Delonghi DCH7093ER Handleiding

Delonghi Heater DCH7093ER

Lees hieronder de 📖 handleiding in het Nederlandse voor Delonghi DCH7093ER (3 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 68 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

INTRODUCTION

Thank you for choosing a De’Longhi product.

Please take a few minutes to read these instructions.

This will avoid all risks and damage to the appliance.

IMPORTANT SAFEGUARDS

- Do not use the appliance near showers, bathtubs, sinks,

swimming pools, etc.

- Always use the appliance in an upright position.

- Do not use the appliance to dry laundry. Do not obstruct

the air intake and outlet grilles (danger of overhea-

ting).

- The appliance is not intended for use by persons (inclu-

ding children) with reduced physical, sensory or men-

tal capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

- The heater must be positioned at least 50 cm from furni-

ture or other objects.

- Do not use the appliance near walls, furniture, curtains,

etc.

- The use of extension leads is not recommended.

However if they cannot be avoided, follow the instruc-

tions accompanying the extension lead and never exce-

ed the power limit marked on the extension.

- If the power cable is damaged, it must be replaced by

the manufacturer, an authorised service centre or a qua-

lied electrician in order to eliminate all risk.

- The appliance must not be placed immediately under a

xed power socket.

- Do not use the appliance in rooms with a oor area of

less than 4m2.

- Before putting the appliance away, make sure it is com-

pletely o and unplugged from the mains socket. Wrap

the cable around the base. Do not store in dusty atmos-

pheres.

- Room temperature should be between 0 and 30° C.

- Do not rest anything on the appliance.

- To avoid the safety system resetting accidentally, this

appliance must not be powered through an external on/

o device such as a timer, or connected to a circuit which

is turned o and on regularly by the energy supplier.

IMPORTANT: To avoid overheating, never under

any circumstances cover the appliance during

operation as this would lead to a dangerous rise in

temperature.

Safety functions

- the appliance is tted with a safety Safety device:

device which switches it o in the event of accidental

overheating (e.g. obstruction of air intake and outlet

grilles, motor turning slowly or not at all).

To reset, unplug the appliance from the mains socket for

a few minutes, remove the cause of overheating then

plug in again.

- a tip over safety device turns Tip over safety device:

the appliance o if it falls over or is positioned inappro-

priately in such a way as to jeopardise safety.

The appliance emits a beep and a dot ashes on the di-

splay. The appliance resumes operation a few seconds

after being placed in an upright position again.

Disposing of the appliance

In compliance with European directive 2002/96/EC,

the appliance must not be disposed of with house-

hold waste, but taken to an authorised waste separa-

tion and recycling centre.

Important safeguards en

Description/Use en

DESCRIPTION

(see g. 1)

A ON/STAND-BY button

B +/- adjustment buttons

C MODE button (selects the operating mode)

D “ECO plus” button

E Timer button

F Swing button

G Remote control receiver

H Indicator light

I Air intake grille

J Filter

USE

Installation

- The appliance can be used on any horizontal surface.

Do not overload the electrical circuit. Avoid using the

same socket for other appliances.

Electrical connection

Before plugging the appliance into the mains socket, check

that the mains power supply corresponds to the value indi-

cated on the rating plate and that the mains power supply

is adequate for the load.

- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/EEC

ON RADIO INTERFERENCE SUPPRESSION.

Operation and use

1. Plug into the mains socket.

2. The appliance emits a beep. The indicator light ( ) co-H

mes on and remains lit while the appliance is powered.

3. The appliance switches to stand-by. A dot ashing on

the display means the tip over device has been activa-

ted. See paragraph: “Safety functions”.

4. Press the ON/STAND-BY ( ) to turn the appliance on. A

It begins heating the room according to the current set-

tings.

5. Press the MODE button ( ) to select one of the following C

operating modes:

Fan

Freeze prevention

Heating 1

Heating 2

Heating 3

5.1 Fan

In this mode, only the fan operates and the appliance does

not heat the room.

5.2 Freeze prevention

In this mode, the appliance keeps the room at a temperature

of 7°C to avoid freezing.

5.3 Heating 1, 2 and Heating 3

In this mode, the desired temperature can be selected by

pressing the adjustment buttons + and – ( ): B

- Heating 1 (low power)

The appliance operates at low power, reducing noise

levels and energy consumption to a minimum.

