Conair ITH93 Handleiding

Conair Niet gecategoriseerd ITH93

Lees hieronder de 📖 handleiding in het Nederlandse voor Conair ITH93 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Model ITH93

I N F R A

I N F R A R E D T H E R M O M E

R E D T H E R M O M E

R E D T H E R M O M E T E R

T E R

I N F R A R E D T H E R M O M E T E R

FOREHEAD

Instruction

Booklet

For your safety

and continued

enjoyment of

this product,

always read the

instruction

booklet carefully

before using.

TROUBLESHOOTING AND

DISPLAY ERROR MESSAGES

Battery voltage

is too low

System

error

Measured

temperature

is too high

Measured

temperature

is too low

Replace battery

as soon

as possible

Contact your

local dealer

Stop measurement

SYMBOL REASON SOLUTION

CLASSIFICATION

• Internally powered equipment

• Type BF applied part: Probe

• IP22

• Not category AP / APG equipment

• Mode of operation: continuous operation

KEY TO SYMBOLS

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury

Indicates a hazardous situation which, if not

avoided, may result in minor or moderate injury

Addresses practices not related to personal

injuries, such as product and/or property

damage

Do not dispose of this product in municipal

waste. Collection of such waste separately

for special treatment is necessary

Refer to instruction manual/booklet

Degree of protection against harmful ingress of

particulate matter and water.

Serial number

The package should be protected from rain

The package contains fragile products; please

handle with care

Transport package should be upright

The maximum stacking layer of the same

package; 5 means the layer limit

PRODUCT SPECIFICATIONS

Measure range: 89.6˚–109.4˚F (32˚–43˚C)

Accuracy: ±0.4˚F, 96.8˚F~102.2˚F (±0.2˚C

36–39˚C), outside the range

±0.5˚F±0.3˚C

Resolution: 0.1˚F/0.1˚C

Unit: ˚F/˚C (the default unit is ˚F/0.1˚F)

Measure time: 1 second

Measure distance: 0–2 inch from the center of

forehead between the eyebrows

Memory: 32 sets memories

Work

environmental: Temperature 50˚–104˚F (10˚–40˚)

Relative humidity ≤ 85%RH

Atmospheric pressure 70~106KPa

Storage

environmental: Temperature: -4˚–+131˚(-20˚–+55˚C)

Relative humidity ≤93%RH

Atmospheric pressure 70–106KPa

Power AA(1.5Vx2),d.c.3V

Product size 109.6mm x 44mm x 152.9mm

Product weight 95g (not including batteries)

SUPPLIER’S DECLARATION OF CONFORMITY

Brand: Conair

Model No.: ITH93

Description: Infrared Forehead Thermometer

Responsible Party: Conair Corporation, 150 Milford

Road, East Windsor, NJ 88520

(609) 426-1300

Standards: FCC Part 15 Subpart B, ANSI C63.4-2014

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause unde-

sired operation.

Date of issue:

FCC MARKINGS:

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

CAUTION: Any changes or modifications not expressly

approved by Conair Corporation, the manufacturer of

this product and the party responsible for compliance,

could void the user’s authority to operate the equip-

ment. This thermometer is not a toy

LIMITED THREE YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your unit

free of charge for 36 months from the date of

purchase if the appliance is defective in

workmanship or materials.

To obtain service under this warranty, return the

defective product to the service center listed, together

with your purchase receipt and $7.00 for shipping

and handling. California residents need only provide

proof of purchase and should call 1-800-3-CONAIR

for shipping instructions. In the absence of a pur-

chase receipt, the warranty period shall be 36 months

from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED

IN DURATION TO THE 36-MONTH DURATION

OF THIS WRITTEN, LIMITED WARRANTY.

Some states do not allow limitations on how

long an implied warranty lasts, so the above

limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH

OF THIS OR ANY OTHER WARRANTY,

EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or

limitation of special, incidental, or consequential

damages, so the above limitation may not apply

to you. This warranty gives you specific legal rights,

and you may also have other rights, which vary from

state to state.

Belter model number TE-93

Shenzhen Belter Health Measurement and

Analysis Technology Co.,Ltd.

