DeWalt D28715X Handleiding

DeWalt Zaagmachine D28715X

Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt D28715X (7 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/7
D28715 Heavy-Duty 14" (355 mm) Chop Saw with Quick-Change Clamp
Scie fendeuse robuste D28715, 355 mm (14 po) dotée d’une bride à Attache Rapide
(Quick-Change)
Sierra trozadora con abrazadera de Cambio Rápido (Quick-Change) de 355 mm (14") para
trabajo pesado D28715
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D WALT • www.dewalt.comE
DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
(AUG08) Part No. N014387 D28715 Copyright © 2006, 2008 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black
color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box
configuration; and the array of lozenge-shaped humps on the surface of the tool.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT
TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to these
symbols.
DANGER: Indicates an imminently hazardous situation which,
if not avoided, result in will death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if
not avoided, result in could death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, result in may minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
Important Safety Instructions
WARNING: Read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
• KEEP GUARDS IN PLACE and in working order.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet
locations, or expose them to rain. Keep work area well lighted.
• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work
area.
• MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing
starter keys.
• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was
designed.
• USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not
designed.
• USE PROPER EXTENSION CORD. Make sure your extension cord is in good
condition. When using and extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the correct size to
use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Ampere Rating
Volts Total Length of Cord in Feet (meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
More
Than
Not More
Than
AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
• WEAR PROPER APPAREL. Do not wear loose clothing, neckties, rings, bracelets, or
other jewelry which may get caught in moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair. Air vents often cover moving parts
and should also be avoided.
• ALWAYS USE SAFETY GLASSES which meet the ANSI Z87.1 requirements. Also
use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have
impact resistant lenses, they are not safety glasses.
• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand
and it frees both hands to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
• DISCONNECT TOOLS before servicing; when changing accessories, such as blades,
bits, cutters, and the like.
• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off
position before plugging in.
• USE RECOMMENDED ACCESSORIES. Consult the instruction manual for
recommended accessories. The use of improper accessories may cause risk of injury
to persons.
• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that
is damaged should be carefully checked to determine that it will operate properly
and perform its intended function — check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged should be properly repaired or
replaced.
• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave
tool until it comes to a complete stop.
• REPLACEMENT PARTS. When servicing use only identical replacement parts.
• TO REDUCE THE RISK OF ELECTRIC SHOCK:
a. This equipment may have a polarized plug (one blade is wider than the other.)
This plug will fit in a polarized outlet only one way. If the plug does not fit, contact a
qualified electrician to install the proper outlet.
b. The tool may be equipped with a 3-prong grounding type plug. This plug is to be
used in a grounded outlet only. If the plug does not fit, contact a qualified electrician
to install the proper outlet.
c. Do not alter the plug in any way.
Additional Safety Rules for Chop Saw
• Always wear proper eye and respiratory protection.
• Before using, inspect the cutting wheel for cracks or flaws. If such a crack or flaw
is evident, discard the wheel. The wheel should also be inspected whenever you
think the tool may have been dropped. Flaws may cause wheel breakage.
• When starting the tool with a new or replacement wheel or if you are unsure of
the condition of the wheel, hold the tool in a well protected area and let it run for
