Casio GW-A1100-1A3ER Handleiding

Casio Horloge GW-A1100-1A3ER

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio GW-A1100-1A3ER (11 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/11

Operation Guide 5311

E-9

2. Check the Home City.

Use the procedure under “To conﬁ gure Home City settings” (page E-36) to conﬁ gure your

Home City.

Important!

x Proper time calibration signal reception depends on correct Home City, time, and

day settings in the Timekeeping Mode. Make sure you conﬁ gure these settings

correctly.

3. Set the current time.

x To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-25).

x To set the time manually

See “Conﬁ guring Current Time and Day Settings Manually” (page E-41).

The watch is now ready for use.

x For details about the watch’s radio controlled timekeeping feature, see “Radio

Controlled Atomic Timekeeping” (page E-20).

E-8

Things to check before using the watch

1. Hold down at least two seconds to enter the Timekeeping Mode, and C

then observe the movement of the

.Second Hand

Is the

moving smoothly at one-second intervals?Second Hand

Is the

moving at Second Hand

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged. For details

about charging, see “Charging the

Watch” (page E-14).

Power is low. Charge the watch by

placing it in a location where it is

exposed to light. For details, see

“Charging the Watch” (page E-14).

YES

E-7

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the

current high-speed movement or press any button.

Note

x If you do not perform any operation for more than two minutes after pulling out the

crown, crown operations will become disabled automatically. If this happens, push

the crown back in and then pull it out again to re-enable crown operations.

x You can use high-speed hand movement when conﬁ guring time settings in the

Timekeeping Mode, Alarm Mode, or Countdown Timer Mode.

x Button operations become disabled after you perform a crown operation. If this

happens, rotate the crown slightly. This should restore button operations.

E-6

High-speed Movement

When rotating the crown to move the hands of the watch, you can use the operations

described below to move the hands at high speed, either forward or back. There are

two high-speed levels: HS1 and HS2 (faster than HS1).

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly three turns away

from you (for forward movement) or towards you (for reverse

movement). High-speed movement will continue even if you

release the crown.

To start HS2 high-speed movement

While HS1 high-speed movement is in progress, again rotate

the crown rapidly three turns in the same direction as the

current HS1 movement (away from you for forward movement

or towards you for reverse movement).

E-5

4. Gently pull on the crown to make sure it is securely locked and does not come out.

To unlock the crown

Rotate the crown so the groove aligns with Mark 1.

To pull out, rotate, or push the crown in

Important!

x Before performing any of these operations, ﬁ rst unlock the crown.

The illustrations below show the different crown operations.

Pull out Rotate Push in

E-4

Using the Crown

This watch has a lock-type crown.

Important!

x You should normally have the crown locked during normal daily use. Leaving the crown

unlocked creates the risk of unintended operations or even damage due to impact.

To lock the crown

1. Push the crown back in (see “To pull out, rotate, or push the

crown in” below).

x Note that attempting to lock the crown when it is not pushed

in can cause unexpected watch operation.

2. Rotate the crown so any one of its three grooves is aligned

with Mark 1.

3. While pushing in on the crown (a), rotate it to the right (b) until

it stops, and align the groove with Mark 2.

Mark 1

Groove

Mark 2

E-3

About This Manual

Operations are performed using the watch’s crown, and

the three buttons indicated by the letters , and in A B C

this manual.

Hands and Indicators

z z

Hour Hand

x x

Second Hand

c c

Minute Hand

v v

Upper Dial Hand: Indicates a time, in 24-hour format,

depending on the current mode.

b b

Lower Dial Hand: Indicates the current mode.

n n

Day Indicator

This User’s Guide uses numbers shown above to identify

watch hands and indicator.



BB @

E-2

Warning!

x The measurement functions built into this watch are not intended for taking

measurements that require professional or industrial precision. Values produced

by this watch should be considered as reasonable representations only.

x To ensure correct direction readings by this watch, be sure to perform

bidirectional calibration before using it. The watch may produce incorrect

direction readings if you do not perform bidirectional calibration. For more

information, see “To perform bidirectional calibration” (page E-56).

x Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

x Note that the product illustrations in this manual are intended for reference only, and

so the actual product may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours. Because of this, the radio-controlled atomic timekeeping function will not

display the correct time for Newfoundland, Canada.

