Datalogic QuickScan Handleiding

Datalogic Barcode lezer QuickScan

Lees hieronder de 📖 handleiding in het Nederlandse voor Datalogic QuickScan (16 pagina's) in de categorie Barcode lezer . Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

Electronic Article Surveillance (EAS)

Installation Instruction Manual

Introduction

The EAS option enables nners toQuickScan QS6000 Plus model sca

provide Electronic Article Surveillance (EAS) deactivation.

This document provides information and procedures to install a new

EAS Antenna Upgrade Kit, or to replace a malfunctioning loop antenna

already installed in the canner. s

The EAS upgrade or replacement of the loop antenna in the scanner

involves:

• Replacing the Scan Window with a new thinner Scan Window

and the EAS Loop Antenna;

• Replacing the Handle Printed Circuit Board (PCB) with one that

contains a connector for the EAS Antenna leads, and

• Replacing the Interface Cable with a special EAS Interface Cable.

The loop antenna connects to the store’s EAS System through this special

Interface Cable

Before installing the upgrade or replacing the EAS antenna, verify that

your EAS Upgrade Kit contains the following items shown in Figure 1.

Scan Window

Loop Antenna

To EAS System

EAS/Interface

Cable

Figure 1. EAS Kit

1. Scan Window/

EAS Antenna.

2. Handle PCB.

3. Insulation Tape Strip

4 . This Instruction Sheet

You should also have the correct

EAS/Interface cable that matches

your POS Terminal connection.

QuickScan® QS6000 Plus

Tools Required

You need the following tools to upgrade or replace the EAS

Antenna:

• Torque Limiting Driver.

• T8 Torx® bit.

• Multimeter (or equivalent) to test for continuity.

• ESD (ElectroStatic Discharge) protection as described below.

• .050 hex driver

ElectroStatic Discharge Protection

To protect static sensitive circuitry, follow these ElectroStatic Discharge

(ESD) procedures when upgrading, or servicing an existing EAS antenna.

Figure 2 shows the ESD materials.

Figure 2. ESD Setup

ESD Procedures:

1. Connect the above ESD components together with a common

ground strap to eliminate any electrical potential.

2. Use the anti-static floor and table mats to neutralize the working

area (floors, carpeting, tables, etc.).

3. Use the anti-static wrist strap to eliminate buildup static charge

picked up from the environment (shoes on carpets, etc.).

4. Attach the anti-static ground clip to a known ground point.

PSC and the PSC logo are registered Trademarks of PSC INC.

QS6000/6000 PLUS

a trademark owned by PSC, Inc. Torx® is a registered trademark of Camcar Textron.

ESD Materials:

1. Anti-static tablemat

2. Anti-static wriststrap

3. Anti-static floormat

4. Earth Ground

Alerts you to use

ESD protection.

Torx® is a registered trademark of Camcar Textron.

Installation/Replacement Procedures

Before you begin

1. Disconnect the Power to the Scanner.

2. Disconnect the scanner from the Point of Sale (POS) Terminal.

3. Place the scanner on its side on the ESD tablemat.

To Replace the EAS antenna or to install a new EAS antenna, use the

procedures described below to:

• Disconnect and replace the Interface Cable (I/F) with a new cable.

• Separate the Left and Right enclosures.

• Remove and Replace the Handle PC Board with a new PC Board.

• Remove and replace the Decoder PC Board.

• Remove the original Scan Window and replace with a new

window and the EAS loop antenna.

Reference the QuickScan lusQS6000 P Service Manual for more

information.

Disconnecting the I/F Cable

The I/F Cable connects the scanner to the POS system and power supply.

1. Insert a .050” hex driver or bent paper clip into the CABLE RELEASE

hole, and press down to unlock the cable connector. Refer to Figure 3.

Interface

Connector

Paper Clip

Ca ble R elea se

Adapter Plug for

QS6000 Plus

I/F Cables

Figure 3. Disconnecting the Interface Cable.

2. Gently pull the cable connector from the scanner.

3. Disconnect the cable from the POS system (connections will vary

depending upon interface type.

This completes I/F Cable disconnection.

Product specificaties

Merk:	Datalogic
Categorie:	Barcode lezer
Model:	QuickScan
Gewicht:	121.9 g
Breedte:	28 mm
Diepte:	26 mm
Hoogte:	67 mm
Soort:	Draagbare streepjescodelezer
Internationale veiligheidscode (IP):	IP42
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Draadloos
Type stroombron:	Batterij/Accu
Meegeleverde kabels:	USB
Waarschuwingssignaal:	Ja
Certificering:	IEC 60825-1
Duurzaamheidscertificaten:	RoHS
Ingangsspanning:	5 V
Aansluitbereik:	12 m
Temperatuur bij opslag:	-40 - 70 °C
Golflengte:	610 nm
Standaard interfaces:	USB
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Batterijtechnologie:	Lithium-Ion (Li-Ion)
Pitch lees-hoek:	-65 - 65 °
2D ( matrix en gestapeld ) barcodes ondersteund:	Niet ondersteund
Yaw lees-hoek:	-65 - 65 °
Tilt lees-hoek:	-45 - 45 °