702/704, Block C,

Tsinghua Unis Science

No.13 Langshan Rd,

Hi-Tech Industrial Park(north). Nanshan District, 518057

Shenzhen

People’s Republic of China

SERVICE CENTER

Conair Corporation

Service Department

1 Cummings Point Rd.

Stamford, CT 06902

203-351-9000

For information on any Conair product, call

1-800-3-CONAIR or visit us on the web at

www.conair.com

Please register this product at

www.conair.com/registration

Made in China

20PA074606 IB-16937

Thank you for purchasing the ConairCare Infrared Forehead

Thermometer (ITH93). This product features the latest tech-

nology and has been tested according to international

medical device standards. It has been cleared by the FDA

for home and professional use. The thermometer’s unique

technology enables stable and accurate measurements

every time. This product is designed specifically to monitor

body temperature for use at home or in clinical settings.

Please read the instruction manual carefully and keep it in

a safe place for reference.

INDICATIONS FOR USE

The ITH93 is a non-sterile, reusable, clinical electronic

thermometer using an infrared sensor to detect human

body temperature on people of all ages for home and

professional use.

WARNINGS & PRECAUTIONS

Never use the thermometer for purposes other than

those it has been intended for.

The use of this thermometer is not intended as a sub-

stitute for a consultation with your healthcare provider.

If you are concerned about your health, please see

your physician. Elevated temperature may signal a

serious illness, especially in older individuals, people

with compromised immune systems, and infants.

In order to properly diagnose an elevated temperature,

it is important to know an individual’s normal body

temperature. We suggest taking several readings

when the person is healthy, to set a baseline for their

normal temperature.

Infrared thermometers cannot be used to diagnose

COVID-19 or other illnesses. Infrared thermometers

can identify individuals with higher than average body

temperatures compared to a sample population. Only

a medical professional can determine whether an

individual is experiencing an abnormal medical condi-

tion or illness.

Note that an abnormal medical condition may be

present even when an individual does not show a

fever. When in doubt, consult your physician.

Follow general safety guidelines when using this

thermometer on children. Do not allow children to

take their temperature unattended. This is a not toy.

We recommend not using this thermometer on chil-

dren less than 3 months of age.

Do not immerse this thermometer in water or other

liquids. Follow the instructions in the “Cleaning and

Maintenance” section to clean and disinfect the ther-

mometer.

The device is made of precision parts. Do not disman-

tle, re-assemble or modify the thermometer in any

way. Do not drop the thermometer and protect it from

strong impacts.

Do not use this thermometer if the sensor is broken. If

the device is broken, do not attempt to repair it your-

self. Contact the customer service center.

Do not use this thermometer in the presence of flam-

mable anesthetic mixtures with air or with oxygen or

nitrous oxide. CAUTION

Keep the device away from direct sunlight. Store in a

dry and dust-free environment, ideally within a

storage temperature range of to 1314˚F ˚F

(-20 ).˚ C to 55C˚

Before taking temperature readings, please make

sure the sensor surface is clean. If there is visible dust

or dirt, you may clean the surface with a cotton swab

dipped in rubbing alcohol before using the device.

After cleaning the sensor head with alcohol, it is rec-

ommended to leave the device for a few minutes until

the alcohol evaporates and the sensor head returns to

its normal temperature. We suggest cleaning the ther-

mometer sensor after use, to ensure measurement

accuracy and to avoid potential cross-contamination.

To make sure the measurement result is accurate,

wait at least 30 seconds after each measurement

before you measure again.

Because babies are slower at adapting to temperature

changes in the environment, if drastic temperature

changes are observed, it is best to wait a few minutes

in the same environment until the baby’s body tem-

perature becomes stable before taking any tempera-

ture readings to ensure the most accurate results.

It is recommended to take 3 temperature readings

and reference the highest recorded measurement for

babies between 3 months to 3 years of age, or for

first-time users of the device.

The device requires no calibration.

Remove batteries if the equipment is not likely to be

used for some time.

The user must check that the equipment functions

safely and see that it is in proper working condition

before use.

Do not operate the product out of operating condi-

tions or out of the operating temperature range, as it

may cause measurement value anomalies or mal-

function.

HOW THE THERMOMETER WORKS

This thermometer detects infrared energy radiated

from the skin and tissue of the forehead. Temperature

readings taken in the center of the forehead (between

and slightly above the eyebrows) will provide the

most accurate measurements. This thermometer has

been tested and proven to be safe and accurate

when used as directed in this instruction manual.