one minute. If the wheel has an undetected crack or flaw, it should burst in less than
one minute. Never start the tool with a person in line with the wheel. This includes the
operator.
• In operation, avoid bouncing the wheel or giving it rough treatment. If this occurs,
stop the tool and inspect the wheel for cracks or flaws.
• NEVER have any part of your body in line with the path of the saw blade. Personal
injury will occur.
• Clean your chop saw periodically following the procedure in this manual.
• Do not remove wheel guards or base.
• ALWAYS USE THE VISE OR SPECIAL FIXTURE TO CLAMP WORK SECURELY.
Other aids such as spring, bar, or C-clamps may be appropriate for certain sizes and
shapes of workpiece. Use care in selecting and placing these clamps and make a dry
run before making a cut.
• Use only 14" type 1 wheels rated at 4100 rpm or higher.
• Allow cut off parts to cool before handling.
• Do not attempt to cut wood or plastic with this tool.
• NEVER CUT MAGNESIUM WITH THIS TOOL.
• Use chop saw in a well-ventilated area.
• Turn chop saw off before removing any pieces from the base.
• DO NOT CUT ELECTRICALLY LIVE MATERIAL.
• Do not use circular saw blades or any other toothed blades with this tool. Serious
injury may result.
• DO NOT OPERATE THIS TOOL NEAR FLAMMABLE LIQUIDS, GASES OR DUST.
Sparks or hot chips from cutting or arcing motor brushes may ignite combustible
materials.
• Do not use the side of the abrasive wheel as a deburring grinder. This will substantially
weaken the wheel creating an unsafe condition. The wheel may come apart.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed
to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face
and body.
WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS wear certified
safety equipment:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI S12.6 (S3.19) hearing protection
• NIOSH/OSHA/MSHA respiratory protection.
CAUTION: Wear appropriate hearing protection during use. Under some conditions
and duration of use, noise from this product may contribute to hearing loss.
CAUTION: Spark deflector will get hot. Avoid touching or adjusting while hot. Keep
cordset and materials away from spark deflector.
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V .................. volts A .................. amperes
Hz ................ hertz W ................. watts
min .............. minutes ................. alternating current
................ direct current no ................ no load speed
................. Class I Construction ................. earthing terminal
.................... (grounded) ................. safety alert symbol
................. Class II Construction .../min ...........revolutions or reciprocation
.................... (double insulated) .....................per minute
BPM ............ beats per minute
For your convenience and safety, the following warnings are on your Heavy-Duty 14"
(355 mm) Chop Saw:
FOR SAFE OPERATION READ THE INSTRUCTION MANUAL.
DO NOT USE TOOTHED BLADES.
USE ONLY REINFORCED WHEELS RATED 4100 RPM OR HIGHER.
WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
ALWAYS: WEAR EYE PROTECTION, USE GUARDS, CLAMP WORK IN VISE,
USE PROPER RESPIRATORY PROTECTION.
DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.
Features (Fig. 1, 7)
A. Lock pin J. Wheel
B. Spark deflector screw K. Spark guard
C. Spark deflector L. Wheel lock lever
D. Base M. Trigger switch
E. Fence N. Padlock hole
F. Vise O. Extra blade bolt
G. 8mm Allen wrench P. Extra blade bolt washer
H. Crank Q. Quick-Change blade clamp
I. Vise lever
Power Supply
Be sure your power supply agrees with the nameplate marking. 120 volts, “60 Hz” means
alternating current (normal 120 volt, 60 Hz house current).
A voltage decrease of more than 10% will cause a loss of power and overheating.
Cutting Capacity
The wide vise opening and high pivot point provide cutting capacity for many large pieces.
Use the cutting capacity chart to determine total maximum size of cuts that can be made
with a new wheel.
CAUTION: CERTAIN LARGE, CIRCULAR OR IRREGULARLY SHAPED OBJECTS
MAY REQUIRE ADDITIONAL HOLDING MEANS IF THEY CANNOT BE HELD
SECURELY IN VISE.
CAUTION: DO NOT CUT MAGNESIUM WITH THIS TOOL. Damage to the saw and
personal injury may result.
MAXIMUM CUTTING CAPACITY
NOTE: Capacity shown on chart assumes no wheel wear and optimum fence position.
Standard Equipment
1 14" (355 mm) metal cutting abrasive wheel
1 Allen wrench
1 Instruction manual
To Carry (Fig. 1)
Fold down unit to position where you can carry the saw. Push in lock pin (A) to lock arm
down.
Unlocking (Fig. 1)
To unlock tool and raise head, depress motor arm slightly and pull lock pin (A) out. Motor
