Casio WV-200E-1AVEF Handleiding

Casio Horloge WV-200E-1AVEF

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio WV-200E-1AVEF (5 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Operation Guide 3139

MA0807-EA

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Caution!

Your watch is shipped with its Auto Display feature (which continually changes the

contents of the digital display) turned on. Calibration signal reception is disabled while

Auto Display is turned on.

Press any button to turn off Auto Display and return to the Timekeeping Mode.

About This Manual

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need in order to perform operations in

each mode. Further details and technical information

can be found in the “Reference” section.

General Guide

• Press C to change from mode to mode.

• In any mode (except when a setting screen is on the display), press

B to illuminate the display.

Timekeeping Mode World Time Mode Countdown

Timer Mode

Alarm ModeStopwatch Mode

Press .

Radio-controlled Atomic Timekeeping

Day of week

Year

Home Time

(Hour : Minutes Seconds)

Month – Day

PM indicator DST

indicator

This watch receives a time calibration signal and updates

its time setting accordingly.

•

Supported time calibration signals: Germany (Mainﬂ ingen),

England (Anthorn), United States (Fort Collins), Japan.

• See the information under “Signal Reception

Troubleshooting” if you experience problems with time

calibration signal reception.

Current Time Setting

This watch adjusts its time setting automatically in

accordance with a time calibration signal. You can also

perform a manual procedure to set the time and date,

when necessary.

•

The ﬁ rst thing you should do after purchasing this

watch is to specify your Home City (the city where you

normally will use the watch). For more information,

see “To specify your Home City”.

• When using the watch outside the areas covered by the time signal transmitters, you

will have to adjust the current time setting manually as required. See Timekeeping “ ”

for more information about manual time settings.

• The U.S. time calibration signal can be picked up by the watch while in North

America. The term North America in this manual refers to the area that consists of “ ”

Canada, the continental United States, and Mexico.

To specify your Home City

City code 1. In the Timekeeping Mode, hold down A until the city

code starts to ﬂ ash, which indicates the setting screen.

2. Press D(east) and B(west) to select the city code you

want to use as your Home City.

• Time calibration signal reception is supported when

any one of the city codes shown in the table below is

selected as your Home City.

German/U.K. Signal Japan Signal U.S. Signal

City

Code City

Name City

Code City

Name City

Code City

Name City

Code City

Name City

Code City

Name

LIS ATH HKG HNLLisbon Athens Hong Kong Honolulu WinnipegYWG

LON MOW BJS ANC CHILondon Moscow Beijing Anchorage Chicago

MAD TPE YVR MIAMadrid Taipei Vancouver Miami

PAR SEL LAX YTOParis Seoul Los Angeles Toronto

ROM TYO YEA NYCRome Tokyo Edmonton New York

BER DEN YHZBerlin Denver Halifax

STO MEX YYTStockholm Mexico City St. Johns

3. Press A twice to exit the setting screen.

Important!

• Normally, your watch should show the correct time as soon as you select your Home

City code. If it does not, it should adjust automatically after the next auto receive

operation (in the middle of the night). You can also perform manual receive or you

can set the time manually.

• The watch will receive the time calibration signal automatically from the applicable

transmitter (in the middle of the night) and update its settings accordingly. For

information about the relationship between city codes and transmitters, see Home “

City Codes and Transmitters .”

• Under factory default settings, auto receive is turned off for all of the following city

codes: (Honolulu), (Anchorage), (Moscow), (Hong Kong), and HNL ANC MOW HKG

BJS (Beijing). For details about turning on auto receive for these city codes, see “To

turn auto receive on and off .”

• You can disable time signal reception, if you want. See To turn auto receive on and “

off for more information.”

• See the maps under for information about the “Approximate Reception Ranges”

reception ranges of the watch.

• If you are in an area that does not use Daylight Saving Time (summer time), turn off

the DST setting.

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal:

auto receive and manual receive.

• Auto Receive

With auto receive, the watch receives the time calibration signal automatically up to

six times a day. When any auto receive is successful, the remaining auto receive

operations are not performed. For more information, see About Auto Receive“ ”.

• Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a

button. For more information, see To perform manual receive .“ ”

Operation Guide 3139

Important!

• When getting ready to receive the time calibration signal, position the watch as

shown in the nearby illustration, with its 12 o clock side facing towards a window. ’

This watch is designed to receive a time calibration signal late at night. Because of

this, you should place the watch near a window as shown in the illustration when

you take it off at night. Make sure there are no metal objects nearby.

12 o’clock

• Make sure the watch is facing the right way.

