Casio G9000-1V Handleiding

Casio Horloge G9000-1V

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio G9000-1V (4 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Operation Guide 3031

To measure times with the stopwatch

(Stopwatch Mode (ST1) and Stopwatch Mode (ST2))

Elapsed Time

Start Stop Re-start Stop Clear

Start Split

( displayed)

Split release Stop Clear

Start Split Stop Split release Clear

Split Time

Two Finishes

First runner finishes.

Display time of first

runner.

Second runner

finishes.

Display time of

second runner.

About Auto-Start (Stopwatch Mode (ST1))

With Auto-Start, the watch performs a 5-second countdown, and stopwatch operation

starts automatically when the countdown reaches zero.

During the final three seconds of the countdown, a beeper sounds with each second.

To use Auto-Start (ST1)

1. While the stopwatch screen is showing all zeros in the

Stopwatch Mode, press B.

•This displays a 5-second countdown screen.

•To return to the all zeros screen, press B again.

2. Press D to start the countdown.

•When the countdown reaches zero, a tone sounds and

a stopwatch timing operation starts automatically.

•Pressing D while the Auto-Start countdown is in

progress starts the stopwatch immediately.

Stopwatches

Your watch has two stopwatch modes:Stopwatch Mode

(ST1) and Stopwatch Mode (ST2). Both stopwatch modes

let you measure elapsed time, split times, and two

finishes. The Stopwatch Mode (ST1) includes Auto-Start.

•A display range of the stopwatch is 999 hours,

59 minutes, 59.99 seconds.

•A stopwatch continues to run, restarting from zero after

it reaches its limit, until you stop it.

•A stopwatch measurement operation continues even if

you exit a Stopwatch Mode.

•Exiting a Stopwatch Mode while a split time is frozen on

the display clears the split time and returns to elapsed

time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode (ST1) or Stopwatch Mode (ST2),

which you enter by pressing C.

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press to toggle between 12-hour timekeeping and 24-D

hour timekeeping.

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

•The P indicator is not displayed when the current time is displayed in other modes.

MA0604-EA

About This Manual

•Depending on the model of your watch, display text

appears either as dark figures on a light background or

light figures on a dark background. All sample displays

in this manual are shown using dark figures on a light

background.

•Button operations are indicated using the letters shown

in the illustration.

•Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

Timekeeping Mode World Time ModeAlarm ModeCountdown Timer ModeStopwatch Mode (ST1) Stopwatch Mode (ST2)

Press .

General Guide

•Press C to change from mode to mode.

•In any mode, press L to illuminate the display.

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Seconds Home Time Zone Hour

Year MinutesDay

DST

Month

3. When the setting you want to change is flashing, use D and B to change it as

described below.

Home time zone

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

Read This Before You Set the Time and Date !

The times displayed in the Timekeeping Mode and World

Time Mode are linked. Because of this, make sure you

select a Home Time zone before you set the time and

date.

Day of week

Month – Day

Hour : Minutes

PM indicator

Seconds

DST indicator

Screen

OFF

6-30

To do this:

Reset the seconds to 00

Toggle between Daylight Saving

Time (ON) and Standard Time (

OFF)

Specify your Home Time zone

Change the hour or minutes

Change the year

Change the month or day

Do this:

Press .D

Use D (eastward) and B (westward).

Use ).D (+) and B (–

•

For details about time zones, see the

“

City Code Table

”

•See “Daylight Saving Time (DST) for details about DST setting.”

4. Press A to exit the setting screen.

•The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from Standard

Time. Remember that not all countries or even local areas use Daylight Saving Time.

To toggle the Timekeeping Mode time between DST and Standard Time

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to display the DST setting screen.

3. Press D to toggle between Daylight Saving Time

(ON displayed) and Standard Time (OFF displayed).

4. Press A to exit the setting screen.

•The DST indicator appears on the display to indicate

that Daylight Saving Time is turned on.

1/100 second

Minutes

Seconds

Timekeeping Mode time

*During stopwatch elapsed

time measurement,

shows the number of

hours elapsed.

Operation Guide 3031

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal (SIG).

