DeWalt DW311K Handleiding

DeWalt Zaagmachine DW311K

Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt DW311K (23 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/23

DW310, DW311

VS Reciprocating Saws

Scies alternatives à vitesse variable

Sierras alternativas de velocidad variable

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: will Indicates an imminently hazardous situation which, if not avoided,

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

NOTICE: may Indicates a practice which, if not avoided, not related to personal injury

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DeWALT TOOL, CALL

US TOLL FREE AT: 1-800-4-DeWALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) The Do not force the power tool. Use the correct power tool for your application.

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Speciﬁc Safety Rules

• Hold power tool by insulated gripping surfaces, when performing an operation where

the cutting accessory may contact hidden wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed metal parts of the power tool “live” and could give

the operator an electric shock.

• Use clamps or another practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body leaves it unstable and may lead to

loss of control.

• Keep hands away from moving parts. Never place your hands near the cutting area.

• Keep hands away from cutting area. When sawing, never reach underneath or behind the

material being cut for any reason.

• Never hold work in your hand, lap or against parts of your body when sawing. The saw

my slip and the blade could contact the body causing injury.

• Use extra caution when cutting overhead and pay particular attention to overhead

wires which may be hidden from view. Anticipate the path of falling branches and debris

ahead of time.

• Do not operate this tool for long periods of time. Vibration caused by the operating action

of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra

cushion, take frequent rest periods, and limit daily time of use.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long

hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the

cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions are

as follows:

.....................

volts A

.........................

amperes

Hz watts

...................

hertz W

........................

min minutes

.................

or AC alternating current .............

or DC direct current or AC/DC alternating or direct current

.....

......

...................Class I Construction n

.......................

no load speed

(grounded) n

.........................

rated speed

................... Class II Construction

.......................

earthing terminal

(double insulated) safety alert symbol ........................

…/min

............

per minute BPM beats per minute ...................

IPM

.................

impacts per minute RPM revolutions per minute ...................

SPM

...............

strokes per minute sfpm surface feet per minute

DeWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286

The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the e

“D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of

lozenge-shaped humps on the surface of the tool.

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.come

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than

10% will cause loss of power and overheating. D WALT tools are factory tested; if this tool does e

not operate, check power supply.

CAUTION: Use only on AC power supply (NOT DC).

COMPONENTS (Fig. 1, 2)

A. Trigger switch F. Blade clamp collar

B. Variable speed selector wheel (Fig. 2) G. Hand grip

C. Shoe release lever H. Rear handle

D. Adjustable shoe

E. Blade action selector (Fig. 2)

TRIGGER SWITCH

The variable speed trigger switch (A) will give you added versatility. The further the trigger is

depressed the higher the speed of the saw. To turn the tool OFF, release the trigger.

NOTE: This tool has no provision to lock the switch in the ON position, and should never be locked

ON by any other means.

CAUTION: Use of very slow speed is recommended only for begin ning a cut. Prolonged use at

very slow speed may damage your saw.

VARIABLE SPEED SWITCH AND SELECTOR WHEEL

Both saws are equipped with a variable speed control (0 to 2600 SPM). As the trigger switch is

depressed, the speed of the saw blade increases.

The DW311 has a variable speed selector wheel (B) to control the speed of the tool. To select a

slow speed for operating your saw, rotate the wheel to a low number on the dial. To select a higher

speed, rotate the wheel to a higher number.

The lower speeds are recommended for most metal cutting, while the higher speeds are

recommended for wood. A few practice cuts on scrap material at various speeds will aid you in

choosing the best speed for obtraining the desired results for your application.

Dual Blade Motion (DW311 Only) (Fig. 2)

The DW311 has dual blade motion: straight reciprocating motion or orbital motion.

Straight reciprocating motion is used for all metal cutting operations and for wood cutting

applications where finish is more important than speed. To set the saw for straight reciprocating

motion, turn the blade action selector (E) 45˚ clockwise to align the mark (I) with the arrow on the

tool (J), as shown.

Orbital motion is used for fast cutting of wood. To set the saw for orbital action, turn the blade

action selector 45˚ counterclockwise to align the mark (K) with the arrow on the tool (J), as shown.

