Casio G-Shock GWM850-1 Handleiding

Casio Horloge G-Shock GWM850-1

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio G-Shock GWM850-1 (8 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Operation Guide 3155

MO080 -EA7

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run

down. Make sure the watch is exposed to light as much as

possible.

• When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

• You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is only partially covered.

Bright Light

Solar cell

• The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch

settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

• The actual level at which some functions are disabled depends on the watch model.

• Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a

single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window

Approximately about 8 hours exposure to indoor fluorescent lighting

• Be sure to read “Power Supply” for important information you need to know

when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

• See “Power Saving Function” for more information.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

About This Manual

• Depending on the model of your watch, display text appears either as dark figures

on a light background or light figures on a dark background. All sample displays in

this manual are shown using dark figures on a light background.

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

General Guide

• Press C to change from mode to mode.

• In any mode (except when a setting screen is on the display), press L to illuminate

the display.

Timekeeping Mode

Press .CCountdown Timer

Mode

Stopwatch Mode Alarm Mode

▲

Rally Mode Recall Mode

▲

World Time Mode

▲

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

• This watch is designed to pick up the time calibration signals transmitted in Germany

(Mainflingen), England (Anthorn), the United States (Fort Collins), China

(Shangqiu), and Japan (Fukushima, Fukuoka/Saga).

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time calibration

signal. You also can perform a manual procedure to set the time and date, when

necessary.

• The first thing you should do after purchasing this watch is to specify your

Home City (the city where you normally will use the watch). For more

information, see “To specify your Home City” below.

• When using the watch outside the areas covered by the time signal transmitters, you

will have to adjust the current time setting manually as required. See “Timekeeping”

for more information about manual time settings.

• The U.S. time calibration signal can be picked up by the watch while in North

America. The term “North America” in this manual refers to the area that consists of

Canada, the continental United States, and Mexico.

To specify your Home City

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press D B (east) and (west) to select the city code

you want to use as your Home City.

LIS, LON

: Lisbon, London

MAD BER STO , PAR, ROM, , : Madrid, Paris,

Rome, Berlin, Stockholm

ATH : Athens

MOW : Moscow

HKG BJS TPE, , : Hong Kong, Beijing, Taipei

SEL, TYO : Seoul, Tokyo

HNL : Honolulu

ANC : Anchorage

City code

Hour : Minutes

PM indicator Seconds

YVR LAX, : Vancouver, Los Angeles

YEA DEN, : Edmonton, Denver

MEX CHI, : Mexico City, Chicago

MIA YTO NYC , , : Miami, Toronto, New York

YHZ : Halifax

YYT : St.Johns

3. Press A to exit the setting screen.

• Normally, your watch should show the correct time as soon as you select your Home

City code. If it does not, it should adjust automatically after the next auto receive

operation (in the middle of the night). You also can perform manual receive or you

can set the time manually.

• The watch will receive the time calibration signal automatically from the applicable

transmitter (in the middle of the night) and update its settings accordingly. For

information about the relationship between city codes and transmitters, see “Time

Calibration Signal Reception” and “Transmitters”.

• See the maps under “Approximate Reception Ranges” for information about the

reception ranges of the watch.

• You can disable time signal reception, if you want. See “To turn auto receive on and

off” for more information.

• Under factory default settings, auto receive is turned off for all of the following city

codes: MOW HNL ANC (Moscow), (Honolulu), and (Anchorage). For details about

turning on auto receive for these city codes, see “To turn auto receive on and off”.

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal:

auto receive and manual receive.

• Auto Receive

With auto receive, the watch receives the time calibration signal automatically up to 6

times a day (5 times a day for the Chinese calibration signal). When any auto receive

is successful, the remaining auto receive operations are not performed. For more

information, see “About Auto Receive”.

• Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a

button. For more information, see “To perform manual receive”.

Important!

• When getting ready to receive the time calibration signal, position the watch as

shown in the nearby illustration, with its 12 o’clock side facing towards a window.

