Crest Audio Versarray Pro 218 Handleiding

Crest Audio Speaker Versarray Pro 218

Lees hieronder de 📖 handleiding in het Nederlandse voor Crest Audio Versarray Pro 218 (80 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/80
1
Versarray™ Pro 112
Powered Enclosure
Product Specifications
e Crest Audio® Versarray™ Pro 112 Powered Ribbon Tweeter Line Source Array speaker system consists of a 12” Neo Black Widow®
woofer combined with a Neodymium based Peavey RD™ 2.6 MK III ribbon tweeter in a cabinet with a simple, quick, yet exible rigging
system. Designed to provide modular coverage of small to medium venues, and intended for use with the companion Crest AudioÂŽ
Versarray™ Pro Sub models, the Versarray™ Pro 112 oers excellent versatility with a very high performance capability. e two-way
system consists of the following driver components: a Peavey® 12” Black Widow ® Neo series woofer with Neodymium magnet struc-
ture. Capable of over 500W of continuous power handling (AES Std 2-1984), the woofer can handle a lot of sheer power. e high
frequencies are handled by two Peavey® RD™ 2.6 MK III ribbon tweeters utilizing a composite sandwich ribbon, a Neodymium magnet
system, and a low distortion CLEAR FORM™ waveguide.
Power for bi-amping is supplied by some very ecient power amplier systems, controlled by a sophisticated and rened DSP opera-
tions system with Dante connection capability. Total system power is 3400W total peak power, with 2000W peak power for the woofer,
and 1400W total peak power for the two ribbon tweeters. is sheer power is controlled precisely and processed by a high performance
DSP system, which provides all the crossover and EQ functions, as well as providing all limiting, compression and driver protection du-
ties with unfailing attention to every detail of the music.
A unique set of control buttons on the rear panel allow analog signal input and use without the need for a network controller, by setting
the system for typical use situations via push-button. is feature allows the use of the system without the requirement for a full-blown
digital networking controller or system.
e FlyQWIK™ adjustable rigging system provides for a classic straight line-array conguration, or a number of dierent angling op-
tions, providing easy aiming of the system. Angles between the array modules is adjustable from 0 degrees (straight), to 15 degrees in
2.5 degree increments. Flying and adjusting the coverage angles is all very quick and simple with the new FlyQWIK™ system.
Quick release push-lock pins are supplied with the rigging hardware to couple the Versarray™ Pro 112 modules together and lock the
angles between them into place, as well as for the rigging halo and y bar congurations of a line array. e exibility of the Versarray
system allows the use of anywhere from 1 to 10 Versarray™ Pro 112 modules in conjunction with anything from one Versarray 218 Pro
Sub to as many Versarray 218 or 215 Pro Subs as you can! An optional special groundstack bracket set mounts to the Versarray 218 Pro
Sub, and allows up to three of the Versarray™ Pro 112’s to be mounted on top of the Versarray 218 Pro Sub, and angled upward, for use
on stage in a stadium seating situation.
Features
• 2-way Bi-Amp Ribbon Line Source Array SR System
• 3400 Total Peak watts of system power
• 12” Neo Black Widow® 4” VC Peavey® Woofer
• Exclusive RD™ 2.6 MK III Ribbon Tweeters with Neo magnet and composite material sandwich ribbon
• Ribbon Tweeters mounted to our proprietary CLEAR FORM™ Waveguide
• 90 H by 15 V degree coverage pattern (per one cabinet)
• Modular Line Array System™ for ease of vertical coverage conguration
• MLAS™ EQ Presets provide professional results quickly
• Easy aiming FlyQWIK™ hardware rigging system
• Angle adjustable in 2 1/2 degree increments, from 0 to 15 degrees total angle between adjacent cabinets
• Full complement of DSP based limiting and compression to protect the drivers from overdrive conditions
• Fan cooled for maximum reliability
• Inputs are analog XLR in and/or Dante Ethernet audio network in.
• Analog Output ru connector is a male XLR
• Analog signal input use without the need for a digital network controller, via the use of rear panel push-button set-up.
• 18 mm 13 ply Baltic Birch enclosure with steel inner brackets
• Injection molded cabinet end caps, made from high impact material.
• Hammerhead™ polyurea black nish and black powder-coated cloth lined grilles
2
Frequency Response, 1 meter on-axis,
swept-sine in anechoic environment: 100
Hz to 20 kHz (Âą3 dB, with processing)
Usable Low Frequency limit (-10 dB
point): 85 Hz (with processing)
