Citizen CAL 6870 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Citizen CAL 6870 (7 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/7
CITIZEN QUARTZ
ALARM CHRONOGRAPH
Model No. AI3XXX
Cal. No. 6870
• INSTRUCTION MANUAL
CTZ-B6813
Thank you for purchasing a CITIZEN QUARTZ
Watch. To ensure correct use, please read these
instructions carefully. Please confirm that the
CITIZEN International Guarantee Card is included
for your possible claim.
1. Name of Components
Refer to diagram of the watch when reading this
section on components. The design may differ
depending on the model.
2. Mode (Display Function) Switching
This watch is equipped with 8 modes consisting of
time, alarm 1, alarm 2, chronograph, 0-position check,
timer, local time and calendar modes. The mode
changes each time the 嘷
Mbutton is pressed. The
current mode can be confirmed with the mode hand.
3. Before Using
Before using your watch, check that the functions of
the watch operate properly by following procedure
(0-position check).
1. Press button 嘷
Mto switch the
watch to the 0-position check
mode [䊳 䊴0 ]. The hour hand,
minute hand, 24H hand,
second hand, date and function
hand will advance rapidly to
the 0-position (base position).
Hour, minute and 24H hands .......... 00:00 (24:00)
Second hand ................................... 00 seconds
Date ................................................. 1st
Function hand .................................. 0-position
(12:00 position)
* Perform the “0-Position Correction” procedure when
any hand is not at the 0-position. If this 0-position is
not correct, the hands will not show the correct
position (such as not returning to “00” when
resetting the chronograph).
✩When one button 嘷A,嘷Bor 嘷Cis pressed while in
the 0-position check mode, the hour, minute,
second and function hands will move to the left
and right following a demonstration program.
<0-Position Correction Procedure>
1. Pull button 嘷
Mout while in the 0-position check mode.
2. Press buttons 嘷A, 嘷Bor 嘷Cto correct the 0-position
of each hand.
The second hand can be corrected by pressing
button 嘷
A.
The date and function hand can be corrected by
pressing button 嘷
B.
* The date will be corrected by one day when the
function hand completes 4 revolutions. The 12:00
position, immediately after the date has changed
to “1”, is the 0-position.
The hour, minute and 24H hands can be
corrected by pressing button 嘷
C.
Corrections can be made rapidly by holding down
any of the buttons.
3. Push button 嘷
Min to the normal position.
* After correcting the 0-position of each hand,
switch to each mode to reset the time, calendar,
alarms and so forth.
0-Position: This refers to the base position
of each hand that enables the watch
to function properly.
4. Setting the Time [TME]
Press button 嘷
Mto switch to the time mode [TME].
1. Pull button 嘷
Mout.
2. Press button 嘷
Ato reset
seconds.
Simultaneous to pressing
button 嘷
A, the second hand
will return to the 0 seconds
position and then start to
move.
3. Press button 嘷Bor 嘷Cto correct the hour, minute
and 24H hands.
Corrections can be made one minute at a time in
the clockwise direction each time button 嘷
Bis
pressed.
Corrections can be made one minute at a time in
the counterclockwise direction each time button
嘷
Cis pressed.
Corrections can be made rapidly by holding
button 嘷Bor 嘷Cdown.
Correct the time by moving the hands in the
closest direction to the correct time.
4. Push in button 嘷
Mto the normal position.
5. Setting the Calendar [CAL]
Press button 嘷
Mto switch to the calendar mode [CAL]
1. Pull button 嘷
Mout.
2. Press button 嘷
Ato correct
the month number.
Correction can be made by
advancing one month each
time button 嘷
Ais pressed.
The month number can be
read directly from the
normal hour positions.
2. (Example: 3:00 ➞March, 1:00 ➞January)
Correction can be made rapidly by holding button
嘷
Adown.
3. Press button 嘷
Bto correct the date.