arm will then pivot upward.
Material Clamping and Supporting
• Angles are best clamped and cut with both legs resting against base.
• A spacer block slightly narrower than the workpiece can be used to increase wheel
utilization (Fig. 3).
• Long workpieces must be supported by a block so it will be level with top of base
(Fig. 4). The cut-off end should be free to fall downward to avoid wheel binding.
Spark Defl ector Adjustment (Fig. 1)
To best deflect sparks away from surrounding persons and materials, loosen the screw
(B), adjust the spark deflector (C) and then retighten screw.
CAUTION: Risk of property damage. Do not allow cordset to come into contact with
deflector or sparks as damage to cordset may occur.
Vise Operation (Fig. 5)
The vise has a quick travel feature. To release the vise (F) when it is clamped tightly, turn
the crank (H) counterclockwise one or two times to remove clamping pressure. Lift the vise
lever (I) up. Pull crank assembly out as far as desired. The vise may be shoved into work
without cranking. Lower vise lever then tighten vise on work by using crank.
Fence Operation (Fig. 5)
WARNING: To reduce the risk of injury, turn unit off and disconnect machine
from power source before installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
The fence (E) requires no tools to adjust. The quick-release clamp lever (T) unlocks and
locks the fence. When the lever is rotated fully forward, the fence is unlocked. The fence
can then be freely moved forward, backward or rotated to allow for the best cutting position
for a new wheel and as the wheel wears.
Rotating the lever fully to the rear locks the fence in position selected. If the bottom leg
of the lever is not horizontal (parallel to the base), the fence is not locked. Lever will only
lock fence when there is strong resistance to moving it to rear. If resistance is light, adjust
clamping force by tightening slightly the two bolts (R) holding the fence to the base. Test
by reclamping and attempt to move fence.
Fence Angle Adjustment (Fig. 6)
WARNING: To reduce the risk of injury, turn unit off and disconnect machine
from power source before installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
The angle adjustment indicator is part of fence clamping system. Align the desired angle
indicator line with the edge of the slot in base.
FOR A MORE ACCURATE SQUARE CUT
1. Unlock the fence.
2. Push the arm down until the wheel extends into the base.
3. Place a square against the wheel and adjust the fence against the square.
4. Lock the fence into position.
Usage (Fig. 1, 2)
Refer to Figure 2 for proper body positioning during use.
To start the tool, depress the trigger switch (M). To turn the tool off, release the trigger
switch. Keep hands and material from wheel until it has coasted to a stop.
To prevent unauthorized use of tool, install a standard padlock (not included) into the
padlock hole (N) located in the trigger.
Removal and Installation of Wheels (Fig. 7)
WARNING: To reduce the risk of injury, turn unit off and disconnect machine
from power source before installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
The Quick-Change blade clamp requires no tools to change the blade.
1. Push in wheel lock lever (L) and rotate wheel (J) by hand until wheel lock lever
engages slot in inside flange (S) to lock wheel. Loosen the Quick-Change blade clamp
(Q) counterclockwise. Clamp has right-hand thread.
2. Remove the Quick-Change blade clamp (Q), blade clamp washer (U) and old wheel
(J) by hand.
FIG. 1
L
K
I
J
G
F
E
D
C
B
A
N
M
H
FIG. 5
T H
FORWARD
MARCHE AVANT
REENVIAR
E
I
F
R
10-1/8”
(257 MM)
17-3/8”
(441 MM)
FIG. 8
BLOCK
BLOC
EXTREMO
CORTANTE
CUT OFF
END
EXTRÉMITÉ
COUPÉE
DEL
BLOQUE
FIG. 4
ANGLE ADJUSTMENT INDICATOR
INDICATEUR DE RÉGLAGE DE L’ANGLE
INDICADOR DE AJUSTE DE ÁNGULO
SLOT EDGE
BORD DE
LA FENTE
BORDE DE
LA RANURA
WHEEL / MEULE
DISCO
SQUARE / ÉQUERRE
REGLA
FIG. 6
FIG. 3
WIDTH OF SPACER BLOCK
LARGEUR DE LA CALE
D’ECARTEMENT
PROFUNDIDAD DEL BLOQUE
ESPACIADOR
DIAMETER OF WORK PIECE
DIAMETRE DE LA PIECE
DE TRAVAIL
DIÁMETRO DE LA
PIEZA DE TRABAJO
F
SPACER BLOCK
CALE
D’ECARTEMENT
BLOQUE
ESPACIADOR
E
Y.3"
(8MM)
FIG. 10
Y
X
V
W
NA IL
CLOU
CLAVO
FIG. 9
20"
(508MM)
2" (50.8MM)
4"
(101.6MM)
FIG. 2
FIG. 7
Q
U
J
S
O
U
P
J
S
3. Make sure flange surfaces are clean and flat. Install the new abrasive wheel by
reversing the above steps.
4. Tighten the Quick-Change blade clamp clockwise until the knob clicks as least
three times to ensure the knob is tight. The Quick-Change blade clamp cannot be
overtightened.