Power Amplifier Output:
3400 Total Peak watts* for the system
2000 Peak watts* for woofer
1400 Peak total watts* for tweeters
1700 Total watts* sine wave
1000 watts* sine wave for woofer
700 total watts* sine wave for tweeters
*Output duration is limiter controlled
Sound Pressure Level, 1 Watt, 1 meter in
anechoic environment:
Low Frequency Section: 97 dB SPL,
(2.83 V input)
High Frequency Section: 101 dB SPL,
(2.0 V for 4 ohm load)
Maximum Sound Pressure Level (1
meter) * :
Low Frequency Section: 127 dB SPL
continuous, 130 dB SPL peak
High Frequency Section: 128 dB SPL
continuous, 131 dB SPL peak
*Note: This spec is for one cabinet at 1
meter, a line array of 6 units has much
higher output at distance due to line
source effect where SPL falls off at 3 dB
per distance doubling rather than 6 dB.
Nominal Radiation Angle measured at
-6 dB point of polar response:
90 degrees Horizontal by 15 degrees
Vertical (One cabinet only, straight line
array of more than 1 cabinet narrows
vertical dispersion accordingly)
Transducer Complement:
Low Frequency Section: 1x 12 in.
Woofer, 1244 Neo Black Widow® 4” VC
PeaveyÂŽ Woofer, in a sealed box
High Frequency Section: 2x 4.75
in. Ribbon Tweeters, Two RD™ 2.6
Mk III PeaveyÂŽ Ribbon Tweeters, on a
waveguide
Transducer Nominal Power Handling:
Low Frequency Section: 500 W
continuous; 1,000 W program; 2,000 W
peak
High Frequency Section: 120 W
continuous; 240 W program; 480 W
peak
Box Tuning Frequency (Sealed): Low
Frequency Section: 88 Hz
Electroacoustic Crossover Point, Sub –
Low Frequency: 125 Hz at 24 dB/octave
Low Frequency – High Frequency: 1950
Hz at 24 dB/octave
Transducer Impedance (Z):
Low Frequency Nominal: 8 ohms
High Frequency Nominal: 4 ohms
Signal Input Connections: Analog XLR
in and/or Dante Ethernet audio network
in.
Enclosure Materials & Finish: 18 mm
13 ply Baltic Birch plywood finished in
a tough Hammerhead™ polyurea black
finish, with injection molded end caps
and horn, with a perforated steel grille
finished in black powder coat paint and
a cloth liner inside.
Inner steel frame and backing plates for
rigging hardware.
Mounting provisions: Custom array
brackets and hardware, and a custom
array angle adjustment system are
included with each module. Quick
release push-lock rigging pins are
included with each cabinet.
Flown Rigging Halo sold seperately.
Dimensions (H x W x D):
Front: 15.13 in. x 25.06 in. x 15.19 in.
384 mm x 637 mm x 386 mm
With Rigging hardware and Pins: 15.13
in. x 27.13 in. x 16.75 in.
321 mm x 689 mm x 426 mm
Net Weight: 75 Lbs. (34.1 kg) {includes
all cabinet associated rigging hardware
for each cabinet, including quick-loc
pins, etc}
Companion Subwoofers (sold
separately): Crest Audio® Versarray™
215 Pro Powered Sub with double 15”
LowRider™ Peavey® woofers subwoofer,
Crest AudioÂŽ Versarray 218 Pro Powered
Sub with double 18” LowRider™ Peavey®
woofers subwoofer.
Flying/Rigging Options:
Crest Audio® Versarray™ Mk III HALO
Crest Audio® Versarray™ Mk III FLY
BAR, 6FT LENGTH
Crest Audio® Versarray™ Mk III SUB
SUPPORT FRAME
Crest Audio® Versarray™ Mk III FLY
BAR, 2FT LENGTH
Additional Power Amp Specifications
THD: Typically less than 0.1%
DSP Section Specifications:
Sampling frequency: 96 kHz
Bit Depth: 24 bits for ADC/DAC
Latency: 3.6 ms typical
Rear Panel Controls and
Connections
System Settings Group
Volume Buttons
0 dB to -6 dB in 2 dB increments,
controlled by Up and Down buttons.
Status LED’s indicate which gain level is
currently in effect.
Sensitivity Buttons
Select either +12 dBu or +6 dBu input
sensitivity
Status LED’s indicate which gain level is
currently in effect.
Array Count Button
One button cycles through array count
of 2, 3, 4 or 6+
Status LED’s indicate what number is
currently active
HF Boost Button
Engages or Disengages a set amount of
High Frequency Boost
Status LED indicates if boost is active
or not.
Low Mid Button
Toggles between Indoor and Outdoor
settings.
Status LED’s indicate which mode is
active.
Audio Group
Female XLR input jack, Male XLR
Output/Thru jack
Network Group
Primary Ethernet IN, RJ45 jack
Secondary Ethernet in/out, RJ45 jack
Both have LED indication of
network activity, built into the jack body.
Separate red and green SYNC LED’s
indicate if the unit is syncd with the
control interface or not.
Assign Network I.D. Buttons
Two push buttons to change the
network ID of the unit.
Two digit hexadecimal number ID
possible (255 different ID’s)
Power Group
NeutrikÂŽ powerCONÂŽ TRUE1 TOP,
appliance inlet connector
NeutrikÂŽ PowerCONÂŽTRUE1 TOP,
appliance outlet connector
ON/OFF Power Switch
SPECIFICATIONS Versarray
™
PRO 112
3
Rear Panel Display

