Casio Pro Trek PRW-7000TN-8JR Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Casio Pro Trek PRW-7000TN-8JR (17 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/17
E-7
2. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To confi gure Home City and summer time settings” (page E-36) to confi gure your
Home City and daylight saving time settings.
Important!
• Proper time calibration signal reception and World Time Mode data depend on correct Home City,
time, and date settings in the Timekeeping Mode. Make sure you confi gure these settings correctly.
3. Set the current time.
• To set the time using a time calibration signal
See “To get ready for a receive operation” (page E-22).
• To set the time manually
See “Confi guring Current Time and Date Settings Manually” (page E-38).
The watch is now ready for use.
• For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic
Timekeeping” (page E-20).
E-6
Things to check before using the watch
1. Check the battery power level.
Hold down B (page E-2) for at least two seconds to enter the Timekeeping Mode and display the battery
power level.
NO YES
YES
NEXT
The battery power level will be indicated as
H or M on the left
side of the digital display.
Battery power
indicator
Does any one of the conditions below exist?
• L fl ashing on the digital display.
• “CHARGE” fl ashing on the display.
The watch is charged
suffi ciently.
For details about
charging, see
“Charging the Watch”
(page E-13).
Power is low. Charge the watch by placing it in a location
where it is exposed to light. For details, see “Charging the
Watch” (page E-13). Go to step 2.
• When L is fl ashing, the second hand will jump at two-second intervals.
• When CHARGE is fl ashing, all hands will move to and stop at 12 o’clock.
E-5
Note
• If you do not perform any operation for more than two minutes after pulling out the crown, the indicator
shown below will appear and crown operations will become disabled. If this happens, push the crown
back in and then pull it out again to re-enable crown operations.
• Pulling out the crown while the watch is in a mode that does not allow confi guration of any settings will
cause the indicator shown below to appear. If this happens, push the crown back in and lock it.
• The indicator shown below also appears when performing hand home position adjustment. See “Hand
Home Position Adjustment” (page E-41) for more information.
1 second
• You can use high-speed movement to perform the following operations: when changing a time and/or
date setting; when selecting a city; when performing magnetic declination angle calibration, altitude
calibration, barometric pressure calibration, or temperature calibration operations; when calibrating
high tide times; when setting a latitude and longitude; when confi guring timer settings, when setting an
alarm time
E-4
High-speed Movement
You can use either of the crown operations described below to move watch hands or indicators at high
speed.
HS1: Can be used to move both hands and display indicators.
HS2: Can be used when setting the hour and minute manually to move the hands at high speed.
To start HS1 high-speed movement
While the crown is pulled out, rotate it rapidly a number of turns away from you
(for forward movement) or towards you (for reverse movement).
To start HS2 high-speed movement
While HS1 high-speed forward movement is in progress, rotate the crown
rapidly again a number of turns away from you.
To stop high-speed movement
Rotate the crown in the direction that is opposite that of the current high-speed
movement or press any button.
E-3
Using the Crown
The crown of this watch is a screw in lock crown. Before using the crown,
you must fi rst rotate it towards you to loosen it. After performing crown
operations, be sure to press the crown in lightly as you screw it back in.
Important!
• To maintain water resistance and avoid impact damage to the crown,
be sure to screw it back in when you are not using it.
The illustrations below show the different crown operations.
Pull out Rotate Push in
Crown
Loosen
E-2
About This Manual
• Depending on the model of your watch, digital display text appears
either as dark fi gures on a light background, or light fi gures on a dark
background. All examples in this manual are shown using dark fi gures
on a light background.
• Button operations are indicated using the letters shown in the
illustration.
• Note that the product illustrations in this manual are intended for
reference only, and so the actual product may appear somewhat
different than depicted by an illustration.
* In the Timekeeping Mode, the small hand indicates tide conditions
(page E-91).
Second hand
Crown
Hour hand Minute hand
Small hand*
E-1
ENGLISH
Important!
• The watch’s Altimeter Mode calculates and displays relative altitude based on barometric pressure
readings produced by its pressure sensor. This means that readings taken at different times at the
same location may produce different altitude values due to changes in barometric pressure. Also note
that the value displayed by the watch may be different from the actual elevation and/or sea level
elevation indicated for the area where you are located.
• When using the watch’s altimeter while mountain climbing, be sure to perform regular calibration in
accordance with the local altitude (elevation) indications. For more information, see “To specify a
reference altitude value” (page E-63).
