Casio WVA-109HDE-7AVER Handleiding

Casio Horloge WVA-109HDE-7AVER

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio WVA-109HDE-7AVER (5 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Operation Guide COMBIWVGE1

MO0612-EA

About This Manual

•The operational procedures for Modules 2734, 2758, 3748, 3749, 4773, and 4774

are identical. All of the illustrations in this manual show Modules 2734 and 2758.

•Button operations are indicated using the letters shown in the illustration.

Modules 2734 and 2758 Modules 3748 and 3749 Modules 4773 and 4774

•Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode, press to illuminate the display.B

Timekeeping Mode Press C.

▲

World Time Mode

Alarm Mode Date Alert Mode

Time Recorder ModeStopwatch Mode

Hand Setting Mode

▲

Radio-controlled Timekeeping

This watch receives a time calibration signal and update

its time setting accordingly. The time calibration signal

includes both Standard Time and Daylight Saving Time

(summer time) data.

•This watch is designed to pick up the time calibration

signal transmitted from Rugby, England and the signal

from Mainflingen, Germany.

Current Time Setting

This watch automatically adjusts its digital time setting in

accordance with a time calibration signal. You can also

perform a manual procedure to set the time and date,

when necessary.

•The first thing you should do after purchasing this watch

is to set your Home City, which is the city where you will

normally use the watch. For more information, see “To

set your Home City” below.

Month – Day

Day of week

Minute hand

Hour hand

•When using the watch that is outside of the range of the transmitters in Rugby and

Mainflingen, you need to manually adjust the time as required. See “ ”Timekeeping

for information about manual settings.

•The analog time of this watch is synchronized with the digital time. Because of this,

the analog time setting is automatically adjusted whenever you change the digital

setting. See “Analog Timekeeping” for more information.

To set your Home City

1. In the Timekeeping Mode, hold down A until the

transmitter indicator (A/T MSF, , or

DCF) starts to

flash, which indicates the setting screen.

•If the displayed transmitter indicator shows something

other than A/T A/T, use to display D before

advancing to the next step.

2. Press C to display the city code setting screen.

3. Use (east) and (west) to select the city code youD B

want to use as your Home City.

City code

•The following are the city codes for major cities in the Western Europe time

zones.

LON: London

PAR BER and : Paris, Berlin, Milan, Rome, Amsterdam, Hamburg, Frankfurt,

Vienna, Barcelona, Madrid

4. Press A twice to exit the setting screen.

•The first press of A displays the 12/24-hour setting screen. Pressing again exitsA

the setting screen.

Important!

•Normally, your watch should show the correct time as soon as you select your Home

City code. If it does not, it should adjust automatically after the next auto receive

operation (in the middle of the night). You can also perform manual receive or you

can set the time manually.

•If you are in an area that does not use Daylight Saving Time (summer time), turn off

the DST setting.

•See Transmitters“ ” for details about the transmitter indicator.

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal:

auto receive and manual receive.

•Auto Receive

With auto receive, the watch automatically picks up the time calibration signal five

times a day at 0:00 a.m., 1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. For more

information, see About Auto Receive“ ”.

•Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a

button. For more information, see “To perform manual receive”.

Important!

•Position the watch as shown in the nearby illustration, with its 12 o clock side facing’

towards a window. Make sure there are no metal objects nearby.

Resin Band Metal Band

•The watch should not be on its side or facing the wrong way.

•Proper signal reception can be difficult or even impossible under the conditions listed

below.

•Signal reception is normally better at night than during the day.

•Time calibration signal reception takes from two to five minutes, but in some cases it

can take as long as 12 minutes. Take care that you do not perform any button

operations or move the watch during this time.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances or

office

equipment,

or a mobile

phone

Near a

construction

site, airport, or

other sources

of electrical

noise

Near high-

tension

power lines

Among or

behind

mountains

•At distances further than about 500 kilometers from a transmitter, signal reception

may not be possible during certain times of year or times of day. Radio interference

may also cause problems with reception.

•Even when the watch is within the reception range of the transmitter, signal

reception is impossible if the signal is blocked by mountains or other geological

formations between the watch and signal source.

•Signal reception is affected by weather, atmospheric conditions, and seasonal

changes.

Rugby

Mainflingen

1,500 kilometers

500 kilometers

•See the information under “Signal Receive Troubleshooting” if you experience

problems with time calibration signal reception.