NOTE: A keyed blade clamp system which includes a blade bolt and blade bolt washer,
(Fig. 7 O, P) is available at extra cost from your local dealer or authorized service center.
Please call 1-800-4-DEWALT (1-800-433-9258) for more information. When using the
keyed blade clamp system, do not overtighten bolt.
WARNING: Risk of personal injury. Check the work surface that the chop saw rests
on when replacing with a new abrasive wheel. It is possible that the wheel may contact
ANY ITEMS OR STRUCTURE THAT EXTENDS ABOVE work surface (under the base)
when the arm is fully lowered.
Mounting (Fig. 8, 9)
CAUTION: Tool must be supported on stable, level, non-skid surface to prevent
unexpected movement when operating.
PROCEDURE FOR PERMANENT MOUNTING
1. Drill four holes 5/16" (8 mm) through the work surface (Fig. 8).
2. Insert 1/4-20 screws down through the holes in the base and through holes in
mounting surface. The approximate length of the screws should be the thickness of the
mounting surface plus 4" (102 mm).
CRADLE MOUNTING
1. Cut two boards approximately 20" long x 2" high x 4" wide (508 x 50.8 x mm).101.6
2. Place chop saw at desired work location.
3. Place boards tightly along side, and nail to work surface (Fig. 9).
Operation Tips for More Accurate Cuts
• Allow the wheel to do the cutting. Excessive force will cause the wheel to glaze
reducing cutting efficiency and/or to deflect causing inaccurate cuts.
• Properly adjust fence angle.
• Make sure material is laying flat across base.
• Properly clamp material to avoid movement and vibration.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect machine
from power source before installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
MOTOR BRUSH INSPECTION AND REPLACEMENT (FIG. 10)
Brushes should be regularly inspected for wear. To inspect brushes, unscrew the two
end cap screws (W) and remove end cap (V). Remove brush cap (X). Brushes (Y) should
slide freely in brush box. If brushes are worn down to .3" (8 mm) as shown in Figure 10
they should be replaced. To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed. Replace the brush cap (do
not overtighten). Replace end cap and two screws. Tighten securely.
Cleaning
WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt
is seen collecting in and around the air vents. Wear ANSI Z87.1 (CAN/CSA Z94.3)
approved eye protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the plastic materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments
(including brush inspection and replacement) should be performed by a D EWALT factory
service center, a DEWALT authorized service center or other qualified service personnel.
Always use identical replacement parts.
NOTE: Unit may be converted to a three-wire twist lock cord set at an authorized service
center.
Lubrication
Closed-type, grease-sealed ball bearings are used throughout. These bearings have
sufficient lubrication packed in them at the factory to last the life of the chop saw.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been
tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only DEWALT, recommended accessories should be used with
this product.
Use only high-strength Type 1 organic bonded wheels rated 4100 rpm or higher.
Recommended accessories for use with your tool are available at extra cost from your
local dealer or authorized service center. If you need assistance in locating any accessory
for your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore,
MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship
for three years from the date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of warranty coverage and warranty
repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This
warranty does not apply to accessories or damage caused where repairs have been made
or attempted by others. This warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D EWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any
time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D EWALT Power Tool,
Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained either
in the packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.
SI VOUS AVEZ DES QUESTIONS OU VOULEZ NOUS FAIRE PART DE VOS
COMMENTAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL DEWALT,
COMPOSEZ SANS FRAIS LE : 1 800 433-9258.
Défi nitions : lignes directrices en
matière de sécurité
Les définitions ci-dessous décrivent le niveau de danger pour chaque
mot-indicateur employé. Veuillez lire le mode d’emploi et porter une atten-
tion particulière à ces symboles.
DANGER : indique une situation dangereuse imminente qui, si elle n’est
pas évitée, causera la mort ou des blessures graves.
