Chauvin Arnoux C.A 1550 Handleiding

Chauvin Arnoux Meetapparatuur C.A 1550

Lees hieronder de 📖 handleiding in het Nederlandse voor Chauvin Arnoux C.A 1550 (30 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/30

Micromanometer

EN - User’s manual

C.A 1550

WARNING, risk of DANGER! The operator must refer to these instructions whenever this danger symbol appears.

Information or useful tip.

Battery.

Magnet.

Earth.

Chauvin Arnoux has adopted an Eco-Design approach in order to design this appliance. Analysis of the complete life-

cycle has enabled us to control and optimize the e󰀨ects of the product on the environment. In particular this appliance

exceeds regulation requirements with respect to recycling and reuse.

The CE marking indicates compliance with the European Low Voltage Directive (2014/35/EU), Electromagnetic

Compatibility Directive (2014/30/EU) , Radio Equipment Directive (2014/53/EU), and Restriction of Hazardous

Substances Directive (RoHS, 2011/65/EU and 2015/863/EU).

The rubbish bin with a line through it indicates that, in the European Union, the product must undergo selective disposal

in compliance with Directive WEEE 2012/19/UE: This equipment must not be treated as household waste.

PRECAUTIONS OF USE

This instrument is compliant with safety standard IEC/EN 61010-2-030 or BS EN 61010-2-030, for voltages 5V with report to

ground. Failure to observe the safety instructions may result in electric shock, re, explosion, and destruction of the instrument

and of the installations.

The operator and/or the responsible authority must carefully read and clearly understand the various precautions to be taken in

use. Sound knowledge and a keen awareness of electrical hazards are essential when using this instrument.

Observe the conditions of use, namely the temperature, the relative humidity, the altitude, the degree of pollution, and the

place of use.

Do not use the instrument if it seems to be damaged, incomplete, or poorly close.

Before each use, check the condition of the housing. Any item of which the insulation is deteriorated (even partially) must be set

aside for repair or scrapping.

Do not make measurements on bare live conductors. Use a non-contact sensor or a sensor that provides the necessary electrical

insulation.

Always wear personal protective equipment (PPE), in particular insulating gloves, if there is any doubt or it is impossible to measure

the voltage levels to which the temperature sensor is connected.

All troubleshooting and metrological checks must be done by competent, accredited personnel.

Thank you for purchasing this CA 1550 micromanometer.

For best results from your instrument:

read these operating instructions carefully,

comply with the precautions for use.

CONTENTS

1. FIRST USE ............................................................................................................................................................................... 4

1.1. Delivery condition 4 ...........................................................................................................................................................

1.2. Accessories .................................................................................................................................................................... 4

1.3. Spare parts 4 .....................................................................................................................................................................

1.4. Inserting the batteries 5 .....................................................................................................................................................

2. PRESENTATION OF THE INSTRUMENT ............................................................................................................................. 6

2.1. C.A 1550 6 .........................................................................................................................................................................

2.2. Functions of the instrument 6 ............................................................................................................................................

2.3. Function keys 7 .................................................................................................................................................................

2.4. On/O󰀨 key ...................................................................................................................................................................... 8

2.5. Display 8 ............................................................................................................................................................................

3. USE IN STAND-ALONE MODE ............................................................................................................................................. 9

3.1. Temperature and pressure measurement 9 ......................................................................................................................

3.2. Air temperature and speed measurement 10 ....................................................................................................................

3.3. Temperature and air ow measurement ........................................................................................................................11

3.4. Temperature and atmospheric pressure measurement .................................................................................................11

3.5. Conguring the measurements .................................................................................................................................... 12

3.6. Other functions 13 .............................................................................................................................................................

3.7. Recording the measurements 15 ......................................................................................................................................

3.8. Errors 15 ............................................................................................................................................................................

4. USE IN RECORDING MODE ............................................................................................................................................... 16

4.1. Connection 16 ...................................................................................................................................................................

4.2. Obtain the Data Logger Transfer software 16 ...................................................................................................................

4.3. USB link 16 ........................................................................................................................................................................

4.4. Bluetooth link 17 ................................................................................................................................................................

4.5. Data Logger Transfer software 17 .....................................................................................................................................

4.6. CA Environmental Loggers application 20 .........................................................................................................................

5. TECHNICAL CHARACTERISTICS ..................................................................................................................................... 21

5.1. Reference conditions 21 ....................................................................................................................................................

5.2. Characteristics 21 ..............................................................................................................................................................

5.3. Variation in the domain of use 23 ......................................................................................................................................

5.4. Memory 24 .........................................................................................................................................................................

5.5. USB 24 ..............................................................................................................................................................................

5.6. Bluetooth 24 ......................................................................................................................................................................

5.7. Power supply 24 ................................................................................................................................................................

5.8. Environmental conditions 25 .............................................................................................................................................

5.9. Mechanical characteristics 25 ...........................................................................................................................................

5.10. Compliance with international standards 25 ....................................................................................................................

5.11. Electromagnetic compatibility (CEM) 25 ..........................................................................................................................

6. MAINTENANCE ..................................................................................................................................................................... 26

6.1. Cleaning 26 .......................................................................................................................................................................

6.2. Replacement of batteries 26 ..............................................................................................................................................

6.3. Updating the embedded software 26 .................................................................................................................................

7. WARRANTY ........................................................................................................................................................................... 28