2. Press A to toggle it on and off.

•The Hourly Time Signal on indicator ( ) is shown on

the display in all modes while this function is turned on.

5. Press A to exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off.

•Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

•Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the

SNZ

setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on and off.

•Turning on a alarm (SNZ, AL1, , AL2 AL3, or

AL4) displays the alarm on indicator ( , , , ,

or ).

•In all modes, the alarm on indicator is shown for alarm

that is currently turned on.

•The alarm on indicator flashes while the alarm is

sounding.

•The snooze alarm indicator ( ) flashes while the

snooze alarm is sounding and during the 5-minute intervals

between alarms.

Alarms

You can set up to five independent multi-function alarms

with hour, minutes, month, and day. When an alarm is

turned on, the alarm tone sounds when the alarm time is

reached. One of the alarms is a snooze alarm, while the

other four are one-time alarms.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

•There are five alarm screens numbered AL1, AL2,

AL3 AL4, and for the one-time alarm, a snooze

alarm screen indicated by SNZ. The Hourly Time

Signal screen is indicated by SIG.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

•To specify a countdown start time of 24 hours, set .

4. Press A to exit the setting screen.

•You can also perform steps 1 and 2 of the above procedure whenever you need to

view the current auto-repeat and progress beeper settings.

To use the countdown timer

Press while in the Countdown Timer Mode to start theD

countdown timer.

•The countdown timer operation continues even if you

exit the Countdown Timer Mode.

•Press D while a countdown operation is in progress to

pause it. Press again to resume the countdown.D

•To stop a countdown operation completely, first pause it

(by pressing ), and then press . This returns theD B

countdown time to its starting value.

Countdown Timer

The countdown timer can be set within a range of one

minute to 24 hours. An alarm sounds when the countdown

reaches zero. The countdown timer also has an auto-

repeat feature and a progress beeper that signals the

progress of the countdown.

•All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Configuring the Countdown Timer

The following are the settings you should configure before

actually using the countdown timer.

Countdown start time; Auto-repeat on/off; Progress

beeper on/off

•See “To configure the countdown timer for information”

about setting up the timer.

Seconds

Hours

Minutes

Setting

Hours, Minutes

Auto-repeat

Progress Beeper

Screen Button Operation

Use D (+) and B (–) to change the setting.

Press D to toggle auto-repeat on ( displayed) and off

( displayed).

Press ).D to toggle the progress beeper on ( ) and off (

Alarm time

(Hour : Minutes)

Alarm number

Alarm on indicator

Alarm date

(Month – Day)

Alarm Types

The alarm type is determined by the settings you make, as described below.

••

• Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

••

• Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

••

• 1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at the time you set, only during the month you set.

••

• Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at the time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, use D or B to scroll through the

alarm screens until the one whose time you want to set

is displayed.

•To set a one-time alarm, display an alarm screen AL1, , .AL2 AL3, or AL4

To set the snooze alarm, display the SNZ screen.

•The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

•This operation turns on the alarm automatically.

3. Press C to move the flashing in the sequence shown below to select other settings.

Hour Minutes Month Day

4. While a setting is flashing, use D and B to change it as described below.

Screen To do this:

Change the hour

and minutes

Change the

month and day

Do this:

Use ).D (+) and B (–

•With the 12-hour format, set the time correctly as a.m.

or p.m. (P indicator).

•To set an alarm that does not include a month and/or

day, set for each setting.

Snooze alarm

indicator

Hourly time signal

on indicator

Auto-repeat

When auto-repeat is turned on, the countdown restarts automatically from the

countdown start time when it reaches zero.

When auto-repeat is turned off, the countdown stops when it reaches zero and the

display shows the original countdown start time.

•Pressing D while an auto-repeat countdown is in progress pauses the current

countdown. You can resume the auto-repeat countdown by pressing , or you canD

press A to reset to the countdown time starting value.

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed

about the countdown status without looking at the display. The following describes the

types of beeper operations the watch performs during a countdown.

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero.

•When the progress beeper is turned off, the countdown end beeper sounds for

about 10 seconds, or until you press any button to stop it.