MA1303-EA

#!3)/#/-054%2#/,4$

Operation Guide 5311

E-19

Power Saving

Power Saving enters a sleep state (second hand sleep or function sleep) whenever

the watch is left for a certain period in an area where it is dark.

Elapsed Time in Dark Operation

60 to 70 minutes (second

hand sleep)

only stopped at 12 o’clock, all other functions Second Hand

enabled

6 or 7 days (function sleep) x All functions, including analog timekeeping, disabled

x Internal timekeeping maintained

x The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch is

already in a sleep state when 6:00 AM arrives, however, it will remain there.

x The watch will not enter a sleep state while it is in the Stopwatch Mode or

Countdown Timer Mode.

To recover from the sleep state

Move the watch to a well-lit area or press any button.

E-18

Charging Times

Exposure Level (Brightness) Daily

Operation *1

Level Change *2

Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 minutes 2 hours 27 hours

Window sunlight (10,000 lux) 30 minutes 6 hours 99 hours

Window sunlight on cloudy day

(5,000 lux) 48 minutes 10 hours 161 hours

Indoor ﬂ uorescent lighting

(500 lux) 8 hours 111 hours – – –

* 1 Approximate exposure each day to generate power for normal daily operation.

* 2 Approximate exposure to take power up one level.

x The above times are for reference only. Actual times depend on lighting conditions.

x For details about the operating time and daily operating conditions, see the “Power

Supply” section of the Speciﬁ cations (page E-97).

E-17

x When power drops to Level 3, all settings (including timekeeping) will be cleared.

Recharging the battery will reset all settings to their initial factory defaults.

x When the watch is at Level 3, exposing it to light for a while will cause the

Second

Hand to move to the position of second 57. This indicates that charging has started.

Power Recovery Mode

The watch is designed to go into a power recovery mode that stops hand operation

temporarily whenever power suddenly drops below a certain level due to continuous

signal reception or other operations over a short period. Note that all operations are

disabled while the watch is in the power recovery mode.

The hands will move to the correct positions and the watch will resume normal

operation after power recovers (in about 15 minutes). Putting the watch in a location

where it is exposed to light will help power to recover sooner.

E-16

Low Power

Low power conditions are indicated by the movement of

the

in the Timekeeping Mode.Second Hand

x If the

is moving normally at one-second Second Hand

intervals, power is at Level 1.

x If the

is moving at two-second intervals, Second Hand

power is at Level 2, which is quite low. Expose the watch

to light as soon as possible so it can charge.

Low Battery Alert (Hand Movement and Function

Status)

Level Hand Movement Function Status

1 Normal. All functions enabled

moves at Second Hand

two-second intervals.

Beeper and time

calibration signal

reception disabled.

stopped.Second Hand All functions disabled

Moves at two-second

intervals.



E-15

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become

particularly hot when exposed to the following conditions for long periods.

x On the dashboard of a car parked in direct sunlight

x Too close to an incandescent lamp

x Under direct sunlight

Important!

x Keep the watch in an area normally exposed to bright light when storing it for long

periods. This helps to ensure that power does not run down.

x Storing the watch for long periods in an area where there is no light or wearing it in

such a way that it is blocked from exposure to light can cause power to run down.

Make sure that the watch is exposed to bright light whenever possible.

Checking the Current Power Level

Certain functions will be disabled when the power level is low. If the power level is

low, leave the watch in a location where its face (solar panel) is exposed to light.

E-14

Charging the Watch

The face of the watch is a solar panel that generates power from light. The generated

power charges a built-in rechargeable battery, which powers watch operations. The

watch charges whenever it is exposed to light.

Charging Guide

Whenever you are not

wearing the watch, be sure

to leave it in a location

where it is exposed to light.

x Best charging

performance is achieved

by exposing the watch to

light that is as strong as

possible.