AVERTISSEMENT : indique une situation potentiellement dangereuse
qui, si elle n’est pas évitée, se solder par unpourrait décès ou des
blessures graves.
MISE EN GARDE : indique une situation potentiellement dangereuse
qui, si elle n’est pas évitée se solder par pourrait des blessures mineures
ou modérées.
MISE EN GARDE : utilisé sans le symbole d’alerte à la sécurité, indique
une situation potentiellement dangereuse qui, si elle n’est pas évitée
pourrait se solder par des dommages à la propriété.
Consignes de sécurité importantes
AVERTISSEMENT : lire et comprendre toutes les directives. Le non-respect des
directives indiquées ci-dessous peut entraîner des risques de choc électrique, d’incendie
ou de blessures graves.
CONSERVER CES DIRECTIVES
• MAINTENIR LES DISPOSITIFS DE PROTECTION EN PLACE et en bon état de
fonctionnement.
• RETIRER LES CLES A MOLETTE ET LES CLES DE REGLAGE. S’habituer à vérifier
que les clés et les clés de réglage ont été retirées de l’outil avant de le mettre en
marche.
• GARDER LA ZONE DE TRAVAIL PROPRE. Les zones et établis encombrés sont
souvent des causes de blessures.
• NE PAS UTILISER CET OUTIL DANS UN ENVIRONNEMENT DANGEREUX. Ne pas
utiliser d’outils électriques dans des endroits humides ou mouillés et ne pas les exposer
à la pluie. Garder la zone de travail bien éclairée.
• TENIR LES ENFANTS A L’ECART. Tous les visiteurs doivent se trouver à une distance
sûre de la zone de travail.
• S’ASSURER QUE L’ATELIER NE PRESENTE PAS DE DANGER POUR LES
ENFANTS en utilisant des cadenas, des interrupteurs principaux ou en retirant les clés
de démarrage.
• NE PAS FORCER L’OUTIL. Le travail sera mieux accompli et plus sécuritaire au
rythme prévu pour l’appareil.
• UTILISER L’OUTIL APPROPRIE. Ne pas forcer un outil ou un accessoire pour
effectuer un travail auquel il n’a pas été conçu.
• UTILISER LA RALLONGE APPROPRIEE. S’assurer que la rallonge est en bon état.
Lorsque qu’une rallonge électrique est utilisée, s’assurer d’en utiliser une de calibre
suffisamment élevé pour assurer le transport du courant nécessaire au fonctionnement
de l’appareil. Un cordon de calibre inférieur causera une chute de tension de ligne et
donc une perte de puissance et une surchauffe. Le tableau suivant indique le calibre
approprié à utiliser selon la longueur du cordon et l’intensité nominale de la plaque
signalétique. En cas de doute, utiliser le calibre suivant le plus gros. Plus le numéro de
calibre est petit, plus le cordon est lourd.
Calibres minimaux des rallonges
Intensité
(en ampères)
Volts Longueur totale de cordon en mètres (pieds)
120V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)
240V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)
Supérieur
à
Inférieur
à AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Non recommandé
• PORTER LES VETEMENTS APPROPRIES. Ne porter ni vêtements amples, ni
gants, ni cravates, ni bagues, ni bracelets, ni autre bijoux, car ces derniers pourraient
s’enchevêtrer dans des pièces mobiles. Le port de chaussures antidérapantes est
recommandé. Se couvrir les cheveux s’ils sont longs. Se tenir éloigné des évents
puisque ces derniers recouvrent souvent des pièces en mouvement.
• TOUJOURS PORTER DES LUNETTES DE SECURITE conforme aux exigences de la
norme ANSI Z87.1. Utiliser également un masque facial ou anti-poussière si l’opération
de découpe génère de la poussière. Les lunettes courantes comportent seulement des
lentilles résistantes aux chocs, ce ne sont pas des lunettes de sécurité.
• FIXER LA PIECE. Utiliser des brides ou un étau pour retenir la pièce. C’est plus
sécuritaire que d’utiliser votre main et cela vous permet d’utiliser les deux mains pour
faire fonctionner l’outil.
• NE PAS TROP TENDRE LES BRAS. Conserver son équilibre en tout temps.
• PRENDRE SOIN DES OUTILS. S’assurer que vos outils sont aiguisés et propres
afin d’optimiser sécurité et performance. Suivre les consignes de graissage et de
changement d’accessoires.
• DEBRANCHER LES OUTILS avant de les réparer et au moment de changer
d’accessoires, tels que les lames, les mèches, les couteaux, etc.
• REDUIRE LE RISQUE DE DEMARRAGE ACCIDENTEL. S’assurer que l’interrupteur
est en position ARRÊT avant de brancher l’outil.
• UTILISATION DES ACCESSOIRES RECOMMANDES. Une liste des accessoires
recommandés se trouve dans le mode d’emploi. L’utilisation d’accessoires incorrects
peut entraîner un risque de blessure corporelle.
• NE JAMAIS SE TENIR SUR L’OUTIL. Une blessure grave pourrait se produire en cas
de basculement de l’outil ou de démarrage accidentel de l’outil de découpe.
