Crest Audio Versarray 112 MKIII Handleiding

Crest Audio Speaker Versarray 112 MKIII

Lees hieronder de 📖 handleiding in het Nederlandse voor Crest Audio Versarray 112 MKIII (32 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/32
1
Versarray™ 112 Mk III
Passive Enclosure
Product Specifications
e Versarray™ 112 Mk III Passive Ribbon Tweeter Line Source Array speaker system consists of a 12” Neo Black
Widow® woofer combined with a Neodymium based Peavey RD™ 2.6 Mk III ribbon tweeter in a cabinet with a
simple, quick, yet exible rigging system. Designed to provide modular coverage of small to medium venues,
and intended for use with the companion Versarray™ Mk III Sub models, the Versarray™ 112 Mk III oers ex-
cellent versatility with a very high performance capability. e two-way system consists of the following driver
components: a 12” Black Widow® Neo series woofer with Neodymium magnet structure. Capable of over 500W
of continuous power handling (AES Std 2-1984), the woofer can handle a lot of sheer power. e high frequen-
cies are handled by two Peavey® RD™ 2.6 Mk3 ribbon tweeters utilizing a composite sandwich ribbon, a Neo-
dymium magnet system, and a low distortion CLEAR FORM™ waveguide.
Designed to be used in conjunction with a compatible DSP based loudspeaker signal processor, such as a Peavey
Digitool™, Nion® or MediaMatrix® system, with the Peavey factory settings in use, the Versarray™ 112 Mk III can
perform to modern standards of excellence, and handily exceed the competitions audible performance.
e FlyQWIK™ fully articulated hardware rigging system provides for a classic straight line-array conguration,
or a number of dierent angling options, providing easy aiming of the system. Angles between the array modules
is adjustable from 0 degrees (straight), to 15 degrees in 2.5 degree increments. Total angle possible between two
cabinets is 15 degrees.
Quick-lock pins are supplied with the rigging hardware to couple the Versarray™ 112 Mk III modules together
and lock the angles between them into place, as well as for the rigging halo and y bar congurations of a line
array. e exibility of the Versarray™ system allows the use of anywhere from 1 to 10 Versarray™ 112 Mk III
modules in conjunction with Versarray™ 218 Mk III Subs. An optional special groundstack bracket set mounts
to the Versarray 218 Mk III Sub, and allows up to three of the Versarray™ 112 Mk III ‘s to be mounted on top of
the Versarray 218 Mk III Sub, and angled upward, for use on stage in a stadium seating situation.
Features
• 2-way Bi-Amp Ribbon Line Source Array SR System
• 12” Neo Black Widow® 4” VC Woofer
• 1000 watt program, 2000 watt peak power handling
• Ribbon Tweeters with Neo magnet and composite material sandwich ribbon
• Ribbon Tweeters mounted to our proprietary CLEAR FORM™ Waveguide
• 90 H by 15 V degree coverage pattern (per one cabinet)
• Easy aiming FlyQWIK™ hardware rigging system
• Angle adjustable in 2 1/2 degree increments, from 0 to 15 degrees total angle between adjacent cabinets
• Sound Guard™ tweeter protection, series capacitor for reliability
• Inputs are two Neutrik® Speakon® 4 pin jacks in parallel
• 18 mm 13 ply Baltic Birch enclosure with steel inner brackets
• Injection molded cabinet end caps, made from high impact material.
• Hammerhead™ polyurea black nish and black powder-coated cloth lined grilles
2
Frequency Response, 1 meter on-axis,
swept-sine in anechoic environment:
100 Hz to 20 kHz (Âą3 dB, with
processing)
Usable Low Frequency limit, -10 dB
point: 85 Hz (with processing)
Power Handling:
Low Frequency Section: 500 W
continuous 1,000 W program 2,000 W