Correction can be made by advancing one day
each time button 嘷
Bis pressed. Correction can be
made rapidly by holding button 嘷
Bdown.
4. Push button 嘷
Min to the normal position.
6. Use of Quick Set Alarm [AL-1]
The quick set alarm function uses a 24-hour clock.
When the alarm set time is reached, an alarm sounds
for 10 seconds. Once the alarm has stopped
sounding, the alarm set time is cancelled
automatically (alarm off). The alarm can be stopped
by pressing any of buttons 嘷A,嘷Bor 嘷C.
<Quick Set Alarm ON Display>
Press button 嘷
Mto switch to the
alarm-1 [AL-1] mode.
• When the second hand is
stopped at the ON position (23
second position), it indicates that
the alarm is set (alarm ON). The
hour, minute and 24H hands
indicate the alarm set time.
• When the second hand is moving, it indicates that
the alarm has been cancelled (alarm OFF). The
hour, minute and 24H hands indicate the time of
the TME mode.
<Setting the Alarm Time>
Press button 嘷Bor 嘷Cto move the hour, minute and
24H hands to the time at which the alarm is desired
to be set.
• Correction can be made one minute at a time, in the
clockwise direction, each time button 嘷
Bis pressed.
• Correction can be made one minute at a time, in the
counterclockwise direction, each time button 嘷
Cis
pressed.
Correction can be made rapidly by holding button
嘷Bor 嘷Cdown.
Correct the alarm set time by moving the hands in
the closest direction to the desired alarm time.
* When setting the alarm time, be careful that AM and
PM are set correctly by referring to the 24H hand.
<Cancelling Alarm Set Time>
The alarm set time is cancelled by pressing button
嘷
Awhen the alarm is ON.
<Alarm Monitor>
The alarm sound can be monitored by pressing
button 嘷
Ain the Alarm 1 mode when the alarm is OFF.
7. Use of Daily Alarm [AL-2]
The daily alarm also uses a 24-hour clock. Once the
alarm is set, the alarm sounds for 15 seconds at the
alarm set time, once a day. The alarm sound can be
stopped by pressing any of buttons 嘷A,嘷Bor 嘷C.
<Daily Alarm ON Display>
Press button 嘷
Mto switch to the
alarm 2 (AL-2) mode.
The second hand will indicate
either ON (23 second position)
or OFF (19 second position). In
both cases, the hour, minute
and 24H hand will indicate the
alarm set time.
* When setting the time, be careful that AM and
PM are set correctly by referring to the 24H hand.
* Since the date and function hand are
synchronised with each other, the function hand
will turn at when correcting the date.
* Date correction at the end of each month is not
required. However, since February is set at 28
days, date correction must be performed for
February only in leap years.
<Setting the Alarm Time>
1. Pull button 嘷
Mout.
The second hand will indicate the ON position.
2. Press button 嘷Bor 嘷Cto move the hour, minute
and 24H hands to the time at which the alarm is
desired to be set.
• Correction can be made one minute at a time, in
the clockwise direction, each time button 嘷
Bis
pressed.
2. • Correction can be made one minute at a time, in
the counterclockwise direction, each time button
嘷
Cis pressed.
Correction can be made rapidly by holding
button 嘷Bor 嘷Cdown.
Correct the alarm set time by moving the hands
in the closest direction to the desired alarm time.
3. Push button 嘷
Min to the normal position.
* When setting the alarm time, be careful that AM
and PM are set correctly by referring to the 24H
hand.
<Switching Between Alarm ON and OFF>
The alarm will switch between ON and OFF each
time button 嘷Ais pressed with button 嘷Mpulled out.
<Alarm Monitor>
The alarm sound can be monitored by pressing
button 嘷Ain the alarm 2 mode when button 嘷Mis in
the normal position.
8. Use of Chronograph [CHR]
The chronograph is able to measure time up to a
maximum of 59 minutes, 59 and 19/20th seconds in
1/20th increments after which the chronograph
returns to the chronograph reset display and stops.