This watch is designed to receive a time calibration signal late at night. Because of

this, you should place the watch near a window as shown in the illustration when you

take it off at night. Make sure there are no metal objects nearby.

12 o’clock

• Make sure the watch is facing the right way.

• Proper signal reception can be difficult or even impossible under the conditions listed

below.

Inside or

among

buildings

Inside a

vehicle

Near a

construction

site, airport, or

other sources of

electrical noise

Near high-

tension

power lines

Among or

behind

mountains

Near household

appliances, office

equipment,

or a mobile

phone

Operation Guide 3155

• Signal reception normally is better at night than during the day.

• Time calibration signal reception takes from two to seven minutes, but in some

cases it can take as long as 14 minutes. Take care that you do not perform any

button operations or move the watch during this time.

• The time calibration signal the watch will attempt to pick up depends on its current

Home City code setting as shown below.

* The areas covered by the HNL, ANC, and MOW city codes are quite far from the

time calibration signal transmitters, and so certain conditions may cause

problems with signal reception.

• Calibration signal reception is disabled while a countdown timer/target time

operation is in progress.

Home City Code

LON, PAR, BER, ATH,

LIS, MAD, ROM, STO, MOW*

HKG, BJS

TPE, TYO, SEL

HNL*, ANC*, LAX, DEN,

CHI, NYC, YVR, YEA, MEX,

MIA, YTO, YHZ, YYT

Frequency

60.0 kHz

77.5 kHz

68.5 kHz

40.0 kHz

60.0 kHz

Transmitter

Anthorn (England)

Mainflingen (Germany)

Shangqiu City (China)

Fukushima (Japan)

Fukuoka/Saga (Japan)

Fort Collins, Colorado

(the United States)

Approximate Reception Ranges

U.K. and German Signals

Anthorn

1,500 kilometers

500 kilometers

The Anthorn

signal is

receivable within

this area.

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Mainflingen

Fort Collins

U.S. Signal

Japan Signals

Signals are receivable in the Taiwan area when reception conditions are good.

1,000 kilometers1,000 kilometers

Fukuoka/Saga

500 kilometers

Fukushima

500 kilometers

1,500 kilometers

Shanghai

Hong Kong

Chengdu

Shangqiu

China Signal Changchun

Beijing

• Signal reception may not be possible at the distances noted below during certain

times of the year or day. Radio interference may also cause problems with reception.

Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310

miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 1500 kilometers (910 miles)

• Even when the watch is within the reception range of the transmitter, signal

reception will be impossible if the signal is blocked by mountains or other geological

formations between the watch and signal source.

• Signal reception is affected by weather, atmospheric conditions, and seasonal

changes.

• See the information under “Signal Reception Troubleshooting” if you experience

problems with time calibration signal reception.

About Auto Receive

The watch receives the time calibration signal automatically up to 6 times a day

(5 times a day for the Chinese calibration signal). When any auto receive is

successful, the remaining auto receive operations are not performed. The reception

schedule (calibration times) depends on your currently selected Home City, and

whether standard time or Daylight Saving Time is selected for your Home City.

Your Home City Auto Receive Start Times

1 2 3 4 5 6

Standard Time 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight*

Daylight 2:00 am 3:00 am 4:00 am 5:00 am Midnight* 1:00 am*

Saving Time

Standard Time 2:00 am 3:00 am 4:00 am 5:00 am Midnight* 1:00 am*

Daylight 3:00 am 4:00 am 5:00 am Midnight* 1:00 am* 2:00 am*

Saving Time

LON,

LIS

PAR,

BER,

MAD,

ROM,

STO

Standard Time 3:00 am 4:00 am 5:00 am Midnight* 1:00 am* 2:00 am*

Daylight 4:00 am 5:00 am Midnight* 1:00 am* 2:00 am* 3:00 am*

Saving Time

Standard Time 4:00 am 5:00 am Midnight* 1:00 am* 2:00 am* 3:00 am*

Daylight 5:00 am Midnight* 1:00 am* 2:00 am* 3:00 am* 4:00 am*

Saving Time

Standard Time 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

and Daylight

Saving Time

Standard Time Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

ATH

MOW

HKG,

BJS

TYO,

TPE,

SEL

Your Home City Auto Receive Start Times

1 2 3 4 5 6

Standard Time Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

and Daylight

Saving Time

*Next day

HNL,

ANC,

LAX,

DEN,

CHI,

NYC,

YVR,

YEA,

MEX,

MIA,

YTO,

YHZ,

YYT

Note

• When a calibration time is reached, the watch will receive the calibration signal only

if it is in either the Timekeeping Mode or World Time Mode. Reception is not

performed if a calibration time is reached while you are configuring settings.

