Cyber Acoustics CA-2050 Handleiding

Cyber Acoustics Speaker CA-2050

Lees hieronder de 📖 handleiding in het Nederlandse voor Cyber Acoustics CA-2050 (24 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/24

CA2050

Maximum Pow e r Out p u t at 14,4V

4Ω 20Hz - 30kHz THD 1% 2x 225W

2Ω 20Hz - 30kHz THD 1% 2x 180W

4Ω 1kHz Mono Bridged 1x 450W

Con t i n u o us Pow er O u t put a t 14,4V

4Ω 20Hz - 30kHz THD 1% 2x 60W

2Ω 20Hz - 30kHz THD 1% 2x 75W

4Ω 1kHz Mono Bridged 1x 180W

Fuse R a t i n g 20A

Dim e n s i o ns 275x220x52mm

E n g l i s h

F E a t u R E s

• Bridgeable outputs.

• ’Tri-mode’ output capability, simultaneous stereo & bridged mono set up is possible.

• Pulse Width Modulated (PWM) MOSFET Power Supply.

• Variable input sensitivity: RCA input 0.5V to 2V.

• Thermal-, Overload- and Shortcircuit protection.

• Excellent muting circuitry assures no turn on/off ‘pops’.

• Built-in High Pass / Full Range / Low Pass Filter Switch. 50Hz - 250Hz

• Chrome plated power connectors for optimal power distribution.

• European design and engineering.

• Chrome plated speaker connectors for optimal signal output.

M O u n t i n g

The amplifier has to have at least 5 cm (2”) ventilation space at all sides, to allow the heat to rise

away from the amplifier. Be sure that the power and signal cables can enter and leave the ampli-

fier in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at

opposite sides of the vehicle to reduce any noises.

The amplifier should be protected from exposure to moisture and direct sunlight.

Mark the mounting surface using the amplifier as a template, then drill 2.5 mm (1/8”) diameter

holes at the marked locations and mount the amplifier using the supplied self-tapping screws.

i n s t a l l a t i O n

Remember to always disconnect battery ground before working on a vehicle’s electrical system!

Always place a fuse or circuit breaker no more than 30 cm (12”) from the battery, no greater

than the fuse(s) of your amplifier for optimal protection.

g E t t i n g y O u R P O w E R s t a R t E D

• First, the +12V terminal is connected directly to the battery of your car. Use a cable of at

least 10 mm2, and make sure that the connectors are of the same value.

- Don’t forget the extra “Vehicle protection” fuse.

- The 12V + terminal should NOT be connected to the car fuse box.

• Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with

the same mm2 cable as the positive cable (the same amount of power has to run through it).

Ensure that all paint, undercoating or any other insulation is removed from the area where you

want to make your ground connection to.

• Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and

CD-players have an output terminal for connection of the REM of an amplifier. If you don’t have

such an output, a separate switch must be installed to control your amplifiers on/off function.

E n g l i s h

R C a i n P u t

• Connect the RCA-outputs of your radio to the RCA input terminals of the amplifier. Take good

care that you connect the Right output of your radio to a Right input of your amplifier, and that

you connect the Left output of your radio to a Left input of your amplifier.

s P E a k E R O u t P u t

• The Caliber amplifiers have Stereo/Bridgeable Tri-Mode speaker output terminals. You can

connect the speakers to each channel in stereo mode, and simultaneously connect a sub-woofer

to the speaker terminal in a bridged mode.

• Pay attention in connecting your speakers and/or sub-woofers. Be sure to observe correct

speaker output connections for front, rear and their polarity.

• In the stereo mode, connect the right speaker output to the right speaker and the left to the

left.

Connect the positive (+) output to the positive (+) speaker terminal and the negative (-) output

to the negative (-) speakerterminal.

• In the bridged mode connect the left (+) positive to the positive speaker terminal and the right

(-) negative to the negative speaker terminal.

• Do not use the negative speaker output commonly for left and right speakers (common

ground). Improper polarity causes a loss of bass response.

• Never connect the negative speaker output to the chassis of your vehicle. This can cause severe

damage to your Car Audio System.

a M P l i F i E R a D j u s t M E n t s

• Put the input level adjustment knob to the minimum.

• Put the volume of your radio to 3/4 of the maximum.

• Adjust the Bass Boost to your personal sound.

• Now adjust the input level of the front channel. Slowly turn up the input level and listen care-

fully untill you hear the amplifier begin to distort. A Caliber Amplifier “clips” very softly, so this

can sometimes be a difficult adjustment. If you have turned up the Bass Boost to much, the

amplifier will start clipping immediatly. In that case you must turn back the Bass Boost and start

adjusting the inputlevel again. You will hear that the Bass you wanted can be required in this way.

C a l i b E R w a R R a n t y

Due to the complexity of our products, we strongly recommend that this amplifier is installed

by your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for

12 months from the date of purchase.

If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow

our guidelines, you’ll get the best result. Our warranty, however, will be limited to and not exceed

30 days from the date of purchase.

Product specificaties

Merk:	Cyber Acoustics
Categorie:	Speaker
Model:	CA-2050
Kleur van het product:	Zwart
Gewicht:	680.3886 g
Breedte:	85.852 mm
Diepte:	203.2 mm
Hoogte:	200.152 mm
Snoerlengte:	1.8288 m
Aan/uitschakelaar:	Ja
Type aansluitplug:	3,5 mm
Connectiviteitstechnologie:	Bedraad
Type stroombron:	AC
Gemiddeld vermogen:	3 W
Volumeregeling:	Draaiknop
Hoofdtelefoonuitgangen:	1
Ingang stroom:	Ja
Aanbevolen gebruik:	PC
3,5mm-connector:	Ja
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Tafelblad/Boekenplank
Aantal drivers:	2
Diameter driver subwoofer (imperiaal):	2 "
Diameter driver:	609.6 mm
AirPlay:	Nee
Driver cone material:	Titanium
Multi-Room Streaming (MRS)-ondersteuning:	Nee