CDA CI360 Handleiding

CDA Wasmachine CI360

Lees hieronder de 📖 handleiding in het Nederlandse voor CDA CI360 (26 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/26
QUICK START UP GUIDE
IMPORTANT
Instructions for drilling and mounting a door
Printed on Recycled Paper
F
C
A
G
E
E
C
C
H
C
B
D
DE
B
Drill holes in the wooden door following the instructions below
- Take the two hinges (A) and the tho protectors (B) out of the accessories bag.
- Put the protectors (B) underneath the hinges (A) and fix them to the front panel
of the machine with the screws (C) and then to the door with wood screws.
- Take the two magnet housings (D) and two protectors (B) out of the accessories bag.
- Put the protectors (B) underneath the magnet housings and fix then to the panel using the screws (C).
- Take a magnet (E) from the accessories bag, fix it to the top housing with
a screw (G) and fix the washer (F) to the door with a wood screw.
- Put the adhesive pad (H) in the bottom housing.
- Drill holes in the skirting panel and fix the two magnets (E).
If you don't mount the door, plug the holes with the
plugs supplied (8 pieces).
NB.: Provide a removable skirting board at the
base of the machine, at the front.
Filter removal and cleaning
To access the filter access remove the
skirting panel from the base of the
machine.
595
267,5
133,5383
576,5 min.
ÿ 35
TOP OF WASHING MACHINE
12
Cod. 3.77329.00 Ed. 0-09 -2007
1 - Detergent dispenser
2 - buttonOn/Off
3 - button Start
4 - buttonsReset
5 - Display
6 - buttonMode
7 - buttonSelect
8 - buttonsChild lock option
A)
In short, to start an automatic programme
•
•
•
•• Load your laundry in the drum and shut the
door.
•
•
•
•• Switch on the washing machine by pressing
On/Off button (2).
•
•
•
•• Put detergent and any necessary additives in
the relevant compartments.
•
•
•
•• Press Mode button (6) to select the desired
programme.
•
•
•
•• Press Select button (7) to confirm choice.
•
•
•
•• Press the Start button (3).
•
•
•
•• At the end of the programme, the machine
emits an acoustic signal (10 times) to warn
you, wait for the door icon to go off and then
take the laundry out of the drum.
•
•
•
•• Always switch the washing machine off at
the end of each wash, by pressing On/Off
button (2).
1) Detergent dispenser
The detergent dispenser
has two trays.
1 - Washing powder tray.
Pour washing powder into
this tray (max 180 gr.)
2 - Softener tray.
Pour softener into this tray, in the
amount recommended on the bottle (max 80 ml.)
Having loaded the powder and softener (the latter
optional), close the dispenser, making sure it’s
perfectly shut.
WASHING MACHINE
CI360
Control panel
B)
In short, to start a manual programme
with options
•
•
•
•• Load your laundry in the drum and shut the
door.
•
•
•
•• Switch on the washing machine by pressing
On/Off button (2).
•
•
•
•• Put detergent and any necessary additives
in the relevant compartments.
•
•
•
•• Press Mode button (6) to select the desired
programme.
•
•
•
•• Press Select button (7) to confirm choice.
•
•
•
•• rPress Mode button (6) epeatedly till you find
the desired option.
•
•
•
•• Press Select button (7) to confirm choice.
Repeat steps 6 and 7 for all the options you
want. When setting “Spin, Temperature,
Delayed start and Drying time”, an extra
step is necessary.
•
•
•
•• Press Start button (3) to start the
programme.
•
•
•
•• At the end of the programme, the machine
emits an acoustic signal (10 times) to warn
you, wait for the door icon to go off and then
take the laundry out of the drum.
•
•
•
•• Always switch the washing machine off at
the end of each wash, by pressing On/Off
button (2).
NB.: before moving the appliance it is
important to eliminate any residual water by
following the filter cleaning instructions;
this will avoid functional problems.
Problem
E01 Irregular heating
E02 Irregular operation
of motor
E03 Irregular operation
during water supply
E04 Irregular operation
during water draining
E06 Electronics panel
E05 Drum door safety
anomaly
If code E05 flashes during the programme set, the causes may be:
door not shut properly or a failure of the door safety lock system.
If code E01 flashes at the end of the programme, there is a fault with the
heating function. NB. The wash programme finishes as normal.
Symptoms
If code E02 flashes during the set programme the reasons could be either a
motor failure or a motor control circuit fault or a laundry overload
of the machine if the washing machine has a full load.
NB. The wash programme finishes early after a drain phase.
If code E03 flashes during the set programme, the water supply is faulty.
NB. The wash programme finishes early after a drain phase.
If code E04 flashes during the set programme, there are problems
in the drain phase. NB. The wash programme finishes early after a drain phase.
If code E06 flashes during the programme set, there is a malfunction in the
electronics board. NB. The wash programme finishes early after a drain phase.
Intensive
Eco
Normal
Intensive
Eco
Normal
Hot Wash
Synthetic
/ Curtains
/ Silk
Sport
and shoes
Wool
Drain
Rinse
Softener
Spin
60°
40°
60°
60°
40°
60°
90°
40°
40°
40°
/
/
/
/
8,5
8,5
8,5
6
6
6
6
4
4
3
UTILITY
PROGRAMMES SPECIAL PROGRAMMES FULL LOAD EVERYDAY
Cycle icon
Programme
Max. spin
Max. temp.
Delay
Quick wash
Delicate wash
Acqua plus
Extra rinse
Rinse Hold
Max. load in kg
max
max
max
max
max
max
max
800
800
800
max
max
max
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
/
/
/
/
/
/
/
/
•
•
•
•
•
•
/
/
/
/
/
/
/
/
•
•
•
•
•
•
•
•
/
/
•
•
/
/
•
•
•
•
•
•
•
•
/
/
/
/
/
/
/
/
/
/
/
/
/
•
•
•
/
/
/
/
Programmes display
Option Function .... Commands
Options table
Spin
select.
Temp.
select.
Delayed
start
select.
Quick
wash
Delicate
wash
Acqua
plus
Extra
rinse
Rinse
Hold
Child
safety
option
regulates
spin speed
regulates the
temperature
delays the start
in 30 min steps
up to 18 h.
cuts certain
cycles by
around 30 min.
reduces wash
movement in
certain cycles
adds more
rinse water
adds an extra
rinse on top
of set number
stops cycle
leaving laundry
to soak
locks the
programme
settings
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm spin speed
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm temperature
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm delay time
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm option
press Mode/P to choose and
Select to confirm option
press and Mode/P Select
at the same time
1 2
1
3
54 862
7
Mo de/ PO n/O ff
St a r t Selec t
Chi ld
lo c k
Mode/POn/Off
Start Select
Child
lock