Product specificaties

Merk: Crest Audio
Categorie: Speaker
Model: Versarray Pro 218

Heb je hulp nodig?

Als je hulp nodig hebt met Crest Audio Versarray Pro 218 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Crest Audio

Crest Audio

Crest Audio CPL 10+ Handleiding

1 December 2024
Crest Audio

Crest Audio CPL 6+ Handleiding

27 Mei 2023
Crest Audio

Crest Audio CPL 5C+ Handleiding

16 Mei 2023
Crest Audio

Crest Audio CPL 8T Handleiding

30 April 2023
Crest Audio

Crest Audio Versarray PRO 215 Handleiding

25 April 2023
Crest Audio

Crest Audio CPL 6T Handleiding

22 April 2023
Crest Audio

Crest Audio CPL 265B+ Handleiding

20 April 2023
Crest Audio

Crest Audio CPL 8+ Handleiding

16 April 2023
Crest Audio

Crest Audio Versarray 218 MKIII Handleiding

14 April 2023
Crest Audio

Crest Audio CPL 25C+ Handleiding

13 April 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Bose

Bose DesignMax DM5P Handleiding

2 December 2024
Yamaha

Yamaha CHR12 Handleiding

2 December 2024
Yamaha

Yamaha DHR12 Handleiding

2 December 2024
Yamaha

Yamaha DHR15M Handleiding

2 December 2024
Yamaha

Yamaha CHR15M Handleiding

2 December 2024
Yamaha

Yamaha True X Speaker 1A WS-X1A Handleiding

2 December 2024
Yamaha

Yamaha Stagepas 100 Handleiding

2 December 2024
Yamaha

Yamaha NS-2000A Handleiding

2 December 2024
Yamaha

Yamaha DXS15XLF-D Handleiding

2 December 2024
Yamaha

Yamaha DZR15-D Handleiding

2 December 2024