• Whenever you use the digital compass of this watch for serious trekking, mountain climbing, or other
activities, be sure always to take along another compass to confi rm readings. If the readings produced
by the digital compass of this watch are different from those of the other compass, perform fi gure 8
calibration or 3-point calibration of the digital compass to ensure more accurate readings.
• Direction readings and digital compass calibration will not be possible if the watch is in the vicinity of a
permanent magnet (magnetic accessory, etc.), metal objects, high-voltage wires, aerial wires, or
electrical household appliances (TV, computer, cellphone, etc.)
Congratulations upon your selection of this CASIO watch.
Applications
The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.
Measured values are then shown on the display. Such features make this watch useful when hiking,
mountain climbing, or when engaging in other such outdoor activities.
Warning !
• The measurement functions built into this watch are not intended for taking measurements that
require professional or industrial precision. Values produced by this watch should be considered
as reasonable representations only.
•
When engaging in mountain climbing or other activities in which losing your way can create a
dangerous or life-threatening situation, always use a second compass to confi rm direction readings.
• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss
suffered by you or any third party arising through the use of your watch or its malfunction.
E
MO1803-EF © 2016 CASIO COMPUTER CO., LTD.
Operation Guide 5480
E-15
Level Battery Power Indicator Function Status
3
(L)
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Auto and manual receive, illumination,
beeper, sensor operation, tide level
indication, some Tide/Moon Mode
functions, some Fishing Mode functions,
and some Sunrise/Sunset Mode functions
disabled.
Second hand jumps every two seconds.
4
(CHARGE)
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
All hands stopped at 12 o’clock.
All functions disabled.
5 – – –
All hands stopped at 12 o’clock.
All functions disabled and settings return
to their initial factory defaults.
• The fl ashing L indicator at Level 3 (L) tells you that battery power is very low, and that exposure to
bright light for charging is required as soon as possible.
• Once the battery reaches Level 2 (M) after falling to Level 5, reconfi gure the current time, date, and
other settings.
• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).
E-14
Important!
• Allowing the watch to become very hot can cause its liquid crystal display to go blank (totally black or
totally white, depending on the watch model). The appearance of the LCD should become normal
again when the watch returns to a lower temperature.
• Turn on the watch’s Power Saving function (page E-19) and keep it in an area normally exposed to bright
light when storing it for long periods. This helps to ensure that power does not run down.
• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is
blocked from exposure to light can cause power to run down. Expose the watch to bright light
whenever possible.
Power Levels
Hold down B for at least two seconds to enter the Timekeeping Mode.
You can get an idea of the watch’s power level by observing the battery power indicator on the display.
Level Battery Power Indicator Function Status
1
(H) All functions enabled.
2
(M) All functions enabled.
Battery power
indicator
E-13
Charging the Watch
The face of the watch is a solar panel that generates power from light. The generated power charges a
built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed
to light.
Charging Guide
Whenever you are not wearing the
watch, leave it in a location where it
is exposed to light.
• Best charging performance is
achieved by exposing the watch to
the strongest light available.
When wearing the watch, make sure
that its face is not blocked from light
by the sleeve of your clothing.
• The watch may enter a sleep state
(page E-19) if its face is blocked by
your sleeve even only partially.
Warning!