Operation Guide COMBIWVGE1

About Auto Receive

When auto receive is turned on, the watch automatically starts to receive the time

calibration signal when the digital time in the Timekeeping Mode reaches 0:00 a.m.,

1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. each day (calibration times). The watch

will also perform an additional auto receive operation at 5:00 a.m. if none of regularly

scheduled auto receive operations are successful.

Note

•The auto receive operation is performed only if the watch is in the Timekeeping

Mode or World Time Mode when one of the calibration times is reached. It is not

performed if a calibration time is reached while an alarm is sounding, or while you

are configuring settings (while settings are flashing on the display).

•Auto receipt of the calibration signal is designed to be performed early in the

morning, while you sleep (provided that the Timekeeping Mode time is set correctly).

Before going to bed for the night, remove the watch from your wrist, and put it in a

location where it can easily receive the signal.

•When auto receive is turned on, the watch receives the calibration signal for two to

five minutes everyday when the digital time in the Timekeeping Mode reaches each

of the calibration times. Do not perform any button operation within five minutes

before or after any one of the calibration times. Doing so can interfere with correct

calibration.

•Remember that reception of the calibration signal depends on the time kept in the

digital display. The receive operation will be performed whenever the display shows

any one of the calibration times, regardless of whether or not the displayed time is

actually the correct time.

•When two, three, four, or five receptions are successful, the watch uses the data of

the last reception for calibration. When only one reception is successful, the watch

uses the data of the successful reception.

Weak Strong

(Level 1) (Level 4)

About the Receiving Indicator

The receiving indicator shows the strength of the calibration signal being received. For

best reception, be sure to keep the watch in a location where signal strength is

strongest.

•Even in an area where signal strength is strong, it takes about 10 seconds for signal

reception to stabilize enough for the receiving indicator to indicate signal strength.

•Use the receiving indicator as a guide for checking signal strength and for finding the

best location for the watch during signal receive operations.

Receiving indicator

•The Level 4 receiving indicator remains on the display in all modes following

reception of the time calibration signal and calibration of the watch’s time setting.

The Level 4 receiving indicator is not displayed if signal reception was unsuccessful

or after manual adjustment of the current time setting.

•The Level 4 receiving indicator is displayed only when the watch is able to

successfully receive both time and date data. It does not appear when only time data

is received.

•The Level 4 receiving indicator indicates that at least one of the calibration signal

receive operations was successful. Note, however, that the Level 4 receiving

indicator is cleared from the display at 3:00 a.m. each day.

To perform manual receive

1. Place the watch on a stable surface so its top (12

o’clock side) is facing towards a window.

•Note that signal reception is poor when the 12 o’clock

side of the watch is not facing towards a window.

2. In the Timekeeping Mode, hold down D for about two

seconds until the watch beeps.

Receiving indicator

3. Release D and the current time flashes to indicate that signal reception has

started.

•Time calibration signal reception takes from two to five minutes. Take care that you

do not perform any button operations or move the watch during this time.

•After signal reception is complete, the display of the watch changes to the Last

Signal screen.

Note

•To interrupt a receive operation and return to the Timekeeping Mode, press D.

•If the receive operation is unsuccessful, the message ERR appears on the display

for about one or two minutes. After that, the watch returns to the Timekeeping Mode.

•You can also change from the Last Signal or ERR screen to the normal

timekeeping screen by pressing D.

To turn auto receive on and off

1. In the Timekeeping Mode, hold down A until the

transmitter indicator starts to flash, which indicates the

setting screen.

2. Press C three times to move the flashing to the auto

receive on/off setting.

3. Press D to toggle auto receive on (ON) and off (OF).

•If the current Home City setting is a city code that

does not support signal receive, “ ”xx appears in

place of the on/off indicator. This means you cannot

turn auto receive on or off.

4. Press A twice to exit the setting screen.

On/off status

To display the digital time and Last Signal screen

•In the Timekeeping Mode, press to cycle through the digital time screens asA

shown below.

•In the Timekeeping Mode, press to display the Last Signal screen (indicated byD

GET). The Last Signal screen shows the date and time of the last successful time

calibration signal reception.

▲

Press D.

Seconds

Last Signal Screen

Receive date Receive time

Alternate at two-

second interval

Day of week

Hour : Minutes Seconds Month – Day

▲

Press .A

▲

Month – Day

▲

Signal Receive Troubleshooting

Check the following points whenever you experience problems with calibration signal

reception.

Problem

Cannot perform

manual receive.

Auto receive is

turned on, but

the Level 4

receiving

indicator does

not appear on

the display.

Time setting is

incorrect

following signal

reception.

Probable Cause

•

The watch is not in the Timekeeping Mode.

