Cointra Thermex Blitz IBL Handleiding

Cointra Ketel & boiler Thermex Blitz IBL

Lees hieronder de 📖 handleiding in het Nederlandse voor Cointra Thermex Blitz IBL (9 pagina's) in de categorie Ketel & boiler. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

Before the first using your electric storage water heater, carefully read this operation

manual and pay special attention to paragraphs marked with «Attention» symbol.

Dear customer! Congratulations on your purchase of THERMEX electric water heater. We are

convinced that a wide range of our electric water heaters will satisfy any of your needs. Use of modern

technologies and the highest quality materials when manufacturing devices have contributed to gaining

popularity and trust to THERMEX trade mark.

THERMEX electric water heaters are designed and manufactured in strict accordance with domestic

and international standards guaranteeing reliability and safety of operation.

Present operation manual applies to THERMEX models series IBL, volume 10, 15 liters. In all

models Silver Heat heating element can optionally be installed. The full name of your heater model of

is specified in section “Manufacturer’s Guarantee” (sub-section "Note of sale") and in the

identification plate on the casing of the heater.

1. Application

Water heater (hereinafter EWH) is designed to provide with hot water for welfare and industrial

facilities that have cold water supply main with appropriate characteristics.

EWH shall be operated in closed heated spaces and is not designed for continuous flowing mode.

2. Main technical characteristics



Maximum cold water main pressure – 0.7 MPa



Minimum cold water main pressure – 0.05 MPa



Parameters of the power supply - single-phase network with voltage (220 V ± 10%) and +1% 50

Hz + 1%



Power of tube heater is adjustable in steps:

1.5 kW - save heating mode

2.5 kW - full heating mode (TURBO mode)



Thread diameter of hot and cold water connecting pipes - ½”



Heater protection class - IPX4

Model

Volume

(l)

Average heating

time

=450 , Т С

(.5 kW)

Permanent

subsistence

loss (kWh/24

Actual annual energy

consumption * (*Permanent

subsistence loss) (kW/h)

IBL 10O, 10U 10 16 min. 0,56 204,4

IBL 15O, 15U 15 28 min. 0,69 251,8

3. Scope of supply

1. Water heater ..................................................

1 pc.

2. Pressure relief valve GP type ............................ 1 pc.

3. Operation manual ........................................ 1 pc.

4. Packaging ...........................................................................1 pc.

5. Anchors for fastening.......................................................... 2 PCs. for each clamping bar

4. Description and principle of operation

EWH consists of the housing, removable flange, safety valve, protective cover and Control Panel.

4.1.

The housing consists of the outer shell, made of plastic, internal tank, thermal insulated with

environmentally friendly polyurethane foam, and two threaded pipes for cold water inlet (blue ring) and

hot water exhaust (red ring).

Internal tank is made of stainless austenitic stainless steel, which ensures high corrosion resistance

and, as a consequence, long operation life.

4.2.

At the removable flange the following is mounted: tubular heater (HEATER), pipe thermostat.

TEH is used to heat water and thermostat provides with possibility to adjust temperature up to +74°

C (± 5° C). Temperature adjustment is made using adjustment knob located on the water heater

control panel (Fig. 1).

The thermal switch is used to prevent overheating and cut off EWH power when water

temperature exceeds +95° C (± 5° c) (fig. 2). EWH housing can heat inthe course of operation.

Two warning lights (button) located on the control panel (fig. 1) of the water heater next to the

temperature adjustment knob indicate operating mode: "POWER" light is on when the save mode

(1.5 kW), and TURBO light - when the full heating mode (2.5 kW). Switching between the modes is

made by pressing TURBO button, when button pressed "TURBO" mode is on, when released – save

mode. EWH power on/off is carried out by POWER button.

4.3.

Safety valve is back-flow valve preventing ingress of water from the water heater to

water main in case of pressure drop in the latter and in case of pressure increase in the tank

when water is heating up, as well as safety valve, relieving excess pressure in tank when water

is heating up. During water heater operation water may leak out of the exhaust outlet pipe of the

safety valve to relieve excessive pressure, which is made for the purpose of water heater

safety. This outlet pipe shall remain open to the atmosphere and be installed constantly down.

and in a non-freezing environment. You shall ensure drainage of water from exhaust pipe safety

valve into the drain, with installation of the corresponding EWH drainage.