•When the progress beeper is turned on, the countdown end beeper sounds for

about one second.

Progress Beeper

When the progress beeper is turned on, the watch uses beeps to signal countdown

progress as described below.

•Starting from five minutes before the end of the countdown, the watch emits four

short beeps at the top of each countdown minute.

•30 seconds before the end of the countdown, the watch emits four short beeps.

•The watch emits a short beep for each of the last 10 seconds of the countdown.

•If the countdown start time is six minutes or greater, the watch emits a short beep for

each second of the final 10 seconds before the five-minute point is reached. Four

short beeps are emitted to signal when the five-minute point is reached.

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down until the currentA

countdown start time starts to flash, which indicates the

setting screen.

•If the countdown start time is not displayed, use the

procedure under To use the countdown timer“ ” to

display it.

2. Press to move the flashing in the sequence shownC

below to select other settings.

Hours

Progress Beeper

Minutes

Auto-repeat

3. When the setting you want to change is flashing, use B and D to change it as

described below.

Operation Guide 3031

Button Operation Tone

The button operation tone sounds any time you press one

of the watch s buttons. You can turn the button operation’

tone on or off as desired.

•Even if you turn off the button operation tone, the

alarms, the Hourly Time Signal, the countdown alarm,

and stopwatch auto start all operate normally.

To turn the button operation tone on and off

In any mode (except when a setting screen is on the

display), hold down to toggle the button operation toneC

on ( not displayed) and off ( displayed).MUTE MUTE

•Holding down C to turn the button operation tone on or off also causes the watch’s

current mode to change.

•The MUTE indicator is displayed in all modes when the button operation tone is

turned off.

Auto Return Features

•If you leave the watch in the Alarm Mode for two or three minutes without performing

any operation, it automatically changes to the Timekeeping Mode.

•If you leave a screen with flashing digits on the display for two or three minutes

without performing any operation, the watch automatically exits the setting screen.

Scrolling

The B and D buttons are used in various modes and setting screens to scroll

through data on the display. In most cases, holding down these buttons during a scroll

operation scrolls at high speed.

Initial Screens

When you enter the World Time or Alarm Mode, the data you were viewing when you

last exited the mode appears first.

Timekeeping

•Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to 00 without changing the minutes.

•The year can be set in the range of 2000 to 2099.

•The watch’s built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to change

it except after you have the watch s battery replaced.’

World Time

All World Time Mode times are calculated from the current Home City time in the

Timekeeping Mode using UTC time differential values.

•The seconds count of the World Time is synchronized with the seconds count of the

Timekeeping Mode.

•The UTC differential is a value that indicates the time difference between a

reference point in Greenwich, England and the time zone where a city is located.

•The letters “ ” “UTC is the abbreviation for Coordinated Universal Time , which is the”

world-wide scientific standard of timekeeping. It is based upon carefully maintained

atomic (cesium) clocks that keep time accurately to within microseconds. Leap

seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s

rotation.

Flash Alert

When Flash Alert is turned on, the illumination flashes for

the alarms, the Hourly Time Signal, the countdown alarm,

and stopwatch (ST1) auto start.

To turn Flash Alert on and off

In the Timekeeping Mode, hold down for about threeD

seconds to toggle Flash Alert on (Flash Alert indicator

displayed) or off (Flash Alert indicator not displayed).

•Illumination flashes twice when you turn Flash Alert on

and once when turn Flash Alert off.

•While Flash Alert is turned on, the Flash Alert indicator

remains on the display in all modes.

•Note that pressing D to toggle Flash Alert on or off will

also switch timekeeping between 12-hour and 24-hour

format.

About the Auto Light Switch

While the auto light switch is enabled, illumination turns on whenever you position

your wrist as described below in any mode.

Moving the watch to a position that is parallel to the ground and then tilting it

towards you at more than 40 degrees causes illumination to turn on.

• Wear the watch on the outside of your wrist.

Warning!

•Always make sure you are in a safe place whenever you are reading the watch

using the auto light switch. Be especially careful when running or engaged in

any other activity that can result in accident or injury. Also take care that

sudden illumination by the auto light switch does not startle or distract others

around you.