•Your current Home City is not one of the

following city codes:

BER LON, PAR , or .

•The transmitter setting is incorrect.

•You changed the time setting manually.

•The watch was not in the Timekeeping

or World Time Mode, or you performed

some button operation during the auto

receive operation.

•Even if receive is successful, the Level

4 receiving indicator disappears every

day at 3 am.

•Time data (hour, minutes, seconds)

only was received during the last

receive operation. The Level 4

receiving indicator appears only when

time data and date data (year, month,

day) are both received.

•If the time is one hour off, the DST

setting may be incorrect.

•The Home City code setting is not

correct for the area where you are

using the watch.

What you should do

•Enter the Timekeeping Mode

and try again.

•Select , asBER PAR , or LON

your Home City.

•Select the transmitter setting

appropriate for your current

location.

•Select the transmitter setting

appropriate for your current

location.

•Perform manual signal receive

or wait until the next auto

signal receive operation is

performed.

•Check to make sure the watch

is in a location where it can

receive the signal.

•Change the DST setting to

Auto DST.

•Select the correct Home City

code.

•For further information, see “ ”Important! under “ ”Time Calibration Signal Reception

and “ ”Radio-controlled Timekeeping Precautions .

World Time

The World Time shows the current time in 30 cities (29

time zones) around the world.

•If the current time shown for a city is wrong, check your

Home City time settings and make the necessary

changes.

•The watch will perform a signal receive operation even if

it is in the World Time Mode when a calibration time is

reached. If this happens, the World Time Mode time

settings will be adjusted in accordance with the

Timekeeping Mode’s Home City time.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

City Code

Current time in the

selected city code

To view the time in another city

While in the World Time Mode, press D to scroll through the city codes (time zones).

•For full information on city codes, see the “City Code Table”.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A to toggle Daylight Saving Time (DST

displayed) and Standard Time ( not displayed).DST

•Note that you cannot use the World Time Mode to

change the DST setting of the Home City code you

currently have selected in the Timekeeping Mode. See

“To change the Daylight Saving Time (summer time)

setting” for information about turning the Home City

code DST setting on and off.

DST indicator

•The DST indicator is on the display whenever you display a city code for which

Daylight Saving Time is turned on.

•Note that the DST/Standard Time setting affects only the currently displayed city

code. Other city codes are not affected.

Alarms

The Alarm Mode gives you a choice of four one-time

alarms and one snooze alarm. One of the one-time

alarms functions as a target alarm,“ ” which counts the time

remaining from the current Home City time to the target

alarm time.

Also use the Alarm Mode to turn the Hourly Time Signal

on and off.

•There are five alarms named AL1, , , AL2 AL3 TAL

(target alarm), and . You can configure as aSNZ SNZ

snooze alarm only. Alarms AL1, , AL2 AL3, and

TAL can be used as one-time alarms only.

•Alarm settings (and Hourly Time Signal settings) are

available in the Alarm Mode, which you enter by

pressing .C

Alarm time

(Hour : Minutes)

Alarm name

Hourly Time

Signal Screen

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

•This operation automatically turns on the alarm.

3. Use C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D B (+) and ( ) to change it.–

•When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. ( indicator).P

AL1 AL2 AL3

SIG SNZ TAL

Operation Guide COMBIWVGE1

5. Press A to exit the setting screen.

•With the target alarm (TAL), the time starts to countdown as soon as you set the

alarm time.

Countdown

(Hours : Minutes)

Target Alarm Screen

▲

2 seconds

Countdown

(Seconds)

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, or until you turn the alarm off.

The target alarm counts the time remaining from the current Home City time to the

target alarm time. Note that the target alarm repeats automatically each day, as long

as it is turned on. You need to turn off the target alarm to disable it.

•Pressing any button stops the alarm tone operation.

•Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the snooze alarm setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on and off.

•Turning on a one-time alarm (AL1, , ,AL2 AL3

TAL) displays the alarm on indicator on its Alarm

Mode screen. Turning on the snooze alarm (SNZ)

displays the alarm on indicator and snooze alarm

indicator on its Alarm Mode screen.

•In all modes, the alarm on indicator is shown for any

alarm that is currently turned on. When the snooze

alarm is on, the snooze alarm indicator is displayed in all

modes.

•The alarm on indicator flashes while the alarm is

sounding.

•The snooze alarm indicator flashes during the 5-minute

intervals between alarms.