• Proper signal reception can be difﬁ cult or even impossible under the conditions listed

below.

Inside a

vehicle

Near

household

appliances,

office

equipment,

or a mobile

phone

Near a

construction

site, airport,

or other

sources of

electrical

noise

Near

high-tension

power lines

Among or

behind

mountains

Inside or

among

buildings

• Signal reception normally is better at night than during the day.

• Time calibration signal reception takes from two to seven minutes, but in some

cases it can take as long as 14 minutes. Take care that you do not perform any

button operations or move the watch during this time.

•

The time calibration signal the watch will attempt to pick up depends on its current

Home City code setting as shown below. If you use the watch in Japan or Europe (each

of which has two different transmitter locations), it will try to receive the time calibration

signal from one of the transmitters in your current location. If it cannot receive the

signal, it will then try to receive the time calibration signal from the other transmitter

Home City Codes and Transmitters

Home City Code Transmitter Frequency

LIS, LON, MAD, PAR, ROM,

BER, STO, ATH, MOW*

Anthorn (England)

Mainﬂ ingen (Germany)

60.0 kHz

77.5 kHz

HKG*, BJS*, TPE, SEL, TYO Fukushima (Japan)

Fukuoka/Saga (Japan) 40.0 kHz

60.0 kHz

HNL*, ANC*, YVR, LAX, YEA,

DEN, MEX, YWG, CHI, MIA,

YTO, NYC, YHZ, YYT

Fort Collins, Colorado

(the United States) 60.0 kHz

* The areas covered by the , , , , and HNL ANC MOW HKG BJS city codes are quite

far from the time calibration signal transmitters, and so certain conditions may

cause problems with signal reception.

Approximate Reception Ranges

U.S. Signal

Japan Signal

Fort Collins

Fukushima

Fukuoka/Sa

600 miles

(1,000 kilometers)

2,000 miles

(3,000 kilometers)

Anthorn

Mainflingen

500 kilometers

1,500 kilometers

1,000 kilometers

U.K. signal

transmitter

approximate

reception range

as of April 2007

U.K. and German Signals

• Signal reception may not be possible at the distances noted below during certain

times of the year or day. Radio interference may also cause problems with reception.

Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

•

In April 2007, the U.K. signal transmitter was moved from Rugby to Anthorn, which

resulted in a slight shift in the approximate reception range of the signal. The shift is so

slight that there is virtually no change in the ability to receive the signal.

• Even when the watch is within the reception range of a transmitter, signal reception may

be impossible at times due to the effects of geographic contours, structures, weather,

the season of the year, the time of day, radio interference, etc. Note that the signal

becomes weaker at distances of approximately 500 kilometers from the transmitter,

which means that the inﬂ uence of the conditions listed above becomes even greater.

About Auto Receive

The watch receives the time calibration signal automatically up to six times a day. When

any auto receive is successful, the remaining auto receive operations are not performed.

The reception schedule (calibration times) depends on your currently selected Home

City, and whether standard time or Daylight Saving Time is selected for your Home City.

Your Home City Auto Receive Start Times

123456

HNL, ANC, YVR,

LAX, YEA, DEN,

MEX, YWG, CHI,

MIA, YTO, NYC,

YHZ, YYT

Standard Time

Daylight

Saving Time

Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

LIS, LON

Standard Time 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight

Daylight

Saving Time 2:00 am 3:00 am 4:00 am 5:00 am Midnight

1:00 am

MAD, PAR, ROM,

BER, STO

Standard Time 2:00 am 3:00 am 4:00 am 5:00 am Midnight

1:00 am

Daylight

Saving Time 3:00 am 4:00 am 5:00 am Midnight

1:00 am

2:00 am

ATH

Standard Time 3:00 am 4:00 am 5:00 am Midnight

1:00 am

2:00 am

Daylight

Saving Time 4:00 am 5:00 am Midnight

1:00 am

2:00 am

3:00 am

MOW

Standard Time 4:00 am 5:00 am Midnight

1:00 am

2:00 am

3:00 am

Daylight

Saving Time 5:00 am Midnight

1:00 am

2:00 am

3:00 am

4:00 am

HKG, BJS, TPE,

SEL, TYO Standard Time Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

* Next day

Note

•

When a calibration time is reached

the watch will receive the calibration signal

only if it is in either the Timekeeping Mode or World Time Mode

Reception is not

performed if a calibration time is reached while you are conﬁ guring settings

• Auto receive of the calibration signal is designed to be performed early in the

morning, while you sleep (provided that the Timekeeping Mode time is set correctly).