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become particularly hot
when exposed to the conditions below for long periods.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
E-12
Checking the Current Time in a Different Time Zone ………………………………………………… E-112
To enter the World Time Mode …………………………………………………………………… E-112
To confi gure World Time City and summer time settings ……………………………………… E-113
To swap your Home City and World Time City …………………………………………………… E-115
To access the UTC (Universal Time Coordinated) time zone ………………………………… E-115
Illumination ………………………………………………………………………………………………… E-116
To turn on illumination manually …………………………………………………………………… E-116
To change the illumination duration ……………………………………………………………… E-116
To enable or disable the auto light switch ………………………………………………………… E-118
Other Settings ……………………………………………………………………………………………… E-120
To enable or disable the button operation tone ………………………………………………… E-120
To enable or disable Power Saving ……………………………………………………………… E-120
Troubleshooting …………………………………………………………………………………………… E-121
Specifi cations ……………………………………………………………………………………………… E-129
E-11
Looking up Sunrise and Sunset Times ………………………………………………………………… E-102
To enter the Sunrise/Sunset Mode ………………………………………………………………… E-102
To view the sunrise/sunset time for a particular date …………………………………………… E-103
To look up the sunrise and sunset times for a specifi c location ………………………………… E-103
Using the Stopwatch ……………………………………………………………………………………… E-105
To enter the Stopwatch Mode ……………………………………………………………………… E-105
To perform an elapsed time operation …………………………………………………………… E-105
To pause at a split time ……………………………………………………………………………… E-105
To measure two fi nishes …………………………………………………………………………… E-106
Using the Countdown Timer ……………………………………………………………………………… E-107
To enter the Countdown Timer Mode ……………………………………………………………… E-107
To specify the countdown start time ……………………………………………………………… E-107
To perform a countdown timer operation ………………………………………………………… E-108
To stop the alarm …………………………………………………………………………………… E-108
Using the Alarm …………………………………………………………………………………………… E-109
To enter the Alarm Mode …………………………………………………………………………… E-109
To set an alarm time ………………………………………………………………………………… E-110
To turn an alarm and the Hourly Time Signal on and off………………………………………… E-111
To stop the alarm tone ……………………………………………………………………………… E-111
To test the alarm tone ……………………………………………………………………………… E-111
E-10
Taking Barometric Pressure Readings ………………………………………………………………… E-75
To take barometric pressure readings …………………………………………………………… E-75
To specify the barometric pressure auto measurement interval ……………………………… E-78
To enable barometric pressure differential indication by the small hand ……………………… E-78
To enable or disable the barometric pressure change indicator ……………………………… E-81
To calibrate the pressure sensor …………………………………………………………………… E-83
Taking Temperature Readings …………………………………………………………………………… E-84
To take temperature readings ……………………………………………………………………… E-84
To calibrate the temperature sensor ……………………………………………………………… E-85
Viewing Altitude Records ………………………………………………………………………………… E-87
To view altitude records …………………………………………………………………………… E-87
To delete a specifi c record ………………………………………………………………………… E-90
To delete all recorded data ………………………………………………………………………… E-90
Checking the Tide Level and Moon Ages (Tide/Moon) ……………………………………………… E-91
To view the current tide level and Moon age……………………………………………………… E-91
To view the tide level and Moon age for a specifi c date and time ……………………………… E-93
To calibrate the high tide time ……………………………………………………………………… E-95
Viewing Favorable Fishing Times ……………………………………………………………………… E-97
To view today’s fi shing times ……………………………………………………………………… E-97
To display the fi shing time for a specifi ed date …………………………………………………… E-99
To turn the fi shing time alarm on or off …………………………………………………………… E-99
E-9
Moving the Hands for Easy Viewing of the Digital Display ………………………………………… E-42
To shift the hands and view digital info …………………………………………………………… E-42
To return the hands to their normal positions …………………………………………………… E-43
Taking Direction Readings ……………………………………………………………………………… E-44
To take a direction reading ………………………………………………………………………… E-45
To perform fi gure 8 calibration ……………………………………………………………………… E-48
To perform 3-point calibration ……………………………………………………………………… E-50
To perform magnetic declination correction ……………………………………………………… E-53
To store a direction angle reading in Bearing Memory ………………………………………… E-54
Specifying Altitude, Barometric Pressure, and Temperature Units ……………………………… E-58
To specify altitude, barometric pressure, and temperature units ……………………………… E-58
Using the Altimeter Mode ………………………………………………………………………………… E-59
To specify the altitude auto reading interval ……………………………………………………… E-60
To take altitude readings …………………………………………………………………………… E-61
To specify a reference altitude value ……………………………………………………………… E-63
To specify the altitude differential measurement range ………………………………………… E-65
To use the altitude differential value ……………………………………………………………… E-66
To save a reading manually ………………………………………………………………………… E-68
Precautions Concerning Simultaneous Altitude and Temperature Readings ………………… E-74
E-8
Contents
About This Manual …………………………………………………………………………………………… E-2
Using the Crown ……………………………………………………………………………………………… E-3
Things to check before using the watch ………………………………………………………………… E-6
Charging the Watch ………………………………………………………………………………………… E-13
To recover from the sleep state …………………………………………………………………… E-19
Radio Controlled Atomic Timekeeping ………………………………………………………………… E-20
To get ready for a receive operation ……………………………………………………………… E-22
To perform manual receive ………………………………………………………………………… E-24
To check the latest signal reception results ……………………………………………………… E-27
To turn auto receive on or off ……………………………………………………………………… E-28
Mode Reference Guide …………………………………………………………………………………… E-30
Timekeeping ………………………………………………………………………………………………… E-35
Confi guring Home City Settings ………………………………………………………………………… E-36
To confi gure Home City and summer time settings ……………………………………………… E-36
Confi guring Current Time and Date Settings Manually ……………………………………………… E-38
To change the current time and date settings manually ………………………………………… E-38
To switch between 12-hour and 24-hour timekeeping …………………………………………… E-40
Hand Home Position Adjustment ……………………………………………………………………… E-41
To trigger hand home position adjustment manually …………………………………………… E-41
Operation Guide 5480
E-23
• Signal reception may be diffi cult or even impossible under the conditions described below.
