et brides doit correspondre parfaitement à la taille de la

broche de l’outil électrique. Les meules et brides dont l’alésage ne correspond pas au

dispositif d’installation de l’outil électrique ne tourneront pas correctement, vibreront de

façon excessive et pourront causer la perte de contrôle de l’outil.

h) Ne pas utiliser de meules endommagées. Avant chaque utilisation, vérifier que les

meules ne comportent aucune fissure ou craquelure. En cas de chute de l’outil

électrique ou de la meule, vérifier les dommages ou remplacer la meule par une

neuve. Après avoir inspecté et installé une meule, se positionner, soi-même et

tout individu présent, hors du plan de rotation de la meule et laisser tourner l’outil

une minute à sa vitesse à vide maximale. En général, les meules endommagées se

brisent pendant ce temps d’essai.

i) Porter un équipement individuel de protection. Utiliser une protection faciale et

des lunettes ou un masque de protection. Si approprié, porter un masque anti-

poussières, une protection auditive, des gants et un tablier d’atelier capables de

vous protéger contre toute projection abrasive ou tout fragment. La protection

oculaire doit pouvoir arrêter toute projection de débris engendrés par des opérations

diverses. Le masque anti-poussières, ou l’appareil de protection des voies respiratoires

doit pouvoir filtrer les particules engendrées par l’opération en cours. Toute exposition

prolongée à un haut niveau de décibels peut occasionner une perte de l’acuité auditive.

j) Maintenir à distance toute personne étrangère au travail en cours. Toute

personne à l’intérieur de l’aire de travail doit porter un équipement individuel de

protection. Des débris provenant de la pièce à travailler ou d’une meule endommagée

pourraient être éjectés et causer des dommages corporels au-delà de l’aire de travail

immédiate.

k) Tenir l’outil électrique par les surfaces isolées prévues à cet effet pendant

toute utilisation où l’organe de coupe pourrait entrer en contact avec des fils

Product specificaties

Merk:	DeWalt
Categorie:	Zaagmachine
Model:	DWC860W

Heb je hulp nodig?

Als je hulp nodig hebt met DeWalt DWC860W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine DeWalt

DeWalt DW861 Handleiding

11 September 2024

DeWalt DCS397 Handleiding

15 Juli 2024

DeWalt DCS778 Handleiding

15 Juli 2024

DeWalt DWE249 Handleiding

15 Juli 2024

DeWalt DCMCS574 Handleiding

12 Juni 2024

DeWalt DAH180032 Handleiding

11 Juni 2024

DeWalt DCS378 Handleiding

9 Juni 2024

DeWalt DCS573 Handleiding

3 Juli 2023

DeWalt DCCS623 Handleiding

30 Juni 2023

DeWalt DC310K Handleiding

16 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Makita DJR187ZK Handleiding

2 December 2024

Fieldmann FDK 201302-E Handleiding

1 December 2024

Fieldmann FDP 200805-E Handleiding

1 December 2024

Fieldmann FZP 4216-B Handleiding

1 December 2024

Fieldmann FZP 5816-B Handleiding

1 December 2024

King Craft ZKGS 4300 UG Handleiding

30 November 2024

Global PSG 750 Handleiding

30 November 2024

Global MTS-G 400 Handleiding

30 November 2024

Global N-PSL 750 Handleiding

30 November 2024

Global PSL-G 750 Handleiding

30 November 2024