When wearing the watch,

makes sure that its face is

not blocked from light by

the sleeve of your clothing.

x The watch may enter a

sleep state (page E-19) if its

face is blocked by your

sleeve even only partially.

E-13

E-79 Adjusting Home Positions

E-81 To adjust home positions

E-83 Troubleshooting

E-95 Speciﬁ cations

E-12

E-63 Checking the Current Time in a Different Time Zone

E-64 To view the time in another time zone

E-67 To swap your Home City and World Time City

E-69 Using the Stopwatch

E-70 To enter and exit the Stopwatch Mode

E-70 To perform an elapsed time operation

E-70 To perform ﬂ yback timing

E-72 Using the Countdown Timer

E-73 To specify the countdown start time

E-74 To perform a countdown timer operation

E-74 To stop the alarm

E-75 Using the Alarm

E-76 To change the alarm time setting

E-78 To turn the alarm on or off

E-78 To stop the alarm

E-11

E-32 Mode Reference Guide

E-33 To determine the watch’s current mode

E-33 To return to the Timekeeping Mode from any other mode

E-34 To select a mode

E-35 Timekeeping

E-36 Conﬁ guring Home City Settings

E-36 To conﬁ gure Home City settings

E-39 To switch between standard time and summer time manually

E-41 Conﬁ guring Current Time and Day Settings Manually

E-41 To change the current time setting manually

E-44 To change the current day setting manually

E-48 Taking Direction Readings

E-50 To take a direction reading

E-56 To perform bidirectional calibration

E-58 To perform northerly calibration

E-10

Contents

E-3 About This Manual

E-4 Using the Crown

E-4 To lock the crown

E-5 To unlock the crown

E-5 To pull out, rotate, or push the crown in

E-8 Things to check before using the watch

E-14 Charging the Watch

E-19 To recover from the sleep state

E-20 Radio Controlled Atomic Timekeeping

E-25 To get ready for a receive operation

E-28 To perform manual receive

E-29 To check the result of the latest receive operation

E-30 To turn auto receive on and off

Operation Guide 5311

E-29

Note

x To interrupt a receive operation and return to the Timekeeping Mode, press any

button.

To check the result of the latest receive operation

In the Timekeeping Mode, press . The B

Second

Hand will move to ( ) or ( ) to indicate the last Y YES N NO

calibration signal receive result.

x The

will move to ( ) if the latest Second Hand Y YES

receive operation was successful, or ( ) if it was N NO

not. After about 10 seconds, regular timekeeping will

resume.

x Press to return to regular timekeeping. The watch will B

also return to regular timekeeping if you do not perform

any operation for about 10 seconds.



E-28

To perform manual receive

1. In the Timekeeping Mode (page E-35), keep B depressed (for about two seconds) as

the

goes through the following sequence.Second Hand

x Moves to ( ) or ( ) to indicate the last signal reception result, then to Y YES N NO

R (READY).

2. The

indicates the operations the watch is currently performing.Second Hand

When the x

is Second Hand

pointed here: It means this:

R (READY)

Watch is setting up for reception.

W (WORK) Reception is in progress.

x If signal reception is unstable, the x

may Second Hand

move between ( ) and ( ).W WORK R READY

x When the receive operation is successful, the watch

adjusts the time setting accordingly, and then resumes

regular timekeeping. It does not adjust the setting if the

operation failed.



E-27

3. What you should do next depends on whether you are using Auto Receive or

Manual Receive.

x Auto Receive: Leave the watch over night in the location you selected in step 2.

See “Auto Receive” on page E-27 for details.

x Manual Receive: Perform the operation under “To perform manual receive” on

page E-28.

Auto Receive

x With Auto Receive, the watch performs the receive operation each day

automatically up to six times (up to ﬁ ve times for the Chinese calibration signal)

between the hours of midnight and 5 a.m. (according to the Timekeeping Mode

time). When any receive operation is successful, none of the other receive

operations for that day are performed.

x When a calibration time is reached, the watch will perform the receive operation

only if it is in the Timekeeping Mode. The receive operation is not performed if a

calibration time is reached while you are conﬁ guring settings.