This device has settings that alert you to a tempera-

ture above normal.

Normal temperature varies from person to person, by

age, and even by time of day and activity. It is best to

establish a “normal” temperature range for each user

of the thermometer while the person is feeling well.

We suggest taking readings in the morning and in the

late afternoon and averaging them to get a “normal”

temperature. Record that temperature so you can use

it to compare against temperatures measured for

that person when they are not feeling well. Note that

normal body temperatures tend to decrease with

age. The ConairCare thermometer allows you to cus-

tomize your high temperature alert settings depend-

ing on your own normal temperature.

Generally, temperatures in the range of 96.4 ˚– 99.4˚F

(35.8-37.4˚C) are considered normal, a temperature

between 99.5˚–101.3˚F (37.5 ˚C – 38.5 ˚C) is consid-

ered a light fever and temperatures over 101.3 ˚F

(38.5 ˚C) are considered a fever.

The ConairCare thermometer features automatic

ambient temperature compensation and forehead

temperature dynamic compensation.

GETTING METER

Sensor

Trigger

Battery

cover

Battery level

Memory

Body Mode

Sound ON

Temperature

˚ ˚F/ C Mode

Last reading

LCD

SETTING UP YOUR THERMOMETER

Press trigger button on the handle to turn on device.

If the thermometer display does not light up, open the

battery door on the bottom of the handle and make

sure the batteries are correctly installed with respect

to polarity. Close the battery door and press the but-

ton again. The display will light up. When the ther-

mometer is turned on and the display lit, press and

hold the “set” key to enter the function settings.

1. Selecting temperature units

The screen will display F1 and then show the tem-

perature unit (˚F/ ˚C). The default is ˚F. To change to

˚C, press the “+” button. To change back to ˚F, press

the “-” button. Press “set” to advance to the fever

alert setting.

2. Setting the fever alert

The screen displays F2 and then shows the current

fever alert temperature. The default setting is 99.1 ˚F.

To increase the threshold, press the “+” button. To

decrease the threshold, press the “-” button. Press

“set” to advance to the temperature offset value

setting.

3. Setting the temperature offset value

The screen displays F3 and then shows the offset

value. The default setting is 0.0 ˚F/C. Press “set” to

leave temperature offset in the default setting or “+”

to increase or “-” to decrease. Then press “set” to

enter the auditory alert mode. We recommend leaving

the default 0.0 setting in place.

4. Auditory alert setting (beep)

The display will show F4 and then show whether the

beep function is on or off. The default is ON. To turn it

off, press the “-” button. Press the “+” button to turn

the beep on. Press “set” to advance to the backlight

setting.

5. Setting the backlight

The display will show F5 and show whether backlight

is on or off. The default is ON. To turn the backlight

off, press the “-” button. Press the “+” button to turn

the backlight back on. Press “set” to exit the function

setting mode. The display goes dark.

BEFORE TAKING A

TEMPERATURE READING

Clean the skin of the forehead and make sure the

area is free of hair, sweat, cream or makeup.

Wait at least 30 minutes after strenuous exercise to

take your temperature.

Take the temperature in a room that does not have

significant changes in air flow, such as a room with

large fans and air conditioners. Do not take your

temperature near heat sources, such as radiators or

heat registers.

The body’s temperature adapts to the environment.

Allow at least 20 minutes to adjust to room tempera-

ture if a person is entering a room that is significantly

warmer or cooler than the room they were in

previously.

MEASURING FOREHEAD TEMPERATURE

Point the front of the thermometer (sensor head) at

the center of the person’s forehead, no more than

2 inches (5cm) away from the skin, and press the

button on the handle. A beep indicates that the mea-

surement is complete and the measurement value is

shown on the display. In order to avoid human error,

we suggest that you take multiple measurements at

least 20 seconds apart and average them.

3 5cm

0-2" ( 5 cm)0-

Fever Alerts

When the measured forehead temperature exceeds

the preset fever threshold temperature, the thermom-

eter will emit several beeps in a row, alerting you to a

high temperature. The fever threshold temperature

can be adjusted in the function settings (see above).