This chronograph is also able to measure split time.
In the chronograph mode, the hour, minute and 24H
hand as well as date indicate the current time and date.
<Explanation of Display>
Chronograph minutes: Read the function hand.
Chronograph seconds: Read the second hand.
Chronograph 1/20 seconds: The function hand will
change to the 1/20th second display when button 嘷
B
is pressed during the stop or split display. The value
for 1/20th seconds is read at every time.
<Use of Accumulated Elapsed Time Measurement>
1. The chronograph is started and stopped by
pressing button 嘷
A. (Starting and stopping the
chronograph can be repeated as many times as
desired.)
2. The chronograph is started and stopped by
pressing button 嘷
Cwhen it is stopped.
✩A confirmation beep will sound when either the
start, stop or split operation is selected.
<Use of Split Time Measurement>
1. The chronograph is started and stopped by
pressing button 嘷
A.
2. Pressing button 嘷
Cduring measurement displays
the split time for 10 seconds. The next split time
is displayed when button 嘷
Cis pressed again
during display of split time.
3. The chronograph is reset by pressing button 嘷
C
when it is
stopped.
* The chronograph
automatically
returns to the
measuring state
after displaying
the split time for 10 seconds.
✩A confirmation beep tone will sound when either
the start, stop or split operation is selected.
9. Use of Timer [TME]
The timer can be set over a range of 1 to 59 minutes
in 1 minute increments. When measurement of the
set time is completed, the watch beeps for 5 seconds
indicating that the time is up. After the set time has
elapsed, the timer will automatically return to the
same set time. In the timer mode, the hour, minute
and 24H hands as well as the date indicate the
current time and date.
<Timer Setting Procedure>
Press button 嘷
Mto switch to the
timer mode [TMR].
1. Pull button 嘷
Mout.
2. Press button 嘷Bor 嘷Cto set
the timer to the desired time.
Correction can be made one
minute at a time in the
clockwise direction each time
button 嘷
Bis pressed.
Correction can be made one minute at a time in the
counterclockwise direction each time button 嘷
Cis
pressed.
The hands can be advanced rapidly by holding
button 嘷Bor 嘷Cdown.
3. Push button 嘷
Min to the normal position.
* Measurement will continue internally even
when the watch is switched to a different
mode during chronograph measurement.
Measurement will be shown continuing when
the watch is again returned to the chronograph
mode. However, it returns to the reset display
when 60 minutes have elapsed.
Product specificaties
| Merk: | Citizen |
| Categorie: | Horloge |
| Model: | CAL 6870 |
Heb je hulp nodig?
Als je hulp nodig hebt met Citizen CAL 6870 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Horloge Citizen
25 Juni 2024
25 Juni 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
Handleiding Horloge
- Horloge Braun
- Horloge IKEA
- Horloge Casio
- Horloge Epson
- Horloge Huawei
- Horloge Garmin
- Horloge Medion
- Horloge Topcom
- Horloge Ade
- Horloge Adidas
- Horloge Alessi
- Horloge Alpina
- Horloge Armani
- Horloge Ascot
- Horloge Asics
- Horloge Auriol
- Horloge Beper
- Horloge BML
- Horloge Boss
- Horloge Bruno Sohnle