Snooze alarm indicator

Alarm on indicator

Modules 3748 and 3749

Alarm on indicator

Snooze alarm indicator

Modules 2734, 2758,

4773, and 4774

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal (SIG).

2. Press A to toggle it on (the Hourly Time Signal on

indicator displayed) and off (the Hourly Time Signal on

indicator not displayed).

•The Hourly Time Signal on indicator is displayed in all

modes when the Hourly Time Signal is turned on.

Hourly time signal

on indicator

Modules 2734, 2758,

4773, and 4774

Hourly time signal

on indicator

Modules 3748 and 3749

Date Alert

Date Alert helps you to remember an important date. After you set an alert date

(month and day), a date alert indicator ( ) and the current date flash for 24 hours after!

the alert date arrives in the Timekeeping Mode. You can set up to five different date

alerts.

Alert date

(Month – Day)

Alert name

Current date

(Month – Day)

Date alert

indicator

Date Alert Mode Screen Timekeeping Mode Screen

(Current date does not flash if

digital time is displayed on the

Timekeeping Mode screen.)

To set the alert date

1. Use C to enter the Date Alert Mode.

2. Use D to scroll through the alert screens until the one

whose date you want to set is displayed.

3. After you select an alert, hold down A until the month setting of the alert date

starts to flash, which indicates the setting screen.

•This operation automatically turns on the alert.

4. Press C to move the flashing between the month and day settings.

5. While the month or day setting is flashing, use (D B (+) and –) to change it.

6. Press A to exit the setting screen.

DA1 DA2 DA3

DA5 DA4

To turn an alert on and off

1. In the Date Alert Mode, use D to select the screen for

the alert (DA1through DA5) whose alert type you

want to select.

2. Press A to toggle it on and off.

•Note that the month and day do not appear if the alert is

turned off.

Press .A

Alert On

Alert Off

▲

Time Recorder

The Time Recorder Mode lets you store up to 30 time

entries (month, day, hour, minutes) with the touch of a

button. One way you can use the Time Recorder Mode is

to record the start time and the end time of a particular

event.

•All of the operations in this section are performed in the

Time Recorder Mode, which you enter by pressing C.

To record a Time Recorder time

1. Use C to enter the Time Recorder Mode.

•This displays the Time Recorder standby screen.

Standby Screen

Current time

(Hour : Minutes)

2. Press D to record the current date and time (month, day, hour, minutes).

•The recorded time flashes for about two seconds and then assigned the next

available record number, in the range of T1 T30 through . Next the time recorder

standby screen appears.

•A new time is recorded each time you press while the standby screen is on theD

display.

•Records are assigned numbers sequentially from T1 T30 through .

•Storing a new time record when there are already 30 records stored in memory

automatically deletes record T1, shifts the remaining records upwards by 1, and

stores the new record as T30.

To recall Time Recorder times

1. In the Time Recorder Mode, press A to recall Time Recorder times.

•If there are no time recorder times currently in memory, the standby screen

remains on the display when you press A.

2. Use D to scroll through times stored in memory.

Alternate at two-second interval

Recorded time

(Hour : Minutes)

Time record number

•Each press of D scrolls through time records from higher numbered (newer)

records to lower numbered records.

•If you recorded a new Time Recorder time since you last entered the Time Recorder

Mode, the newest record appears first. If you have not recorded a new time, the

record you were viewing when you last exited the Time Recorder Mode appears first.

•Press A to return to the standby screen.

To delete all Time Recorder times

Enter the Time Recorder Mode. While holding down , press A D to delete all Time

Recorder times.

Recorded date (Month – Day)

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

•The display range of the stopwatch is 59 minutes, 59.99

seconds.

•The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

Seconds

1/100 second

Minutes

Start Stop

Elapsed Time

➤

Re-start Clear

D➤

Stop

D➤D➤A

Split Time

Start Split

➤

Split release Clear

A➤

Stop

A➤D➤A

Two Finishes

Start Split

➤

Stop Clear

A➤

Split release

D➤A➤A

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

To measure times with the stopwatch

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	WVA-109HDE-7AVER
Gewicht:	95.5 g
Stopwatch:	Ja
Waterbestendig diepte:	50 m
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Snooze functie:	Ja
Klokmodus:	12/24 uur
Horlogekast materiaal:	Roestvrijstaal
Band materiaal:	Roestvrijstaal
Levensduur batterij/accu:	2 jaar
Ondersteund aantal accu's/batterijen:	1
Radio signaal ontvanger:	DCF/MSF
Afmetingen (B x D x H):	44 x 13 x 53.8 mm
Type batterij:	CR1620