Adjustable Shoe (Fig. 1, 3)

CAUTION: Turn off and unplug the tool before making any adjustments or removing or

installing attachments or accessories.

Push the shoe release lever (C) downward and slide the shoe (D) out to the desired setting. Rotate

the lever to lock shoe into position.

CAUTION: Cut hazard. To prevent loss of control, never use tool without shoe.

CAUTION: Risk of personal injury and property damage. Ensure the shoe is locked into position

before using tool.

ASSEMBLY

WARNING:

To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Blade Installation and Removal (Fig. 4, 5)

Different blade lengths are available. Use the appropriate blade for the application. The

blade should be longer than 3-1/2” and should extend past the shoe and the thickness of the

workpiece during the cut. Select the blade best suitable for the material to be cut and use the

shortest blade suitable for the thickness of the material. Do not use jigsaw blades with this tool.

WARNING: Cut hazard. Blade breakage may occur if the blade does not extend past the shoe

and the workpiece during the cut (Fig. 4). Increased risk of personal injury, as well as damage to

the shoe and workpiece may result.

WARNING: Cut hazard. Turn off and unplug the tool before making any adjustments or removing

or installing attachments or accessories.

TO INSTALL BLADE INTO SAW (FIG. 4, 5)

1. Point tool away from body.

2. Rotate blade clamp collar (F) to release position.

3. Insert blade shank from the front.

4. Rotate blade clamp collar to lock blade into position.

NOTE: Blade can be installed upside-down to assist in flush-to cutting, see Figure 7.

TO REMOVE BLADE FROM SAW

WARNING: Burn hazard. Do not touch the the blade immediately after use. Contact with the

blade may result in personal injury.

1. Rotate blade clamp collar (F) to release position.

2. Remove blade.

OPERATION

WARNING:

To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

WARNING: Always wear eye protection while operating this or any other power tool.

WARNING: Burn hazard. Do not touch the the blade immediately after use. Contact with the

blade may result in personal injury.

Before you begin work, ensure the material to be cut is rigid. Small workpieces should be securely

clamped to the work table.

PROPER HAND POSITION

Grasp the underside of the hand grip (G) with one hand and the rear handle (H) with the other hand.

Cutting (Fig. 6)

WARNING: Always wear eye protection while operating this power tool.

WARNING: Cut hazard. Exercise extra caution when cutting towards operator. Always hold saw

firmly with both hands while cutting.

Before cutting any type of material, be sure it is firmly anchored or clamped to prevent slipping.

Place blade lightly against work to be cut, depress the trigger switch and allow it to obtain

maximum speed before applying pressure. Whenever possible, the saw shoe must be held firmly

against the material being cut. This will prevent the saw from jumping or vibrating and minimize

blade breakage. Any cut which puts pressure on the blade, such as angle or scroll cuts, increase

potential for vibration, kickback and blade breakage.

NOTE: The blade cuts on the down stroke leaving the cleanest edge on the underside of the

material.

WARNING: Shock hazard. Use extra caution when cutting overhead and pay particular attention

to overhead wires which may be hidden from view.

WARNING: Use extra caution when cutting overhead and anticipate the path of falling

branches and debris ahead of time.

WARNING: Inspect work site for hidden gas pipes, water pipes, or electrical wires before

making blind or plunge cuts. Failure to do so may result in explosion, property damage, electric

shock, and/or serious personal injury.

FLUSH-TO CUTTING (FIG. 7)

The compact design of the saw motor housing and spindle housing permits extremely close cutting

to floors, corners and other difficult areas. The blade can be installed upside-down to assist in

flush-to cutting

POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 8)

WARNING: Shock hazard. Exercise extreme caution when blind cutting to ensure that there are

no foreign objects such as electrical wire, conduit, plumbing pipes, etc., that may come in contact

with the blade.

NOTE: DO NOT attempt to pocket/plunge cut metal.

FIG. 1

DW310

FIG. 5 FIG. 6

FIG. 7

FIG. 9

FIG. 8 STARTING POSITION FOR POCKET CUTTING

POSITION DE DÉPART POUR LA COUPE EN POCHE

POSICIÓN DE ARRANQUE PARA CORTES INTERNOS

ROCK TOOL UP TO NORMAL CUTTING POSITION

AFTER BLADE HAS CUT THROUGH MATERIAL.