E-26

x Signal reception may be difﬁ cult or even impossible under the conditions

described below.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances,

ofﬁ ce

equipment,

or a mobile

phone

Near a

construction

site, airport,

or other

sources of

electrical

noise

Near

high-tension

power lines

Among

or behind

mountains

E-25

To get ready for a receive operation

1. Conﬁ rm that the watch is in the Timekeeping Mode. If it isn’t, hold down for at C

least two seconds to enter the Timekeeping Mode.

2. Place the watch in a location where signal reception is good.

12 o’clock

x Position the watch as shown in the

nearby illustration, with 12 o’clock

pointed towards a window. Make

sure there are no metal objects

nearby.

x Signal reception normally is better

at night.

x The receive operation takes from

two to 10 minutes, but in some

cases it can take as long as

20 minutes. Take care that you do

not perform any button operation or

move the watch during this time.

E-24

x Signal reception may not be possible at the distances noted below during certain

times of the year or day. Radio interference may also cause problems with reception.

− Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers

(310 miles)

− Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

− Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

− Shangqiu (China) transmitter: 500 kilometers (310 miles)

x As of December 2012, China does not use Daylight Saving Time (DST). If China

does go to the Daylight Saving Time system in the future, some functions of this

watch may no longer operate correctly.

x Using this watch in a country covered by a time calibration signal that is different

from the countries it supports may result in incorrect time indication due to local

application of daylight saving time (summer time), etc.

E-23

Japanese Signals Chinese Signal

Fukushima

500 kilometers

Fukuoka/Saga

1,000 kilometers 1,500 kilometers

Changchun500 kilometers

Beijing

Shangqiu

Shanghai

Chengdu

Hong Kong

E-22

Approximate Reception Ranges

UK and German Signals North American Signal

Anthorn

500 kilometers

1,500 kilometers

Mainﬂ ingen

The Anthorn signal is receivable

within this area.

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Fort Collins

E-21

If your Home City Code setting is this: The watch can receive the signal from

the transmitter located here:

LON (LONDON), PAR (PARIS), ATH (ATHENS) Anthorn (England), Mainﬂ ingen

(Germany)

HKG (HONG KONG) Shangqiu City (China)

TYO (TOKYO) Fukushima (Japan), Fukuoka/Saga

(Japan)

HNL (HONOLULU), ANC (ANCHORAGE),

LAX (LOS ANGELES), DEN (DENVER), CHI

(CHICAGO), NYC (NEW YORK)

Fort Collins, Colorado (United States)

Important!

x The areas covered by ( ) and ( ) are quite far HNL HONOLULU ANC ANCHORAGE

from the calibration signal transmitters, so certain conditions may cause reception

problems.

E-20

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

However, when using the watch outside of areas covered by time calibration signals,

you will have to adjust the settings manually as required. See “Conﬁ guring Current

Time and Day Settings Manually” (page E-41) for more information.

This section explains how the watch updates its time settings when the city code

selected as the Home City is in Japan, North America, Europe, or China, and is one

that supports time calibration signal reception.

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	GW-A1100-1A3ER
Gewicht:	93 g
Breedte:	53.8 mm
Diepte:	17.3 mm
Hoogte:	48.4 mm
LED backlight:	Ja
Type horloge:	Armbandhorloge
Mechanismetype:	Kwarts (zonne-energie)
Type wijzerplaat horloge:	Analoge wijzerplaat
Waterdicht:	Ja
Stopwatch:	Ja
Countdown timer:	Ja
Waterbestendig druk:	20 ATM
Waterbestendig diepte:	200 m
Schokbestendig:	Ja
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Type kalender:	Overdag
Kleur behuizing:	Zwart
Hoofdkleur van band:	Zwart
Glas type van horloge:	Saffier
Hoesvorm:	Rond
Hoofdkleur van wijzerplaat:	Zwart
Geslacht:	Man
Stijl becijfering horloge:	Arabische cijfers/geen cijfers
Radio signaal ontvanger:	EU, USA, Japan, China
Productontwerp:	Sport
Type batterij:	CTL1616