- Heating 2 (medium power)

The appliance operates at medium power.

- Heating 3 (high power)

The appliance operates at high power to heat the room

rapidly.

6. ECO plus” function“

The ECO plus” function is available in Heating 1, 2 and 3 “

modes only.

To activate the function, press the ECO plus” button ( ). “ D

When this function is active the appliance automatically sets

the most appropriate power level to guarantee optimum

comfort while reducing energy consumption.

While the ECO plus” function is active, the appliance may “

switch automatically to a lower heating power than the one

displayed. This may happen a number of times in an hour.

7. To distribute the air ow over a wider surface, press the

swing button ( ) . The appliance starts swinging to F

the right and left. To stop the appliance in the desired

position, simply press the swing button ( ) again.F

8. To turn the appliance o, press the ON/STAND-BY button

( ). The display may visualize a countdown for about 6 A

seconds.

Please note: Room temperature can be displayed in either

°C or °F. To change the unit of measurement for the tempera-

ture, press the + button for a few seconds, then release.

Digital 24 h timer

This function can be activated from any operating mode.

Auto-start: with the appliance in STAND-BY, press the timer

button (E) . The symbol is displayed together with

the time remaining before the appliance comes on. To adjust

the timer, use the adjustment buttons + and - ( ), then wait B

a few seconds for the setting to be memorised. The stand-by

light ( ) is displayed together with the symbol, indicating H

that the timer has been set. When the programmed time

is reached, the appliance comes on with the settings used

during the previous period of operation.

Auto-o: with the appliance on, press the timer button

( ). The symbol is displayed together with the time remai-E

ning before the appliance goes o.

To set the timer, use the adjustment buttons + and - ( ), then B

wait a few seconds for the setting to be memorised.

The current settings are displayed again, together with the

symbol indicating that the timer has been set.

When the programmed time is reached, the appliance goes o

automatically. To go back to operation without the timer, press

the timer button ( ) twice. E

The timer symbol

disappears from the display.

Using the remote control

The functions on the remote control are the same as those on

the appliance control panel.

For a description of the functions, see the “Operation and use”

section on the previous page.

Inserting or replacing the batteries

The remote control is powered by a

CR2032 lithium battery.

To operate the remote control, pull

and remove the plastic strip under

the battery cover.

To replace the batteries, remove

the battery cover by sliding it as

shown in the gure.

When replacing the batteries,

make sure you respect the polarity

(see gure 2).

Replace the cover as shown in the gure.

Old batteries are harmful to the environment and must be

removed and disposed of in compliance with current legi-

slation.

MAINTENANCE

- Always unplug from the mains socket before cleaning.

- During the season when the appliance is in use, clean

the air intake and outlet grilles regularly using a vacuum

cleaner.

- To clean the lter, remove the rear grille by pulling it

outwards (g. 1). Remove the dust lter which retains

impurities in the air drawn in from the room, blow on it

lightly then replace in the appliance.

- Never use abrasive powders or solvents to clean the ap-

pliance.

TROUBLESHOOTING

If the appliance displays “ ” and emits a beep, the tempera-PF

ture sensor is malfunctioning.

If the problem continues, contact customer services.

If the appliance goes o unexpectedly:

- Make sure it is plugged in correctly to the mains socket.

- Make sure the appliance is standing upright on a at

surface, otherwise the tip over device may be activated.

- Check the temperature and timer settings.

The appliance may have gone o because the set tem-

perature has been reached or the time set on the timer

has elapsed.

TECHNICAL CHARACTERISTICS

Power supply See rating plate

Absorbed power “

Use

Fig. 2

Product specificaties

Merk:	Delonghi
Categorie:	Heater
Model:	DCH7093ER
Soort bediening:	Sensor
Kleur van het product:	Black, White
Aantal vermogenniveau's:	3
Warmtebron:	Electrisch
Soort:	Ventilator elektrisch verwarmingstoestel
LED-indicatoren:	Ja
Aan/uitschakelaar:	Ja
Indicatielampje:	Ja
Power LED:	Ja
AC-ingangsspanning:	220 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Verwarmingsvermogen:	2400 W
Verwarmingselement type:	Keramisch
Verwarming power (min):	- W
Zomer-ventilatie:	Ja
Anti-stof filter:	Ja