Casio PRG-300-1A2 Handleiding

Casio Sporthorloge PRG-300-1A2

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio PRG-300-1A2 (14 pagina's) in de categorie Sporthorloge. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/14

Congratulations upon your selection of this CASIO watch.

Applications

The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.

Measured values are then shown on the display. Such features make this watch useful when hiking,

mountain climbing, or when engaging in other such outdoor activities.

Warning !

• The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered

as reasonable representations only.

•

When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss

suffered by you or any third party arising through the use of this product or its malfunction.

E E-1

ENGLISH

Important!

• Your watch’s Altimeter Mode calculates relative altitude based on changes in barometric pressure

measurement by its pressure sensor. For more information, see pages E-51 and E-65.

• Immediately before embarking or otherwise taking altitude readings, be sure to specify a reference

altitude. If you don’t the readings produced by the watch probably will not be very accurate. For more

information, see “To specify a reference altitude value” (page E-56).

• To ensure correct direction readings by this watch, be sure to perform bidirectional calibration before

using it. The watch may produce incorrect direction readings if you do not perform bidirectional

calibration. For more information, see “To perform bidirectional calibration” (page E-30).

E-2

About This Manual

• Depending on the model of your watch, digital display text appears

either as dark ﬁ gures on a light background, or light ﬁ gures on a dark

background. All examples in this manual are shown using dark ﬁ gures

on a light background.

• Button operations are indicated using the letters shown in the

illustration.

• Note that the product illustrations in this manual are intended for

reference only, and so the actual product may appear somewhat

different than depicted by an illustration.

E-3

Things to check before using the watch

1. Check the battery power level.

Is “H” or “M” displayed for the battery power indicator (page E-11)?

Go to step 2.

Power is low. Charge the watch by placing it in a location

where it is exposed to light. For details, see “Charging the

Watch” (page E-9).

NO YES

YES

Does any one of the following conditions exist?

• Battery power indicator shows “ ” and “ ” is flashing on the L LOW

display.

• “CHG” is flashing on the display.

• The face is blank.

The watch is charged

sufficiently.

For details about

charging, see

“Charging the Watch”

(page E-9).

Battery power

indicator

E-4

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City and summer time settings” (page E-20) to conﬁ gure

your Home City and daylight saving time settings.

Important!

• World Time Mode and Sunrise/Sunset Mode data depend on correct Home City, time, and date settings

in the Timekeeping Mode. Make sure you conﬁ gure these settings correctly.

3. Set the current time.

See “Conﬁ guring Current Time and Date Settings” (page E-22).

The watch is now ready for use.

E-5

Contents

About This Manual …………………………………………………………………………………………… E-2

Things to check before using the watch ………………………………………………………………… E-3

Charging the Watch …………………………………………………………………………………………… E-9

To recover from the sleep state …………………………………………………………………… E-14

Mode Reference Guide …………………………………………………………………………………… E-15

Timekeeping ………………………………………………………………………………………………… E-19

Conﬁ guring Home City Settings ………………………………………………………………………… E-20

To conﬁ gure Home City and summer time settings ……………………………………………… E-20

Conﬁ guring Current Time and Date Settings ………………………………………………………… E-22

To change the current time and date settings …………………………………………………… E-22

Taking Direction Readings ……………………………………………………………………………… E-25

To take a direction reading ………………………………………………………………………… E-26

To perform bidirectional calibration ………………………………………………………………… E-30

To perform magnetic declination correction ……………………………………………………… E-31

To store a direction angle reading in Bearing Memory ………………………………………… E-32

To set a map and ﬁ nd your current location ……………………………………………………… E-34

To ﬁ nd the bearing to an objective ………………………………………………………………… E-35

To determine the direction angle to an objective on a map and head in that direction

(Bearing Memory)………………………………………………………………………………… E-36

E-6

Specifying Temperature, Barometric Pressure, and Altitude Display Units …………………… E-40

To specify temperature, barometric pressure, and altitude display units ……………………… E-40