•When you are wearing the watch, make sure that its auto light switch is turned

off before riding on a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create

a distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down for about three seconds to toggle the autoB

light switch on (auto light switch indicator displayed) or off (auto light switch indicator

not displayed).

•The auto light switch indicator is on the display in all modes while the auto light

switch is turned on.

•In order to protect against running down the battery, the auto light switch turns off

automatically approximately six hours after you turn it on.

To illuminate the display

In any mode, press to turn on illumination.L

•The above operation turns on illumination regardless of the current auto light switch

setting.

•You can use the procedure below to select either 3 seconds or 5 seconds as the

illumination duration. When you press , the illumination will remain on for aboutL

3 seconds or 5 seconds, depending on the current illumination duration setting.

To specify the illumination duration

1. In the Timekeeping Mode, hold down until theA

seconds start to flash, which indicates the setting

screen.

2. While the seconds are flashing, press to toggle theB

setting between 3 seconds ( ) and 5 seconds ( ).

3. Press to exit the setting screen.A

Illumination

This watch has two EL (electro-luminescent) panels that

cause the entire display to glow for easy reading in the

dark. The watch’s auto light switch turns on illumination

automatically when you angle the watch for reading

towards your face.

•The auto light switch must be turned on (indicated by

the auto light switch indicator) for it to operate.

•See “Illumination Precautions” for more important

information.

World Time

World Time shows the current time in 48 cities (29 time

zones) around the world.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

To view the time for another city code

In the World Time Mode, press to scroll eastwardlyD

through city codes.

In the World Time Mode, press B to scroll westwardly

through city codes.

•For full information about city codes, see the “City Code

Table”.

•If the current time for a city is wrong, check your

Timekeeping Mode time and time zone settings and

make necessary changes.

Current time and date in

the zone of the selected

city code

City code

Auto light switch indicator

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D B (east) and (west) to

display the city code (time zone) whose Standard Time/

Daylight Saving Time setting you want to change.

2. Hold down A for about one second to toggle Daylight

Saving Time (DST displayed) and Standard Time (DST

not displayed).

•The DST indicator is on the display whenever you

display a city code for which Daylight Saving Time is

turned on.

•Note that the DST/Standard Time setting affects only the

currently displayed city code. Other city codes are not

affected.

DST indicator

Parallel to ground More than 40

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Graphic Areas

There are three graphic areas named A, B, and C. The information shown in each

graphic area depends on the current mode.

Graphic area B

Graphic area A

Graphic area C

•The following table shows the information that appears in graphic area A.

Flash Alert indicator

•In all modes, graphic area B shows the Stopwatch Mode (ST1) minutes (one

segment each for 5 minutes, 10 minutes, etc.).

•In all modes, graphic area C shows the Stopwatch Mode (ST2) minutes (one

segment each for 5 minutes, 10 minutes, etc.).

Mode

Timekeeping

World Time

Stopwatch (ST1 and ST2)

Countdown Timer

Alarm

Graphic Area A

Timekeeping Mode seconds

Sweeps from left to right

Sweeps from right to left

No indication

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	G9000-1V
Timer:	24 h
Gewicht:	56 g
Breedte:	46.3 mm
Diepte:	16.3 mm
Hoogte:	52 mm
LED backlight:	Ja
Type horloge:	Horloge
Type wijzerplaat horloge:	Lcd-wijzerplaat
Waterdicht:	Ja
Stopwatch:	Ja
Countdown timer:	Ja
Waterbestendig druk:	20 ATM
Waterbestendig diepte:	200 m
Schokbestendig:	Ja
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Klokmodus:	12/24 uur
Nauwkeurigheid:	±15 sec/maand
Type kalender:	Overdag
Horlogekast materiaal:	Resin,Stainless steel
Kleur behuizing:	Zwart
Band materiaal:	Kunststof
Hoofdkleur van band:	Zwart
Glas type van horloge:	Mineraalglas
Hoesvorm:	Rond
Levensduur batterij/accu:	3 jaar
Ondersteund aantal accu's/batterijen:	1
Type batterij:	CR2025