BALANCER L’OUTIL JUSQU’À SA POSITION NORMALE DE

COUPE APRÈS LA PÉNÉTRATION COMPLÈTE

DE LA LAME DANS LE MATÉRIAU.

GIRE LA HERRAMIENTA HASTA LA POSICIÓN DE

CORTE NORMAL DESPUÉS DE QUE LA HOJA HAYA

CORTADO EL MATERIAL.

FIG. 3

FIG. 4

STRAIGHT

RECIP. MOTION

MOUVEMENT

ALTERNATIF VERTICAL

MOVIMIENTO

ALTERNATIVO RECTO

ORBITAL ACTION

FONCTIONNEMENT

ORBITAL

ACCIÓN ORBITAL

DW311

G E

FIG. 2

The initial step in pocket/plunge cutting is to measure the surface area to be cut and mark

clearly with a pencil, chalk or scriber. Use the appropriate blade for the application. The blade should

be longer than 3-1/2” (88.9mm) and should extend past the shoe and the thickness of the workpiece

during the cut. Insert blade in blade clamp.

Next, tip the saw backward until the back edge of the shoe is resting on the work surface and the

blade clears the work surface. Depress trigger switch to turn motor on, always permitting blade to

attain maximum speed. Grip saw steadily and begin a slow, deliberate upward swing with the handle

of the saw. Blade will begin to feed into material. Always be sure blade is completely through material

before continuing with pocket/plunge cut.

NOTE: In areas where blade visibility is limited, use the edge of the saw shoe as a guide. Lines for

any given cut should be extended beyond edge of cut to be made.

METAL CUTTING (FIG. 9)

This unit has different metal cutting capacities depending upon type of blade used and the metal

to be cut. Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials. In

thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will insure a clean

cut without excess vibration or tearing of metal. Always remember not to force cutting blade as

this reduces blade life and causes costly blade breakage. Start the cut on the surface where the

greatest number of teeth will contact the workpiece.

NOTE: It is generally recommended that when cutting metals you should spread a thin film of oil

or other lubricant along the line ahead of the saw cut for easier operation and longer blade life.

MAINTENANCE

WARNING:

To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Cleaning

WARNING:

Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing

this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Lubrication

This tool has been lubricated with a sufficient amount of high-grade lubricant for the life of this unit

under normal conditions. No further lubrication is necessary.

Brush Inspection

For your continued safety and electrical protection, brush inspection and replacement on this tool

should only be performed by a D factory service center, a DeWALT eWALT authorized service center

or other qualified service personnel.

At approximately 100 hours of use, take or send your tool to your nearest authorized service center

to be thoroughly cleaned and inspected. Have worn parts replaced and lubricated with fresh

lubricant. Have new brushes installed and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need for immediate

servicing of the tool. DO NOT CONTINUE TO OPERATE THE TOOL UNDER THIS CONDITION. If

proper operating voltage is present, return the tool for immediate service.

Accessories

WARNING:

Since accessories, other than those offered by DeWALT, have not been tested with

this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,

only DeWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer or

authorized service center. If you need assistance in locating any accessory, please contact DeW ALT

Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DeWALT (1-800-433-

9258) or visit our website: www.dewalt.com.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed by a D factory service center, a DeWALT eWALT

authorized service center or other qualified service personnel. Always use identical replacement

parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DeWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.

com or call 1-800-4-D WALT (1-800-433-9258). This warranty does not apply to accessories or e

damage caused where repairs have been made or attempted by others. This warranty gives you

specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D WALT tools are covered by our:e

1 YEAR FREE SERVICE

DeWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DeWALT Power Tool, Laser, or Nailer

for any reason, you can return it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,

call 1-800-4-DeWALT (1-800-433-9258) for a free replacement.

Déﬁnitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque

mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière

à ces symboles.

DANGER : indique une situation dangereuse imminente qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui,

si elle n’est pas évitée, entraîner lapourrait mort ou des blessures graves.