- Horloge Bulova
- Horloge Bushnell
- Horloge Dakota
- Horloge Danish Design
- Horloge Davis
- Horloge Detomaso
- Horloge Diesel
- Horloge Digi-tech
- Horloge Easypix
- Horloge Ebel
- Horloge Edox
- Horloge ELYSEE
- Horloge ESQ
- Horloge ETA
- Horloge Eurochron
- Horloge Ferrari
- Horloge Festina
- Horloge Fila
- Horloge Fitbit
- Horloge Fossil
- Horloge Freestyle
- Horloge GC Watches
- Horloge Geemarc
- Horloge Guess
- Horloge Habitat
- Horloge Haffstreuner
- Horloge Hamilton
- Horloge Hugo Boss
- Horloge ICE Watch
- Horloge Inter-Quartz
- Horloge Invicta
- Horloge Irox
- Horloge Kalenji
- Horloge Karlsson
- Horloge Kogan
- Horloge Krontaler
- Horloge La Crosse
- Horloge Lacoste
- Horloge Lambretta
- Horloge Longines
- Horloge Lorus
- Horloge Lotus
- Horloge Lynx
- Horloge Marc Jacobs
- Horloge Marquant
- Horloge Meister Anker
- Horloge Michael Kors
- Horloge Misfit
- Horloge Mitsubishi
- Horloge Mondaine
- Horloge Movado
- Horloge Naitica
- Horloge Naviforce
- Horloge Nedis
- Horloge Nike
- Horloge Polar
- Horloge Pulsar
- Horloge Pyle
- Horloge QQ
- Horloge Rado
- Horloge Renkforce
- Horloge Rodania
- Horloge Rolex
- Horloge Ronda
- Horloge Seiko
- Horloge Sempre
- Horloge Sinn
- Horloge Skmei
- Horloge Slazenger
- Horloge Speedo
- Horloge Spinnaker
- Horloge Stuhrling
- Horloge Suunto
- Horloge Swatch
- Horloge Tauchmeister
- Horloge TCM
- Horloge Technaxx
- Horloge TFA
- Horloge Ticwatch
- Horloge Timer
- Horloge TimeStyle
- Horloge Timex
- Horloge Tissot
- Horloge Tommy Hilfiger
- Horloge TomTom
- Horloge Torgoen
- Horloge TW Steel
- Horloge Uri Minkoff
- Horloge Velleman
- Horloge Westfalia
- Horloge World Timer Chronograph
- Horloge Xonix
- Horloge Jaguar
- Horloge Junghans
- Horloge Just
- Horloge Olivia Burton
- Horloge Omega
- Horloge Oregon Scientific
- Horloge Orient
- Horloge Clas Ohlson
- Horloge Crivit
- Horloge Zenith
- Horloge Prologue
- Horloge Swiza
- Horloge Victorinox
- Horloge Bering
- Horloge Breitling
- Horloge Breo
- Horloge Brera
- Horloge Calypso
- Horloge Certina
- Horloge Christiaan Van Der Klaauw
- Horloge Christopher Ward
- Horloge Cover
- Horloge Daniel Steiger
- Horloge DMC
- Horloge Dugena
- Horloge Executive
- Horloge Fromanteel
- Horloge Gant
- Horloge Gc
- Horloge Girard-Perregaux
- Horloge Holzkern
- Horloge Hublot
- Horloge HYT
- Horloge IWC
- Horloge Jacques Lemans
- Horloge Klaus Kobec
- Horloge Lars Larsen
- Horloge Lucien Picard
- Horloge Luminox
- Horloge Maurice Lacroix
- Horloge Nautica
- Horloge Obaku
- Horloge Philip Watch
- Horloge Pilgrim
- Horloge Puma
- Horloge Shinola
- Horloge Skagen
- Horloge So & Co
- Horloge Tikkers
- Horloge Timberland
- Horloge TMI
- Horloge Triwa
- Horloge Tudor
- Horloge Versace
- Horloge WoodWatch
- Horloge Leff
- Horloge ETT
- Horloge Emporio Armani
- Horloge La Crosse Technology
- Horloge Spin Master
- Horloge Raketa
- Horloge Balmain
- Horloge Audemars Piguet
- Horloge Wonky Monkey
- Horloge Iron Annie
- Horloge Julie Julsen
- Horloge KRAEK
- Horloge X-WATCH
- Horloge PAUL HEWITT
- Horloge MICHELE
- Horloge Radley London
- Horloge PANERAI
- Horloge Zeppelin
- Horloge Hype
- Horloge Grand Seiko
Nieuwste handleidingen voor Horloge
14 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024