Before going to bed for the night, remove the watch from your wrist, and put it in a

location where it can receive the signal easily.

• The watch receives the calibration signal for two to seven minutes everyday when

the time in the Timekeeping Mode reaches each of the calibration times. Avoid

performing any button operation within seven minutes before or after any one of the

calibration times. Doing so can interfere with correct calibration.

• Remember that reception of the calibration signal depends on the current time in the

Timekeeping Mode. The receive operation will be performed whenever the display

shows any one of the calibration times, regardless of whether or not the displayed

time actually is the correct time.

• Calibration signal reception is disabled while a countdown timer operation is in

progress.

About the Receiving Indicator

The receiving indicator shows the strength of the calibration signal being received.

For best reception, be sure to keep the watch in a location where signal strength is

strongest.

Receivin

indicator

Weak

(Level 0)

Strong

(Level 3)

• Even in an area where signal strength is strong, it takes about 10 seconds for signal

reception to stabilize enough for the receiving indicator to indicate signal strength.

• Use the receiving indicator as a guide for checking signal strength and for ﬁ nding the

best location for the watch during signal receive operations.

•

Following reception of the time calibration signal and calibration of the watch s time ’

setting, the Level 3 receiving indicator will remain on the display in all modes. The

Level 3 receiving indicator will not be displayed if signal reception was unsuccessful

or after you adjust the current time setting manually

• The Level 3 receiving indicator is displayed only when the watch is able to receive

both time and date data successfully. It does not appear when only time data is

received.

• The Level 3 receiving indicator indicates that at least one of the auto calibration

signal receive operations was successful. Note, however, that the Level 3 receiving

indicator is cleared from the display when the ﬁ rst auto receive operation of the day

is performed.

To perform manual receive

Receivin

indicator

1. Place the watch on a stable surface so its top (12

o clock side) is facing towards a window.’

2. In the Timekeeping Mode, hold down D for about two

seconds until appears on the display.RC!

• Time calibration signal reception takes from two to

seven minutes, but in some cases it can take as long

as 14 minutes. Take care that you do not perform any

button operations or move the watch during this time.

• After signal reception is complete, the display of the

watch changes to the Last Signal screen.

Note

• To interrupt a receive operation and return to the Timekeeping Mode, press

• If the receive operation is unsuccessful, the message

ERR appears on the display

for about one or two minutes. After that, the watch returns to the Timekeeping Mode.

• You can also change from the Last Signal or

ERR screen to the normal timekeeping

screen by pressing

• Calibration signal reception is disabled while a countdown timer operation is in

progress.

Operation Guide 3139

To turn auto receive on and off

On/Off Status 1. In the Timekeeping Mode, press

D to display the Last

Signal screen.

2. Hold down A until the receiving indicator and current

auto receive setting ( or ) start to ﬂ ash.

This is the setting screen.

• Note that the setting screen will not appear if the

currently selected Home City is one that does not

support time calibration reception.

3. Press D to toggle auto receive on ( ) and off

( ).

4. Press A to exit the setting screen.

• For information about city codes that support signal receive, see To specify your “

Home City”.

To display the Last Signal screen

In the Timekeeping Mode, press

D to display the Last Signal screen (indicated by

GET). The Last Signal screen shows the date and time of the last successful time

calibration signal reception.

Day of week

Month – Day

Receive time

Receive date

Year

Current Time and Date Screen Last Signal Screen

Press .

Home Time

(Hour : Minutes Seconds)

PM indicator DST indicator

Signal Reception Troubleshooting

Check the following points whenever you experience problems with calibration signal

reception.

Problem Probable Cause What you should do

Cannot perform

manual receive.

• The watch is not in the Timekeeping Mode.

• Your current Home City is not one of the

following city codes:

HNL ANC YVR DEN, , , , , LAX YEA , MEX,

YWG YHZ, CHI MIA NYC, , , YTO , , YYT, LIS,

LON, MAD, PAR, ROM, BER STO, , ATH,

MOW HKG BJS, , , TPE SEL, , and TYO.

• The countdown timer is running.

•

Enter the Timekeeping Mode

and try again.

•

Select one of the cities to the

left as your Home City.

•

Stop the countdown timer

and try again.

Auto receive is

turned on, but the

Level 3 receiving

indicator does

not appear on the

display.

• You changed the time setting manually.

• The watch was not in the Timekeeping or

World Time Mode, or you performed some

button operation during the auto receive

operation.

•

Perform manual signal

receive or wait until the next

auto signal receive operation

is performed.

Auto receive is

turned on, but

the Level 3

receiving

indicator does

not appear on

the display.