Taking Barometric Pressure and Temperature Readings ………………………………………… E-42

To take barometric pressure and temperature readings ………………………………………… E-42

To enable or disable the barometric pressure change alert …………………………………… E-47

To calibrate the pressure sensor and the temperature sensor ………………………………… E-49

Using the Altimeter Mode ………………………………………………………………………………… E-51

To select the altitude screen format ……………………………………………………………… E-52

To select the altitude auto reading interval ……………………………………………………… E-53

To take altitude readings …………………………………………………………………………… E-55

To specify a reference altitude value ……………………………………………………………… E-56

To specify the altitude differential start point ……………………………………………………… E-57

To use the altitude differential value ……………………………………………………………… E-58

To save a reading manually ………………………………………………………………………… E-59

To start trek log value updating …………………………………………………………………… E-62

To stop trek log value updating …………………………………………………………………… E-62

Precautions Concerning Simultaneous Altitude and Temperature Readings ………………… E-67

Viewing Altitude Records ………………………………………………………………………………… E-68

To view altitude records …………………………………………………………………………… E-68

To delete all manually saved data ………………………………………………………………… E-73

To delete data in a speciﬁ c memory area ………………………………………………………… E-73

E-7

Looking up Sunrise and Sunset Times ………………………………………………………………… E-75

To enter the Sunrise/Sunset Mode ………………………………………………………………… E-75

To view the sunrise/sunset time for a particular date …………………………………………… E-76

To look up the sunrise and sunset times for a speciﬁ c location ………………………………… E-77

Using the Stopwatch ……………………………………………………………………………………… E-79

To enter the Stopwatch Mode ……………………………………………………………………… E-79

To perform an elapsed time operation …………………………………………………………… E-79

To pause at a split time ……………………………………………………………………………… E-79

To measure two ﬁ nishes …………………………………………………………………………… E-80

Using the Countdown Timer ……………………………………………………………………………… E-81

To enter the Countdown Timer Mode ……………………………………………………………… E-81

To specify the countdown start time ……………………………………………………………… E-81

To perform a countdown timer operation ………………………………………………………… E-82

To stop the alarm …………………………………………………………………………………… E-82

Using the Alarm …………………………………………………………………………………………… E-83

To enter the Alarm Mode …………………………………………………………………………… E-83

To set an alarm time ………………………………………………………………………………… E-84

To turn an alarm and the Hourly Time Signal on and off………………………………………… E-85

To stop the alarm …………………………………………………………………………………… E-86

Operation Guide 3443

E-8

Checking the Current Time in a Different Time Zone ………………………………………………… E-87

To enter the World Time Mode …………………………………………………………………… E-87

To view the time in another time zone …………………………………………………………… E-87

To specify standard time or daylight saving time (DST) for a city ……………………………… E-88

Illumination ………………………………………………………………………………………………… E-89

To turn on illumination manually …………………………………………………………………… E-89

To change the illumination duration ……………………………………………………………… E-89

To turn the auto light switch on and off …………………………………………………………… E-91

Other Settings ……………………………………………………………………………………………… E-93

To turn the button operation tone on and off ……………………………………………………… E-93

To turn Power Saving on or off …………………………………………………………………… E-94

Troubleshooting …………………………………………………………………………………………… E-95

Speciﬁ cations ……………………………………………………………………………………………… E-99

E-9

Charging the Watch

The face of the watch is a solar panel that generates power from light. The generated power charges a

built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed

to light.

Charging Guide

Whenever you are not wearing the

watch, leave it in a location where it

is exposed to light.

• Best charging performance is

achieved by exposing the watch to

the strongest light available.

When wearing the watch, make sure

that its face is not blocked from light

by the sleeve of your clothing.

• The watch may enter a sleep state

(page E-13) if its face is blocked

by your sleeve even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become particularly hot

when exposed to the following conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

E-10

Important!

• Allowing the watch to become very hot can cause its liquid crystal display to black out. The

appearance of the LCD should become normal again when the watch returns to a lower temperature.