• VERIFIER LES PIECES ENDOMMAGEES. Avant toute utilisation ultérieure de l’outil,
un protège-lame (ou une autre pièce) endommagé doit être soigneusement examiné
afin de déterminer s’il fonctionnera correctement et remplira sa fonction prévue –
vérifier l’alignement des pièces mobiles, la présence de grippage des pièces mobiles,
de rupture de pièces, la fixation et tout problème pouvant nuire au fonctionnement de
l’outil. Un protège-lame (ou tout autre pièce) endommagé doit être réparé et remplacé
adéquatement.
• NE JAMAIS LAISSER L’OUTIL FONCTIONNER SANS SURVEILLANCE. ETEINDRE
L’APPAREIL. Ne pas laisser l’outil tant qu’il n’est pas complètement arrêté.
• PIECES DE RECHANGE IDENTIQUES. Pour la réparation, utiliser uniquement des
pièces de rechange identiques.
• POUR REDUIRE LE RISQUE DE CHOCS ELECTRIQUES :
a. Cet équipement peut être pourvu d’une fiche polarisée (une broche est plus large
que l’autre.) Cette fiche pourra être insérée dans une prise polarisée, dans un
sens seulement. Si elle ne s’insère pas dans la prise, demander à un électricien
compétent d’installer une fiche polarisée.
b. L’outil peut comprendre une fiche de mise à la terre à trois broches. Cette fiche ne
doit être insérée que dans une prise mise à la terre. Si elle ne s’insère pas dans la
prise, demander à un électricien compétent d’installer une fiche polarisée.
c. Ne modifier la fiche en aucune façon.
Autres règles de sécurité pour la scie fendeuse
• Toujours porter une protection oculaire et respiratoire adéquate.
• Avant d’utiliser l’outil, inspecter la meule de coupe à la recherche de fissures ou
de défectuosités. Si une fissure ou une défectuosité est présente, jeter la meule.
La meule doit également être inspectée lorsqu’il est possible que l’outil soit
tombé. Les défectuosités peuvent causer un bris de la meule.
• Au moment de démarrer l’outil avec une meule neuve ou de rechange, ou en cas
d’incertitude quant à l’état de la meule, tenir l’outil dans un endroit bien protégé
et le laisser fonctionner pendant une minute. Si la meule comporte une fissure ou
une fêlure non détectée, l’accessoire devrait éclater en moins d’une minute. Ne jamais
démarrer l’outil lorsque quelqu’un est aligné avec la meule. Cela inclut l’opérateur.
• Durant le fonctionnement de l’outil, éviter de faire rebondir le disque ou de le
traiter rudement. Dans ces cas, arrêter l’outil et inspecter la meule pour toute trace
de fissure ou de fêlures.
• AUCUNE partie du corps ne doit se trouver dans la trajectoire de la lame de la
scie. Il y a risque de blessures corporelles.
• Nettoyer périodiquement la scie fendeuse selon la procédure indiquée dans le présent
manuel.
• Ne pas enlever le protège-meule ni la base.
• TOUJOURS UTILISER L’ETAU OU LE DISPOSITIF DE FIXATION SPECIAL POUR
BIEN SERRER LA PIECE. D’autres accessoires tels que des pinces à ressort, des
serres à barre ou du serre-joint en C peuvent convenir à certaines tailles et formes de
pièces. Choisir et placer judicieusement ces accessoires, puis faire fonctionner l’outil à
sec avant de réaliser une coupe.
• Utiliser uniquement des meules de 533 mm (14 po) type 1 dont la vitesse atteint au
moins 4100 tr/min.
• Laisser les pièces coupées refroidir avant de les manipuler.
• Ne pas tenter de couper du bois ou du plastique avec cet outil.
• NE JAMAIS COUPER DU MAGNESIUM AVEC CET OUTIL.
• Utiliser la scie fendeuse dans un endroit bien ventilé.
• Éteindre la scie fendeuse avant d’enlever tout morceau de la base.
• NE PAS COUPER DE MATERIAU SOUS TENSION.
• Ne jamais utiliser de lames de scie circulaire ou toutes autres lames dentées
avec l’outil. Elles pourraient provoquer de graves blessures.
• NE PAS FAIRE FONCTIONNER CET OUTIL PRES DE LIQUIDES INFLAMMABLES,
DE GAZ OU DE POUSSIERE. Les étincelles ou copeaux chauds, qui proviennent
de la coupe ou des balais du moteur émettant des décharges électriques, peuvent
enflammer du matériel combustible.
• Ne pas utiliser le côté de la meule abrasive comme machine à ébavurer. Cela risque de
fragiliser considérablement la meule et de créer une condition dangereuse. La meule
risque de se séparer.
AVERTISSEMENT : certaines poussières produites par les activités de ponçage, de
sciage, de meulage, de perçage ainsi que d’autres activités de construction peuvent
contenir des produits chimiques pouvant causer le cancer, des anomalies congénitales
ou d’autres problèmes liés aux fonctions reproductrices. Voici quelques exemples de ces
produits chimiques :
• le plomb contenu dans les peintures à base de plomb,
• la silice cristalline de la brique, du ciment et d’autres produits de maçonnerie, et
• l’arsenic et chrome provenant de bois traité chimiquement.