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
offi ce
equipment,
or a mobile
phone
Near a
construction
site, airport
Near
high-tension
power lines
Among or
behind
mountains
3. What you should do next depends on whether you are using auto receive or manual receive.
• Auto receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”
be low for details.
• Manual receive: Perform the operation under “To perform manual receive” on page E-24.
Auto Receive
• With auto receive, the watch performs the receive operation each day automatically up to six times (up
to fi ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to
the Timekeeping Mode time). When any receive operation is successful, none of the other receive
operations for that day are performed.
• When a calibration time is reached, the watch will perform the receive operation only if it is in the
Timekeeping Mode. The receive operation is not performed if a calibration time is reached while you
are confi guring settings.
E-22
• Even when the watch is within range of a transmitter, signal reception may be impossible due to the
effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,
etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the
infl uence of the conditions listed above becomes even greater.
• Signal reception may not be possible at the distances noted below during certain times of the year or
day. Radio interference may also cause problems with reception.
Mainfl ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 500 kilometers (310 miles)
• As of January 2016, China does not use Daylight Saving Time (DST). If China does go to the Daylight
Saving Time system in the future, some functions of this watch may no longer operate correctly.
To get ready for a receive operation
1. Confi rm that the watch is in the Timekeeping Mode. If it isn’t, use B to enter the Timekeeping Mode
(page E-32).
2. The antenna of this watch is located on its 7 o’clock side. Position the watch with 7 o’clock facing
towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.
• Signal reception normally is better at night.
• The receive operation takes from two to ten minutes, but
in some cases it can take as long as 20 minutes. Take
care that you do not perform any button operation or
move the watch during this time.
or
7 o’clock
E-21
Approximate Reception Ranges
UK and German Signals
Japanese Signals Chinese Signal
North American Signal
Anthorn
Mainfl ingen
Fukushima
500 kilometers
Fukuoka/Saga
1,000 kilometers
500 kilometers Changchun
Beijing
Shangqiu
Shanghai
Chengdu
Hong Kong
1,500 kilometers
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
Fort Collins
For the Honolulu and Anchorage time zones, the
signal can be received when reception conditions
are favorable.
500 kilometers
1,500 kilometers
The Anthorn signal is
receivable within this area
E-20
Radio Controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly. However, when
using the watch outside of areas covered by time calibration signals, you will have to adjust the settings
manually as required. See “Confi guring Current Time and Date Settings Manually” (page E-38) for more
information.
This section explains how the watch updates its time settings automatically when the city code selected
as the Home City is in Japan, North America, Europe, or China, and is one that supports time calibration
signal reception.
If your Home City Code setting is this: The watch can receive the signal from the transmitter
located here:
LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW Anthorn (England), Mainfl ingen (Germany)
HKG, BJS Shangqiu (China)
TPE, SEL, TYO Fukushima (Japan), Fukuoka/Saga (Japan)
HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ,
YYT Fort Collins, Colorado (United States)
Important!
• The areas covered by MOW, HNL and ANC are quite far from the calibration signal transmitters, so
certain conditions may cause reception problems.
• When
HKG or BJS is selected as the Home City, only the time and date are adjusted according to the
time calibration signal. You need to switch manually between standard time and daylight saving time
(DST) if required. See “To confi gure Home City and summer time settings” (page E-36) for information
about how to do this.
E-19
Power Saving
When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain
period in an area where it is dark. The table below shows how watch functions are affected by Power
Saving.
• For information about enabling and disabling power saving, see “To enable or disable Power Saving”
(page E-120).
• There actually are two sleep state levels: “display sleep” and “function sleep”.
Elapsed Time in Dark Hands and Display Operation
60 to 70 minutes (display sleep) Blank display, second hand
stopped.