• Turn on the watch’s Power Saving function (page E-13) and keep it in an area normally exposed to

bright light when storing it for long periods. This helps to ensure that power does not run down.

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is

blocked from exposure to light can cause power to run down. Expose the watch to bright light

whenever possible.

E-11

Power Levels

You can get an idea of the watch’s power level by observing the battery power indicator on the display.

Level Battery Power Indicator Function Status

(H) All functions enabled.

(M) All functions enabled.

(L)

Illumination, beeper, and sensor operation

disabled.

(CHG)

Except for the current time and the

CHG

(charge) indicator, all functions and display

indicators disabled.

5 – – – All functions disabled.

• The ﬂ ashing LOW indicator at Level 3 (L) tells you that battery power is very low, and that exposure to

bright light for charging is required as soon as possible.

• At Level 5, all functions are disabled and settings return to their initial factory defaults. Once the battery

reaches Level 2 (M) after falling to Level 5, reconﬁ gure the current time, date, and other settings.

Battery power

indicator

Battery power

indicator

E-12

• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the

battery power indicator to show a reading temporarily that is higher than the actual battery level. The

correct battery level should be indicated after a few minutes.

• All data stored in memory is deleted, and the current time and all other settings return to their initial

factory defaults whenever battery power drops to Level 5 and when you have the battery replaced.

Power Recovery Mode

• Performing multiple sensor, illumination, or beeper operations during a short period may cause all of

the battery power indicators (H,M, and L) to start ﬂ ashing on the display. This indicates that the watch

is in the power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and

sensor operations will be disabled until battery power recovers.

• Battery power will recover in about 15 minutes. At this time, the battery power indicators (

H,M,L) will

stop ﬂ ashing. This indicates that the functions listed above are enabled again.

• If all of the battery power indicators (H,M,L) are ﬂ ashing and the

CHG (charge) indicator also is

ﬂ ashing, it means the battery level is very low. Expose the watch to bright light as soon as possible.

• Even if battery power is at Level 1 (

H) or Level 2 (M), the Digital Compass Mode, Barometer/

Thermometer Mode, or Altimeter Mode sensor may be disabled if there is not enough voltage available

to power it sufﬁ ciently. This is indicated when all of the battery power indicators (

H,M,L) are ﬂ ashing.

• Frequent ﬂ ashing of all of the battery power indicators (

H,M,L) probably means that remaining battery

power is low. Leave the watch in bright light to allow it to charge.

E-13

Charging Times

Exposure Level (Brightness)

Daily

Operation

Level Change *2

Level 5 Level 4 Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 5 min. 2 hours 18 hours 5 hours

Sunlight through a window (10,000 lux)

24 min. 7 hours 88 hours 24 hours

Daylight through a window on a

cloudy day (5,000 lux) 48 min. 14 hours 179 hours 48 hours

Indoor ﬂ uorescent lighting (500 lux) 8 hours 221 hours – – – – – –

*1 Approximate amount of exposure time required each day to generate enough power for normal daily

operation.

*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.

• The above exposure times all are for reference only. Actual exposure times depend on lighting

conditions.

• For details about the operating time and daily operating conditions, see the “Power Supply” section of

the Speciﬁ cations (page E-102).

Power Saving

When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain

period in an area where it is dark. The table below shows how watch functions are affected by Power

Saving.

• For information about enabling and disabling power saving, see “To turn Power Saving on and off”

(page E-94).

• There actually are two sleep state levels: “display sleep” and “function sleep”.

E-14

Elapsed Time in Dark Display Operation

60 to 70 minutes (display sleep) Blank, with

PS ﬂ ashing Display is off, but all functions are enabled.

6 or 7 days (function sleep) Blank, with

PS not ﬂ ashing All functions are disabled, but timekeeping is

maintained.

• The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch is already in a sleep

state when 6:00 AM arrives, however, it will remain in the sleep state.

• The watch will not enter a sleep state while it is in the Stopwatch Mode or Countdown Timer Mode.

To recover from the sleep state

Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page

E-90).