ATTENTION : indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, entraîner des pourrait blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de dommages corporels

mais qui par contre, si rien n’est fait pour l’éviter, poser despourrait risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE

OUTIL D WALT, COMPOSEZ LE NUMÉRO SANS FRAIS : e1-800-4-DeWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour les outils

électriques

AVERTISSEMENT ! Lire tous les avertissements de sécurité et toutes les directives.

Le non-respect des avertissements et des directives pourrait se solder par un choc

électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à

alimentation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil

électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais

modifier la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un

outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de

fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est

plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau

dans un outil électrique augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de

la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira

les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un

disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les

risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un

outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue

ou sous l’influence de drogues, d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des

chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la

situation le requiert réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la

position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer

un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors

que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à

la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de

réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de

mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les

pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de

dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés et

utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers engendrés

par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de

ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à

aucune personne n’étant pas familière avec un outil électrique ou son mode

d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains

d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées

ou coincées, si des pièces sont brisées ou présentent toute autre condition

susceptible de nuire au bon fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup

d’accidents sont causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à

effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle

il a été conçu est dangereuse.

5) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant

que des pièces de rechange identiques. Cela permettra de maintenir une utilisation

sécuritaire de l’outil électrique.

Mesures de sécurité additionnelles

• Tenir l’outil par les surfaces isolées prévues à cet effet pendant toute utilisation où

l’organe de coupe pourrait entrer en contact avec des fils électriques cachés ou son

propre cordon. Tout contact de l’organe de coupe avec un fil sous tension mettra

les parties métalliques exposées de l’outil électrique sous tension et électrocutera

l’utilisateur.

• Utiliser des brides de fixation ou un autre dispositif de fixation permettant de soutenir

et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main ou contre son

corps la rend instable et risque de provoquer une perte de maîtrise de l’outil.

• Tenir les mains éloignées des pièces mobiles. Ne jamais placer les mains à proximité de

la zone de découpe.

• Tenir les mains éloignées de la zone de découpe. En cours de découpe, ne jamais passer

les mains sous ou derrière le matériau qui est découpé pour quelque raison que ce soit.

• Ne jamais tenir la pièce dans les mains, sur les genoux ou contre toute partie du

corps en cours de découpe. La scie pourrait glisser et la lame pourrait atteindre le corps et

provoquer des blessures.

• Tre très prudent pour effectuer une coupe au-dessus de la tête et porter une

attention accrue aux fils en hauteur pouvant être cachés. Prévoir la direction de la chute

des branches et de débris.

• Ne pas faire fonctionner cet outil durant de longues périodes. Les vibrations causées

par le fonctionnement de cet outil peuvent provoquer des blessures permanentes aux doigts,

aux mains et aux bras. Utiliser des gants pour amortir davantage les vibrations, prendre de

fréquentes périodes de repos et limiter la durée d’utilisation.

• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles.

Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces

mobiles.

Product specificaties

Merk:	DeWalt
Categorie:	Zaagmachine
Model:	DW311K

Heb je hulp nodig?

Als je hulp nodig hebt met DeWalt DW311K stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine DeWalt

DeWalt DW861 Handleiding

11 September 2024

DeWalt DCS397 Handleiding

15 Juli 2024

DeWalt DCS778 Handleiding

15 Juli 2024

DeWalt DWE249 Handleiding

15 Juli 2024

DeWalt DCMCS574 Handleiding

12 Juni 2024

DeWalt DAH180032 Handleiding

11 Juni 2024

DeWalt DCS378 Handleiding

9 Juni 2024

DeWalt DCS573 Handleiding

3 Juli 2023

DeWalt DCCS623 Handleiding

30 Juni 2023

DeWalt DC310K Handleiding

16 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova E60CS Handleiding

20 December 2024

Silverline 447132 Handleiding

19 December 2024

Silverline 427644 Handleiding

19 December 2024

Herkules KS 210 Profi Handleiding

17 December 2024

Total TS730301 Handleiding

16 December 2024

Total TJSLI8501 Handleiding

16 December 2024

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024

Bavaria BJS 400 Handleiding

5 December 2024

Bavaria BCS 64/1 Handleiding

5 December 2024

Bavaria BEC 2040 TC Handleiding

5 December 2024