Except for display and second hand, all
functions enabled.
6 or 7 days (function sleep) Blank display, all hands
stopped at 12 o’clock.
Except for timekeeping, all functions
disabled.
• The watch will not enter a sleep state between 6:00 a.m. and 9:59 p.m.. If the watch is already in a
sleep state when 6:00 a.m. arrives, however, it will remain in the sleep state.
• The watch will not enter a sleep state while it is in the Stopwatch Mode or Countdown Timer Mode.
• The watch will not enter a sleep state while barometric pressure change indicator is enabled (page E-80).
To recover from the sleep state
Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page
E-117).
E-18
Charging Times
Exposure Level (Brightness)
Daily
Operation
*1
Level Change *2
Level 5 Level 4 Level 3 Level 2 Level 1
Outdoor sunlight (50,000 lux) 8 min. 2 hours 21 hours 6 hours
Sunlight through a window (10,000 lux)
30 min. 6 hours 79 hours 22 hours
Daylight through a window on a
cloudy day (5,000 lux) 48 min. 10 hours 128 hours 35 hours
Indoor fl uorescent lighting (500 lux) 8 hours 113 hours – – – – – –
*1 Approximate amount of exposure time required each day to generate enough power for normal daily
operation.
*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.
• The above exposure times all are for reference only. Actual exposure times depend on lighting
conditions.
• For details about the operating time and daily operating conditions, see the “Power Supply” section of
the Specifi cations (page E-132).
E-17
Power Recovery Mode
• Performing multiple sensor, illumination, or beeper operations during a short period may cause the
recovery indicator (RECOVER) to start fl ashing on the display. This indicates that the watch is in the
power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and sensor
operations will be disabled until battery power recovers.
• Battery power will recover in about 15 minutes. At this time, the recovery indicator (
RECOVER) will stop
fl ashing. This indicates that the functions listed above are enabled again.
• Frequent fl ashing of the recovery indicator (RECOVER) indicates that battery power is low. Expose the
watch to bright light as soon as possible.
• Even if battery power is at Level 1 (
H) or Level 2 (M), the Digital Compass Mode, Barometer Mode,
Thermometer Mode or Altimeter Mode sensor may be disabled if there is not enough power available
to power it suffi ciently. This is indicated when the recovery indicator (
RECOVER) is fl ashing.
• Frequent fl ashing of the recovery indicator (RECOVER) probably means that remaining battery power
is low. Leave the watch in bright light to allow it to charge.
E-16
• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the
battery power indicator to show a reading temporarily that is higher than the actual battery level. The
correct battery level should be indicated after a few minutes.
• All data stored in memory is deleted, and the current time and all other settings return to their initial
factory defaults whenever battery power drops to Level 5 and when you have the battery replaced.
A dark environment while battery power is at Level 4 will cause the level to drop to Level 5. Expose the
watch to bright light whenever possible.
Low battery alert
When battery power reaches Level 3, the second hand of the watch will
jump at 2-second intervals in the Timekeeping Mode to let you know that
charging is required.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
ll
l
l
l
l
l
Jumps at two-second
intervals
Operation Guide 5480
Product specificaties
| Merk: | Casio |
| Categorie: | Horloge |
| Model: | Pro Trek PRW-7000TN-8JR |
Heb je hulp nodig?