E-15

Mode Reference Guide

Your watch has 10 “modes”. The mode you should select depends on what you want to do.

To do this: Enter this mode: See:

• View the current date in the Home City

• Conﬁ gure Home City and daylight saving time (DST) settings

• Conﬁ gure time and date settings

Timekeeping Mode E-19

Determine your current bearing or the direction from your current location

to a destination Digital Compass Mode E-25

• View the barometric pressure and temperature at your current location

• View a graph of barometric pressure readings

Barometer/Thermometer

Mode E-42

• View the altitude at your current location

• Determine the altitude differential between two locations (reference

point and current location)

• Record an altitude reading with the reading time and date

Altimeter Mode E-51

View the sunrise and sunset times for a speciﬁ c date Sunrise/Sunset Mode E-75

Recall records created in the Altimeter Mode Data Recall Mode E-68

Use the stopwatch to measure elapsed time Stopwatch Mode E-79

Use the countdown timer Countdown Timer Mode E-81

Set an alarm time Alarm Mode E-83

View the current time in one of 48 cities (31 time zones) around the globe World Time Mode E-87

Operation Guide 3443

E-16

Selecting a Mode

• The illustration below shows which buttons you need to press to navigate between modes.

• To return to the Timekeeping Mode from any other mode, hold down D for about two seconds.

Countdown

Timer Mode Alarm Mode

Stopwatch Mode

World Time

Mode

Timekeeping Mode

Sunrise/Sunset

Mode

Data Recall

Mode

Countdown

Timer Mode Alarm Mode

Stopwatch Mode

World Time

Mode

Timekeeping Mode

Sunrise/Sunset

Mode

Data Recall

Mode

E-17

• You can use buttons A,B, and C to enter a sensor mode directly from the Timekeeping Mode or

from another sensor mode. To enter a sensor mode from the Sunrise/Sunset, Data Recall, Alarm,

Stopwatch, Countdown Timer or World Time, ﬁ rst enter the Timekeeping Mode and then press the

applicable button.

Sensor Modes

Altimeter Mode

Barometer/

Thermometer ModeDigital Compass Mode

Sensor Modes

Altimeter Mode

Barometer/

Thermometer ModeDigital Compass Mode

E-18

General Functions (All Modes)

The functions and operations described in this section can be used in all of the modes.

Direct Timekeeping Mode Access

• To enter the Timekeeping Mode from any other mode, hold down

D for about two seconds.

Auto Return Features

• The watch will automatically return to the Timekeeping Mode if you do not perform any button operation

for a particular amount of time in each mode.

Mode Name Approximate Elapsed Time

Sunrise/Sunset, Data Recall, Alarm, Digital Compass 3 minutes

Altimeter 1 hour minimum

12 hours maximum

Barometer/Thermometer 1 hour

Setting screen (digital setting ﬂ ashing) 3 minutes

• If you leave a screen with ﬂ ashing digits on the display for two or three minutes without performing any

operation, the watch exits the setting screen automatically.

Initial Screens

When you enter the Data Recall, Alarm, World Time, or Digital Compass Mode, the data you were viewing

when you last exited the mode appears ﬁ rst.

Scrolling

The A and C buttons are used on the setting screen to scroll through data on the display. In most

cases, holding down these buttons during a scroll operation scrolls through the data at high speed.

E-19

Timekeeping

Use the Timekeeping Mode (TIME) to set and view the current time and date.

• Each press of E in the Timekeeping Mode will change screen contents as shown below.

Day of the Week/Date Screen Month/Day Screen Barometric Pressure

Graph Screen

Barometric pressure graph

Day of week

Seconds

Hour :

Minutes

Day

indicator

Month Day

E-20

Conﬁ guring Home City Settings

There are two Home City settings: actually selecting the Home City and selecting either standard time or

daylight saving time (DST).

To conﬁ gure Home City and summer time settings

1. In the Timekeeping Mode, hold down E for at least two seconds.

First, SET Hold will ﬂ ash on the display, and CITY will be displayed in

the upper display. After that, the currently selected city code and city

name will scroll across the upper display. Keep E depressed until the

scrolling starts.