STORED READING RECALL

Turn the thermometer on by

pressing the trigger button on

the handle. The display lights

up. The saved temperature

readings (up to 32 readings)

are displayed in the lower

left-hand corner of the display

(reading number) and the

lower right hand corner (temperature). Press the “+”

and “-” buttons, to move through the list of saved

readings. Press and hold the +/- buttons to move

through the list more quickly.

AUTOMATIC SHUT DOWN

This thermometer is equipped with a battery-saving

automatic shutdown feature: after 15 seconds with-

out any user action, the thermometer will power

down. You can turn it back on by simply pressing the

trigger button on the handle.

BATTERY REPLACEMENT

This product uses 2 AA alkaline batteries. When the

display shows a battery icon, the batteries are low. To

replace the batteries, push the battery cover on the

bottom of the handle in the direction of the arrow.

Take out the old batteries and install the new batter-

ies, making sure the polarity is correct (note the “+”

and “-” signs on the metal plate inside the battery

door). Close the battery door and properly dispose of

the batteries. If the thermometer is not used for more

than 3 months, remove the batteries to prevent

potential damage from battery fluid.

BATTERY SAFETY

1. This product requires 2 AA batteries.

2. Since batteries are sensitive to high temperatures,

keep them in a cool, dry place when storing them.

3. Battery contacts need to be clean, both on the

battery and in the appliance, before installation.

4. Batteries should be removed from the appliance

when not being used for long periods of time

(months).

5. Never recharge non-rechargeable batteries.

6. Use only the power cord supplied with the

appliance.

7. Be careful to install (+) and (-) to the correct plus

and minus on device.

8. Replace all old batteries at one time. Do not mix

old and new.

9. Remove discharged batteries immediately to

avoid leakage.

10. Never put batteries into a fire.

11. Switch off devices after use.

12. Keep batteries away from children, especially the

batteries that are small enough to ingest.

13. If a battery is ingested, seek immediate

medical help.

14. Never open, crush, puncture or disassemble

batteries.

15. Dispose of batteries according to any state

and Local regulations.

16. Do not dispose of rechargeable batteries as

solid waste.

CLEANING AND MAINTENANCE

Check whether the battery level is sufficient before

each use. If the battery is low (display shows battery

icon) change the batteries and then take the tem-

perature.

Before each use, check the equipment casing for

damage. If it is damaged, do not use.

Wipe with a soft, dry cloth after each use. If the ther-

mometer is dirty, you may wipe the unit with a damp

cloth moistened with water or neutral detergent and

then wipe it with a dry cloth. Avoid water entering the

body of the thermometer, so that the internal elec-

tronic components do not get damaged.

This no-contact thermometer does not require disin-

fection. If you are concerned about contamination,

however, you may clean the thermometer with 75%

alcohol before and after use.

Do not use volatile oil, paint thinner, and other chemi-

cal solvents to wipe the product.

Product specificaties

Merk:	Conair
Categorie:	Niet gecategoriseerd
Model:	ITH93

Heb je hulp nodig?

Als je hulp nodig hebt met Conair ITH93 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Conair

Conair CB06 Handleiding

20 November 2024

Conair DF22DCM Handleiding

20 November 2024

Conair Style Chemistry CB03 Handleiding

20 November 2024

Conair CB08 Handleiding

20 November 2024

Conair Bubble Wand CB05 Handleiding

20 November 2024

Conair Style Chemistry CB01 Handleiding

20 November 2024

Conair Care HM16 Handleiding

20 November 2024

Conair Jet Hydro Spa HYD100 Handleiding

20 November 2024

Conair BC191N Handleiding

18 November 2024

Conair MiniPRO CS80N Handleiding

30 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Vitec MGW Diamond-HX OG Handleiding

23 November 2024

Electrolux STA9 Handleiding

23 November 2024

Electrolux UMP3 Handleiding

23 November 2024

Electrolux ZS70GL Handleiding

23 November 2024

Bosch HEZ8TK36UC Handleiding

23 November 2024

Bosch HEZ8ZZ36UC Handleiding

23 November 2024

Bosch HDZIT301 Handleiding

23 November 2024

Bosch HEZBS301 Handleiding

23 November 2024

LG LX-330 Handleiding

23 November 2024

Stamos S-PLASMA 60U Handleiding

23 November 2024