It is required regularly (at least once a month) to discharge a small amount of water through the

exhaust pipe of the safety valve into the drain to remove lime deposits and to test the operating

functionality of the valve. Handle is intended to open the valve. It is necessary to control when

operating water heater this handle to be in position closing water draining from the tank.

5. Specifying security measures

5.1.

Electrical safety and corrosion protection of EWH are guaranteed only if there is an effective

earthing in accordance with applicable electric installation rules and regulations.

5.2.

Plumbing pipes and fittings shall conform to parameters of water main and have the required

certificates of quality.

5.3.

When installing and operating EWH the following is not allowed.



To power EWH if EWH is not filled with water.

• To remove the protective cover when the power is on. EN

• Use EWH without grounding or use water pipes as grounding.

• To connect EWH to water main with pressure exceeding 0.7 MPa.

• To connect EWH to the water supply without safety valve.

• To drain water from EWH with power switched on.

• To use spare parts not recommended by the manufacturer.

• To use water from the EWH for cooking.

• To use water containing impurities (sand, small stones), which might lead to EWH and safety

valve breakdown.

• To modify design and installation dimensions of EWH brackets.

• Ambient temperature, where EWH is operated, shall be within the range from 3° c to 40° C.

Water freezing in EWH at negative temperatures cause its malfunction, which is not a guarantee case.

Attention should be paid to children so that they do not play with EWH. EWH is not intended

for use by persons (including children) with limited physical, sensory or mental capabilities, or

by persons who do not know how to use the EWH, except for cases when this happens under

the supervision or instructions by persons responsible for safety of the EWH.

6. Installation and connection

All installation, plumbing and electrical works must be performed by qualified personnel.

6.1.

Arrangement and

installation

EWH installation shall be performed in accordance with marking on the housing and the following

table:

Model Volume (l) Arrangement

IBL-O 10, 15 Pipes down

IBL-U 10, 15 Pipes up

It is recommended to install EWH as close as possible to the place of hot water using to reduce heat loss in the

pipes.

When drilling (making) holes in the wall, you should consider cables, ducts and pipes in the wall.

When choosing EWH installation place take into account total weight of EWH filled with water. Wall

and floor with low carrying capacity shall be reinforced accordingly.

EWH is suspended with housing bracket on the anchor fixed into the wall. Hooks mounting on the

wall shall exclude spontaneous moving of EWH brackets.

To perform maintenance and servicing of EWH the distance from the protective cover to the nearest

surface in the direction of removable flange axis shall be at least 0.5 m.

In order to avoid damage of the user’s and/or third parties’ property in the event of a faulty hot

water system, it is required to install EWH in spaces with waterproofing and drainage to the

sewers, and in no case to place under items exposed to the water under EWH. When placed

in unprotected areas a protective plate (not supplied) with drainage into sewers shall be

installed under the EWH.

Product specificaties

Merk:	Cointra
Categorie:	Ketel & boiler
Model:	Thermex Blitz IBL

Heb je hulp nodig?

Als je hulp nodig hebt met Cointra Thermex Blitz IBL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ketel & boiler Cointra

Cointra Optima 11 D Handleiding

8 April 2024

Cointra Thermex IF Handleiding

8 April 2024

Cointra TNC 10 Handleiding

8 April 2024

Cointra TL Plus 30 S Handleiding

8 April 2024

Cointra Optima COB-10p Handleiding

8 April 2024

Cointra Optima COB-5p Handleiding

8 April 2024

Cointra Thermex ID Handleiding

8 April 2024

Cointra TNC- 100 H Handleiding

8 April 2024

Cointra TNC-15 Handleiding

8 April 2024

Cointra Optima COB-5N Handleiding

8 April 2024

Handleiding Ketel & boiler

Nieuwste handleidingen voor Ketel & boiler

Panasonic DH-6VS1 Handleiding

25 November 2024

Philips AWH1201 Handleiding

24 November 2024

Philips AWH1211 Handleiding

24 November 2024

Philips AWH1200 Handleiding

24 November 2024

Philips AWH1205 Handleiding

24 November 2024

Philips AWH1204 Handleiding

24 November 2024

Rinnai EHPA250VMAWH Handleiding

21 November 2024

Rinnai ECF29i50 Handleiding

21 November 2024

Rinnai ECF19i60 Handleiding

21 November 2024

Rinnai FM10NA Handleiding

20 November 2024