• The watch will exit the setting mode automatically if you do not

perform any operation for about two or three minutes.

• For details about city codes, see the “City Code Table” at the back

of this manual.

2. Use A (East) and C (West) to scroll through the available city codes.

• Keep scrolling until the city code you want to select as your Home

City is displayed.

3. Press D to display the DST setting screen.

Press A to toggle the DST setting between Daylight Saving Time (

ON)

and standard time (

OFF ).

• Note that you cannot switch between standard time and daylight

saving time (DST) while UTC is selected as your Home City.

indicator

City code

Hour :

Minutes

DST indicator

Seconds

indicator

City code

Hour :

Minutes

DST indicator

Seconds

E-21

5. After all of the settings are the way you want, press E twice to exit the setting screen.

• Daylight Saving Time is turned on when the indicator is on the display.DST

Note

• After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate

the current time for other time zones based on the current time in your Home City.

* Coordinated Universal Time, the world-wide scientiﬁ c standard of timekeeping.

The reference point for UTC is Greenwich, England.

E-22

Conﬁ guring Current Time and Date Settings

You can use the procedure below to adjust the Timekeeping Mode time and date settings if they are off.

To change the current time and date settings

1. In the Timekeeping Mode, hold down E for at least two seconds.

First, SET Hold will ﬂ ash on the display, and CITY will be displayed in

the upper display. After that, the currently selected city code and city

name will scroll across the upper display. Keep E depressed until the

scrolling starts.

indicator

City code

Hour :

Minutes

indicator

City code

Hour :

Minutes

E-23

2. Press D to move the ﬂ ashing in the sequence shown below to select the other settings.

Thermometer/Barometer/

Altitude display unit

Power

Saving

Illumination

Duration

Button Operation

Tone Day Month

City Code DST 12/24-Hour

Format Seconds Hour Minutes Year

• The following steps explain how to conﬁ gure timekeeping settings only.

3. When the timekeeping setting you want to change is ﬂ ashing, use A and/or C to change it as

described below.

Screen To do this: Do this:

Change the city code Use

A (East) and C (West).

Toggle between Daylight Saving Time (

) and

Standard Time (

OFF). Press A.

Toggle between 12-hour (

12H) and 24-hour (24H)

timekeeping. Press A.

Reset the seconds to 00

(If the current seconds count is between 30 and 59,

one is added to the minute count).

Press A.

Change the hour or minutes

Use A (+) and C (–).

Change the year, month, or day

4. After all of the settings are the way you want, press E twice to exit the setting screen.

Operation Guide 3443

Product specificaties

Merk:	Casio
Categorie:	Sporthorloge
Model:	PRG-300-1A2
Kleur van het product:	Black,Blue
Timer:	Ja
Gewicht:	57 g
Bluetooth:	Nee
Touchscreen:	Nee
Electronisch kompas:	Ja
Waterdicht:	Ja
Stopwatch:	Ja
Waterbestendig diepte:	100 m
Wereldklok functie:	Ja
Agenda:	Ja
Klokmodus:	12/24 uur
Nauwkeurigheid:	15 sec/maand
Horlogekast materiaal:	Kunststof
Band materiaal:	Kunststof
Barometer:	Ja
Hoogtemeter:	Ja
Waterdicht tot:	100 m
Veiligheidsfunties:	Waterbestendig
Zonnekracht:	Ja
Wekker:	Ja
Ingebouwde afstandsmeter:	Ja
Aanbevolen activiteit:	Hardlopen
Backlight:	Ja
Geheugencapaciteit:	30 entries
Thermometer:	Ja
Afmetingen (B x D x H):	47 x 12.6 x 56 mm
Oplaadbare batterij:	Ja
Timerduur (maximum):	24 uur
Tijd/afstand waarschuwing:	Ja
Afstand meeteenheid:	Imperial,Metric
Borstband:	Nee