Product specificaties

Merk: CDA
Categorie: Wasmachine
Model: CI360

Heb je hulp nodig?

Als je hulp nodig hebt met CDA CI360 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasmachine CDA

CDA

CDA CI381 Handleiding

22 Juni 2023
CDA

CDA ci325 Handleiding

20 Juni 2023
CDA

CDA CI230WH Handleiding

15 Juni 2023
CDA

CDA CI981 Handleiding

14 Juni 2023
CDA

CDA CI230SI Handleiding

11 Juni 2023
CDA

CDA CI371 Handleiding

9 Juni 2023
CDA

CDA CI340 Handleiding

8 Juni 2023
CDA

CDA CI361 Handleiding

7 Juni 2023
CDA

CDA CI830SI Handleiding

6 Juni 2023
CDA

CDA CI350 Handleiding

6 Juni 2023

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

LG

LG WT17BPBK Handleiding

22 November 2024
Bosch

Bosch WAX32M10 Handleiding

22 November 2024
LG

LG F2WV308NEW3 Handleiding

22 November 2024
Bosch

Bosch WAU28S70 Handleiding

22 November 2024
Bosch

Bosch Serie 6 WAU28PH2ES Handleiding

22 November 2024
Bosch

Bosch WGA142X2TR Handleiding

22 November 2024
LG

LG WF-79X3 Handleiding

22 November 2024
Edesa

Edesa EWF-7400 X Handleiding

22 November 2024
Smeg

Smeg WN04SEA Handleiding

21 November 2024
Smeg

Smeg WHT814ASIT Handleiding

21 November 2024