Als je hulp nodig hebt met Casio Pro Trek PRW-7000TN-8JR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Horloge Casio
28 Oktober 2024
20 September 2024
20 Augustus 2024
6 Augustus 2024
21 Juli 2024
21 Juli 2024
21 Juli 2024
20 Juni 2024
24 Mei 2024
23 Mei 2024
Handleiding Horloge
- Horloge Braun
- Horloge IKEA
- Horloge Epson
- Horloge Huawei
- Horloge Garmin
- Horloge Medion
- Horloge Topcom
- Horloge Ade
- Horloge Adidas
- Horloge Alessi
- Horloge Alpina
- Horloge Armani
- Horloge Ascot
- Horloge Asics
- Horloge Auriol
- Horloge Beper
- Horloge BML
- Horloge Boss
- Horloge Bruno Sohnle
- Horloge Bulova
- Horloge Bushnell
- Horloge Dakota
- Horloge Danish Design
- Horloge Davis
- Horloge Detomaso
- Horloge Diesel
- Horloge Digi-tech
- Horloge Easypix
- Horloge Ebel
- Horloge Edox
- Horloge ELYSEE
- Horloge ESQ
- Horloge ETA
- Horloge Eurochron
- Horloge Ferrari
- Horloge Festina
- Horloge Fila
- Horloge Fitbit
- Horloge Fossil
- Horloge Freestyle
- Horloge GC Watches
- Horloge Geemarc
- Horloge Guess
- Horloge Habitat
- Horloge Haffstreuner
- Horloge Hamilton
- Horloge Hugo Boss
- Horloge ICE Watch
- Horloge Inter-Quartz
- Horloge Invicta
- Horloge Irox
- Horloge Kalenji
- Horloge Karlsson
- Horloge Kogan
- Horloge Krontaler
- Horloge La Crosse
- Horloge Lacoste
- Horloge Lambretta
- Horloge Longines
- Horloge Lorus
- Horloge Lotus
- Horloge Lynx
- Horloge Marc Jacobs
- Horloge Marquant
- Horloge Meister Anker
- Horloge Michael Kors
- Horloge Misfit
- Horloge Mitsubishi
- Horloge Mondaine
- Horloge Movado
- Horloge Naitica
- Horloge Naviforce
- Horloge Nedis
- Horloge Nike
- Horloge Polar
- Horloge Pulsar
- Horloge Pyle
- Horloge QQ
- Horloge Rado
- Horloge Renkforce
- Horloge Rodania
- Horloge Rolex
- Horloge Ronda
- Horloge Seiko
- Horloge Sempre
- Horloge Sinn
- Horloge Skmei
- Horloge Slazenger
- Horloge Speedo
- Horloge Spinnaker
- Horloge Stuhrling
- Horloge Suunto
- Horloge Swatch
- Horloge Tauchmeister
- Horloge TCM
- Horloge Technaxx
- Horloge Ticwatch
- Horloge Timer
- Horloge TimeStyle
- Horloge Timex
- Horloge Tissot
- Horloge Tommy Hilfiger
- Horloge TomTom
- Horloge Torgoen
- Horloge TW Steel
- Horloge Uri Minkoff
- Horloge Velleman
- Horloge Westfalia
- Horloge World Timer Chronograph
- Horloge Xonix
- Horloge Jaguar
- Horloge Junghans
- Horloge Just
- Horloge Olivia Burton
- Horloge Omega
- Horloge Oregon Scientific
- Horloge Orient
- Horloge Clas Ohlson
- Horloge Crivit
- Horloge Zenith
- Horloge Citizen
- Horloge Prologue
- Horloge Swiza
- Horloge Victorinox
- Horloge Bering
- Horloge Breitling
- Horloge Breo
- Horloge Brera
- Horloge Calypso
- Horloge Certina
- Horloge Christiaan Van Der Klaauw
- Horloge Christopher Ward
- Horloge Cover
- Horloge Daniel Steiger
- Horloge DMC
- Horloge Dugena
- Horloge Executive
- Horloge Fromanteel
- Horloge Gant
- Horloge Gc
- Horloge Girard-Perregaux
- Horloge Holzkern
- Horloge Hublot
- Horloge HYT
- Horloge IWC
- Horloge Jacques Lemans
- Horloge Klaus Kobec
- Horloge Lars Larsen
- Horloge Lucien Picard
- Horloge Luminox
- Horloge Maurice Lacroix
- Horloge Nautica
- Horloge Obaku
- Horloge Philip Watch
- Horloge Pilgrim
- Horloge Puma
- Horloge Shinola
- Horloge Skagen
- Horloge So & Co
- Horloge Tikkers
- Horloge Timberland
- Horloge TMI
- Horloge Triwa
- Horloge Tudor
- Horloge Versace
- Horloge WoodWatch
- Horloge Leff
- Horloge ETT
- Horloge Emporio Armani
- Horloge La Crosse Technology
- Horloge Spin Master
- Horloge Raketa
- Horloge Balmain
- Horloge Audemars Piguet
- Horloge Wonky Monkey
- Horloge Iron Annie
- Horloge Julie Julsen
- Horloge KRAEK
- Horloge X-WATCH
- Horloge PAUL HEWITT
- Horloge MICHELE
- Horloge Radley London
- Horloge PANERAI
- Horloge Zeppelin
- Horloge Hype
- Horloge Grand Seiko
Nieuwste handleidingen voor Horloge
16 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
14 November 2024
14 November 2024