Product specificaties

Merk: DeWalt
Categorie: Zaagmachine
Model: D28715X

Heb je hulp nodig?

Als je hulp nodig hebt met DeWalt D28715X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine DeWalt

DeWalt

DeWalt DW861 Handleiding

11 September 2024
DeWalt

DeWalt DCS397 Handleiding

15 Juli 2024
DeWalt

DeWalt DCS778 Handleiding

15 Juli 2024
DeWalt

DeWalt DWE249 Handleiding

15 Juli 2024
DeWalt

DeWalt DCMCS574 Handleiding

12 Juni 2024
DeWalt

DeWalt DAH180032 Handleiding

11 Juni 2024
DeWalt

DeWalt DCS378 Handleiding

9 Juni 2024
DeWalt

DeWalt DCS573 Handleiding

3 Juli 2023
DeWalt

DeWalt DCCS623 Handleiding

30 Juni 2023
DeWalt

DeWalt DC310K Handleiding

16 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Shindaiwa

Shindaiwa 269TS Handleiding

19 November 2024
Shindaiwa

Shindaiwa 320TS Handleiding

19 November 2024
Shindaiwa

Shindaiwa 488 Handleiding

19 November 2024
Shindaiwa

Shindaiwa 352s Handleiding

19 November 2024
Ergotools Pattfield

Ergotools Pattfield E-PST 800 L Handleiding

19 November 2024
Bavaria By Einhell

Bavaria By Einhell Bavaria BFS 600 E Handleiding

19 November 2024
Bavaria By Einhell

Bavaria By Einhell Bavaria BSTL 800 Profi Handleiding

19 November 2024
Proviel

Proviel STL 800 Handleiding

19 November 2024
Proviel

Proviel PVBK 40 Handleiding

19 November 2024
Proviel

Proviel PVKS 38/40 B Handleiding

19 November 2024