• Even if receive is successful, the Level 3

receiving indicator disappears ever y day

when the ﬁ rst auto receive operation of the

day is perfor med.

• Time data (hour, minutes, seconds) only was

received during the last receive operation.

The Level 3 receiving indicator appears only

when time data and date data (year, month,

day) are both received.

• Perform manual signal

receive or wait until the next

auto signal receive operation

is performed.

• Check to make sure the

watch is in a location where

it can receive the signal.

Time setting is

incorrect

following signal

reception.

• If the time is one hour off, the DST setting

may be incorrect.

• The Home City code setting is not correct for

the area where you are using the watch.

• Change the DST setting to

Auto DST.

• Select the correct Home City

code.

• For further information, see Important! and Radio-controlled Atomic Timekeeping “ ” “

Precautions .”

Countdown Timer

Timekeeping Mode time

(Hour : Minutes Seconds)

Minutes Seconds

You can set the countdown timer within a range of one

to 60 minutes. An alarm sounds when the countdown

reaches zero.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

To set the countdown start time

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to ﬂ ash, which indicates the

setting screen.

• If the countdown start time is not displayed, use the procedure under “To use the

countdown timer to display it.”

2. While a setting is ﬂ ashing, use

D (+) and B ( ) to change it.–

3. Press A to exit the setting screen.

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached, the alarm sounds for 10 seconds or until

you stop it by pressing any button. The countdown time is reset automatically to its

starting value after the alarm stops.

• Press D while a countdown operation is in progress to pause it. Press

D again to

resume the countdown.

• To stop a countdown operation completely, ﬁ rst pause it (by pressing

D), and then

press A. This returns the countdown time to its starting value.

• Calibration signal reception is disabled while a countdown timer operation is in

progress.

World Time

City code

Current time in

selected city

Timekeepin

Mode time

UTC offset

The World Time Mode shows you the current time in 48

cities (29 time zones) around the world.

• If the current time shown for a city is wrong, check

your Home City time settings and make the necessary

changes.

• All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

To view the time in another city

While in the World Time Mode, press D to scroll

eastward through the city codes (time zones).

• For full information on city codes, see the City Code “

Table at the back of this manual.”

To toggle a city code time between Standard Time and Daylight Saving Time

DST indicator

1. In the World Time Mode, use

D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A to toggle Daylight Saving Time (DST

indicator displayed) and Standard Time (DST indicator

not displayed).

• The DST indicator will appear whenever you display a

city code for which Daylight Saving Time is turned on.

• Note that the DST/Standard Time setting affects only the

currently displayed city code. Other city codes are not

affected.

Stopwatch

Timekeeping Mode time

(Hour : Minutes Seconds)

Minutes

Seconds

1/100 second

The stopwatch lets you measure elapsed time, split times,

and two ﬁ nishes.

• The display range of the stopwatch is 59 minutes, 59.99

seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing

To measure times with the stopwatch

Elapsed Time

Split Time

Two Finishes

Stop Re-start Stop ClearStart

Start Split

(SPL displayed) Split release Stop Clear

Start Split Stop Split release Clear

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

Alarm

Timekeeping Mode time

(Hour : Minutes Seconds)

Alarm on indicator

Hourly time signal on

indicator

Alarm time

(Hour : Minutes)

After you set (and turn on) the daily alarm, the alarm tone

sounds when the alarm time is reached. You can also turn

on an Hourly Time Signal that causes the watch to beep

for about one second every hour on the hour.

• All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing

To set the alarm time

1. In the Alarm Mode, hold down A until the hour setting

of the alarm time starts to ﬂ ash, which indicates the

setting screen.

• This automatically turns on the alarm.

2. Press C to move the ﬂ ashing between the hour and

minute settings.

3. While a setting is ﬂ ashing, use

D (+) and B ( ) to change it.–

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. ( indicator).P

4. Press A to exit the setting screen.

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	WV-200E-1AVEF
Timer:	1/1min - 1h
Gewicht:	114 g
Stopwatch:	Ja
Waterbestendig diepte:	200 m
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Klokmodus:	12/24 uur
Horlogekast materiaal:	Roestvrijstaal
Band materiaal:	Roestvrijstaal
Glas type van horloge:	Mineraalglas
Levensduur batterij/accu:	3 jaar
Ondersteund aantal accu's/batterijen:	1
Radio signaal ontvanger:	DCF/MSF/WWVB/JJY
Afmetingen (B x D x H):	47.7 x 15.2 x 52.2 mm
Type batterij:	CR1620