Delonghi DCH 6031.B Handleiding

Delonghi Heater DCH 6031.B

Lees hieronder de 📖 handleiding in het Nederlandse voor Delonghi DCH 6031.B (3 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

DESCRIPTION

(see g. 1)

A ON/STAND-BY button

B +/- adjustment buttons

C MODE button (selects the operating mode)

D “ECO plus” button

E Timer button

F Swing button

G Remote control receiver

H Remote control

I Indicator light

J Air intake grille

K Filter

USE

Installation

The appliance can be used on any horizontal surface.

Do not overload the electrical circuit. Avoid using the same

socket for other appliances.

Electrical connection

- Before plugging the appliance into the mains socket,

check that the mains power supply corresponds to the

value indicated on the rating plate and that the mains

power supply is adequate for the load.

- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/

EEC ON RADIO INTERFERENCE SUPPRESSION.

Operation and use

- Plug into the mains socket.

- The appliance emits a beep. The indicator light ( ) comes I

on and remains lit while the appliance is powered.

- The appliance switches to stand-by. A dot ashing

on the display means the tip over device has been

activated. See paragraph: “Safety functions”.

- Press the ON/STAND-BY ( ) to turn the appliance on. A

It begins heating the room according to the current

settings.

- Press the MODE button (C) to select one of the following

operating modes:

- Fan

In this mode, only the fan operates and the appliance

does not heat the room.

- Freeze prevention

In this mode, the appliance keeps the room at a

temperature of 7°C to avoid freezing.

- Heating

In this mode, the desired temperature can be selected

by pressing the adjustment buttons + and – ( ): B

- Heating

Silent+

The appliance operates at minimum power, automati-

cally reducing energy consumption and noise level. The

tones emitted by the commands are lower than in other

modes for even more silent operation.

- Heating

The appliance operates at medium power.

- Heating

The appliance operates at high power to heat the room

rapidly.

- To turn the appliance o, press the ON/STAND-BY

button ( ). The display may visualize a countdown for A

about 6 seconds.

Please note: Room temperature can be displayed in

either °C or °F. To change the unit of measurement for the

temperature, press the + button for a few seconds, then

release.

“ECO plus” function

The “ECO plus” function is available in Heating 1, 2 and 3 modes

only. To activate the function, press the ECO plus” button (“ D).

When this function is active the appliance automatically sets

the most appropriate power level to guarantee optimum

comfort while reducing energy consumption.

While the ECO plus” function is active, the appliance may “

switch automatically to a lower heating power than the one

displayed. This may happen a number of times in an hour.

Swing button

To distribute the air ow over a wider surface, press the swing

button ( . The appliance starts swinging to the right F)

and left. To stop the appliance in the desired position, simply

press the swing button ( ) again.F

Digital 24 h timer

This function can be activated from any operating mode.

Auto-start: with the appliance in STAND-BY, press the timer

button (E). The symbol is displayed together with

the time remaining before the appliance comes on.

To adjust the timer, use the adjustment buttons + and - (B),

then wait a few seconds for the setting to be memorised. The

stand-by light ( ) is displayed together with the symbol, I

indicating that the timer has been set.

When the programmed time is reached, the appliance comes

on with the settings used during the previous period of

operation.

Auto-o: with the appliance on, press the timer button

( symbol is displayed together with the time E). The

remaining before the appliance goes o.

To set the timer, use the adjustment buttons + and - (B),

then wait a few seconds for the setting to be memorised.

The current settings are displayed again, together with the

symbol indicating that the timer has been set.

When the programmed time is reached, the appliance goes

o automatically. To go back to operation without the timer,

press the timer button ( ) twice. E

The timer symbol disappears from the display.

USING THE REMOTE CONTROL

The functions on the remote control are the same as those on

the appliance control panel.

For a description of the functions, see the “Operation and use”

section on the previous page.

Inserting or replacing the batteries

- The remote control is

provided with a lithium

battery CR2032. To let

the appliance function,

remove the battery cover

strip, by pulling it.

- To replace the batteries,

remove the battery cover

by rotating it. Replace the

battery paying attention to

respect the right polarity as shown in gure 1.

- Replace the cover rotating it towards the position .

- Old batteries must be removed and disposed o in

accordance with current legislation as they are harmful

to the environment.

MAINTENANCE

- Always unplug from the mains socket before cleaning.

- During the season when the appliance is in use, clean

the air intake and outlet grilles regularly using a vacuum

cleaner.

- To clean the lter, remove the rear grille by pulling it

outwards.

Remove the dust lter which retains impurities in the air

drawn in from the room, blow on it lightly then replace

in the appliance.

- Never use abrasive powders or solvents to clean the

appliance.

TECHNICAL CHARACTERISTICS

Supply voltage See rating plate

Absorbed power “

Fig. 2

PROBLEM CAUSE SOLUTION

PF display and emits a beep Temperature sensor is not working

properly

Please contact Customer Service

Product doesn’t turn on Check that the plug is connected to the

outlet

Auto-start is on

Room temperature reaches the set

temperature

Plug in

Wait till time elapsed or press the but-

ton (E) twice to cancel the auto-start

and push the button (A)

Use the “+” button to increase the set

temperature

The appliance goes o unexpectedly Check that the plug is connected to the

outlet

The set temperature has been reached

or the time set on the timer has elapsed

Plug in

A dot is ashing and unit is o The tip-over switch has been activated Make sure the appliance is standing

upright on a at surface.

If the appli-

ance doesn’t work please contact Cus-

tomer Service

The display shows " " blinkingHtThe internal temperature is too high.

The air intake or outlet grille is

obstructed

Check the appliance is correctly

positioned respecting the minum

distances from the wall, or objects, as

indicated on the instruction manual,

if not, position the appliance correctly

Remove the obstruction

Disconnect the plug from the outlet

and let the appliance cool down. After

few minutes plug the appliance again.

If the appliance doesn't work

please

contact Customer Service

TROUBLESHOOTING

Product specificaties

Merk:	Delonghi
Categorie:	Heater
Model:	DCH 6031.B
Soort bediening:	Draaiknop
Kleur van het product:	Zwart
Aantal vermogenniveau's:	3
Gewicht:	1600 g
Breedte:	227 mm
Diepte:	165 mm
Hoogte:	265 mm
Soort:	Ventilator elektrisch verwarmingstoestel
Ontdooifunctie:	Ja
Vermogen:	2000 W
Indicatielampje:	Ja
Geschikt voor:	Binnen
Instelbare thermostaat:	Ja
Oververhittingsbeveiliging:	Ja
AC-ingangsspanning:	220 - 240 V
AC-ingangsfrequentie:	50/60 Hz
Geschikt voor ruimtevolume tot:	60 m³
Verwarmingsvermogen:	2000 W
Plaatsingsopties:	Vloer
Verwarmingselement type:	Keramisch
Verwarming power (min):	700 W
Zomer-ventilatie:	Ja
Anti-stof filter:	Ja