peak
High Frequency Section: 120 W
continuous 240 W program 480 W
peak
Sound Pressure Level, 1 Watt, 1 meter
in anechoic environment:
Low Frequency Section: 97 dB SPL,
(2.83 V input)
High Frequency Section: 101 dB SPL,
(4.0 V input for 16 ohm wiring)
Maximum Sound Pressure Level (1
meter) * :
Low Frequency Section: 124 dB SPL
continuous 130 dB SPL peak
High Frequency Section: 122 dB SPL
continuous 128 dB SPL peak
*Note: This spec is for one module at 1
meter, a line array of 6 units has much
higher output at distance due to line
source effect where SPL falls off at 3 dB
per distance doubling rather than 6 dB
Nominal Radiation Angle measured
at -6 dB point of polar response: 90
degrees Horizontal by 15 degrees
Vertical (One module only, straight line
array of more than 1 module narrows
vertical dispersion accordingly)
Transducer Complement:
Low Frequency Section: 1x 12 in.
Woofer, 1244 Neo Black Widow® 4” VC
Woofer, in a sealed box
High Frequency Section: 2x 4.75
in. Ribbon Tweeters Two RD™ 2.6
Mk III Peavey Ribbon Tweeters, on a
waveguide
Box Tuning Frequency (Sealed): Low
Frequency Section: 88 Hz
Electroacoustic Crossover Point, Peavey
Active Digital Crossover:
(Applies to VSX™, Digitool® and Nion®/
MediaMatrixÂŽ settings provided by
Peavey)
Sub – Low Frequency: 125 Hz at 24dB/
octave
Low Frequency – High Frequency:
1950 Hz at 24dB/octave
Recommended Active Crossover
Frequency Region and Slope: Sub –Low
Frequency: 125 Hz at 24dB/octave LR
Low Frequency –High Frequency: 2000
Hz at 24dB/octave LR
Impedance (Z):
Low Frequency: Nominal: 8.0 Ohms,
Minimum: 6.5 Ohms
High Frequency: Nominal: 16 Ohms,
Minimum: 13.6 Ohms
(Special Note: Ribbon tweeters
are capacitor coupled so use with
switching amps is allowed.)
Input Connections: 2x NeutrikÂŽ 4-pin
SpeakonÂŽ jack
Enclosure Materials & Finish: 18 mm
13 ply Baltic Birch plywood finished
in a tough Hammerhead™ polyurea
black finish, with injection molded
end caps and horn, with a perforated
steel grille finished in black powder
coat paint and a cloth liner inside.
Inner steel frame and backing plates
for rigging hardware.
Mounting provisions: Custom array
brackets and hardware, and a custom
array angle adjustment system are
included with each module. Quick
release pins are included with each
cabinet.
Dimensions (H x W x D):
Front: 15.13 in. x 25.06 in. x 15.19 in.
384 mm x 637 mm x 386 mm
With Rigging hardware and Pins:
15.13 in. x 27.13 in. x 16.75 in.
321 mm x 689 mm x 426 mm
Net Weight: 66 Lbs. (30.0 kg)
{includes all cabinet associated
rigging hardware for each cabinet,
including quick-lock pins, etc.}
Companion Subwoofers (sold
separately): Versarray™ 218 Mk III
Sub double 18” Lo Max® woofer
subwoofer
Optional Accessories:
3 foot speaker cable, with 16 gauge 4
conductor wires with 4-pin to 4-pin
Neutrik plugs (Peavey part number
00585240); and 10mm Quick Release
Positive Lock Pins for array rigging.
Flying/Rigging Options:
Versarray™ Mk III HALO
Versarray™ Mk III FLY BAR, 6FT
LENGTH
Versarray™ Mk III SUB SUPPORT
FRAME
Versarray™ Mk III FLY BAR, 2FT
LENGTH
SPECIFICATIONS Versarray
™
112 Mk III
3
Figure B Directivity Index
Frequency [Hz]
Level [dB]
Figure C Horizontal Beam Width
Frequency [Hz]
Angle Degree
Frequency [Hz]
Figure D Vertical Beam Width
Angle Degree
Frequency [Hz]
dB SPL
Figure A Frequency Response


Product specificaties

Merk: Crest Audio
Categorie: Speaker
Model: Versarray 112 MKIII

Heb je hulp nodig?

Als je hulp nodig hebt met Crest Audio Versarray 112 MKIII stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Crest Audio

Handleiding Speaker

Nieuwste handleidingen voor Speaker