Cisco C1101-4PLTEP Handleiding

Cisco Router C1101-4PLTEP

Lees hieronder de 📖 handleiding in het Nederlandse voor Cisco C1101-4PLTEP (78 pagina's) in de categorie Router. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/78

Hardware Installation Guide for the Cisco 1000 Series Integrated

Services Router

Last Modified: 2019-06-07

Last Modified: 2020-02-11

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are

encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com

go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any

other company. (1721R)

C O N T E N T S

Overview of Cisco 1000 Series Integrated Services Routers 1

C H A P T E R 1

About Cisco 1000 Series Integrated Service Routers 1

Chassis Views 4

LED Indicators 12

Reset Button 19

Power Supply 19

Slots and Interfaces 20

About Slots, Subslots, and Port Numbering 20

Specifications of Cisco 1100 Series Integrated Services Routers 20

Periodic Inspection and Cleaning 20

Prepare for Router Installation 21

C H A P T E R 2

Safety Recommendations 21

Safety With Electricity 22

Prevent Electrostatic Discharge Damage 22

General Site Requirements 22

Site Selection Guidelines 23

Rack Requirements 23

Router Environmental Requirements 24

Power Guidelines and Requirements 25

Network Cabling Specifications 25

Console Port Connections 25

EIA/TIA-232 25

USB Serial Console 26

Console Port Considerations 27

Preparing for Network Connections 27

Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router

iii

Product specificaties

Merk:	Cisco
Categorie:	Router
Model:	C1101-4PLTEP
Kleur van het product:	Grijs
Breedte:	247.6 mm
Diepte:	167.6 mm
Hoogte:	43.9 mm
USB-poort:	Ja
Ethernet LAN:	Ja
Indicatielampje:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	4
WLAN gegevensoverdrachtsnelheid (max):	- Mbit/s
Interfacetype Ethernet LAN:	Gigabit Ethernet
Ethernet LAN, data-overdrachtsnelheden:	1000 Mbit/s
Bekabelingstechnologie:	10/100/1000Base-T(X)
Ondersteunde beveiligingsalgoritmen:	AES, WPA2
Antennas quantity:	2
Ethernet WAN:	Ja
Quality of Service (QoS):	Ja
AC-ingangsfrequentie:	50/60 Hz
Type product:	Router om neer te zetten
Code geharmoniseerd systeem (HS):	85176990
Antenne-ontwerp:	Extern