• Auto receive of the calibration signal is designed to be performed early in the

morning, while you sleep (provided that the Timekeeping Mode time is set correctly).

Before going to bed for the night, remove the watch from your wrist, and put it in a

location where it can receive the signal easily.

• The watch receives the calibration signal for two to seven minutes everyday when

the time in the Timekeeping Mode reaches a calibration time. Do not perform any

button operation within seven minutes before or after the calibration times. Doing so

can interfere with correct calibration.

• Remember that reception of the calibration signal depends on the current time in the

Timekeeping Mode. The receive operation will be performed whenever the display

shows any one of the calibration times, regardless of whether or not the displayed

time actually is the correct time.

About the Signal Strength Indicator

The signal strength indicator shows the strength of the calibration signal being

received. For best reception, be sure to keep the watch in a location where signal

strength is strongest. The signal strength indicator is displayed while an auto or

manual receive operation is in progress.

• Even in an area where signal strength is strong, it takes about 10 seconds for signal

reception to stabilize enough for the signal strength indicator to indicate signal

strength.

Signal strength indicator

Settings updated indicator

Strong

(Level 3)

Weak

(Level 1)

• Use the signal strength indicator as a guide for checking signal strength and for

finding the best location for the watch during signal receive operations.

• Following reception of the time calibration signal and calibration of the watch’s time

setting, the settings updated indicator will remain on the display in all modes. The

settings updated indicator will not be displayed if signal reception was unsuccessful

or after you adjust the current time setting manually.

• The settings updated indicator is displayed only when the watch is able to receive

both time and date data successfully. It does not appear when only time data is

received.

• The settings updated indicator indicates that at least one of the auto calibration

signal receive operations was successful. Note, however, that the settings updated

indicator disappears from the display each day when the first auto receive operation

of the day is performed.

To perform manual receive

1. Enter the Timekeeping Mode.

2. Hold down D for about two seconds until starts to

flash on the display.

• Time calibration signal reception takes from two to

seven minutes. Take care that you do not perform any

button operations or move the watch during this time.

• If the receive operation is successful, the reception

date and time appear on the display, along with the

GET indicator.

3. After manual receive is complete, press D to return to

the Timekeeping mode.

• The watch also will exit the Receive Mode if you do not

perform any button operation for about one or two

minutes.

Receiving

Receive successful

• If the latest reception fails but a previous reception was

successful, an indicator ( ) will be on the display.

The watch will enter the Receive Mode without changing

the time setting if you press D or if you do not perform

any button operation for about one or two minutes.

Note

• To interrupt a receive operation and return to the

Receive Mode, press D.

Receive failed

If there was a previously

successful reception

If no reception was

successful

Operation Guide 3155

To turn auto receive on and off

1. In the Timekeeping Mode, press D to display the last

successful receive time and date screen.

2. Hold down A until the current auto receive setting (

or OFF) starts to flash. This is the setting screen.

• Note that the setting screen will not appear if the

currently selected Home City is one that does not

support time calibration reception.

3. Press D to toggle auto receive on (ON OFF) and off ( ).

4. Press A to exit the setting screen.

• For information about city codes that support signal

receive, see “To specify your Home City”.

To check the latest signal reception results

Press D to view the last successful receive time and

date. Press again to return to the previous screen.D

On/Off status

• Enter the Timekeeping Mode

and try again.

• Select , , , LIS LON MAD PAR,

ROM, BER, STO MOW, ATH, ,

HKG, BJS, TPE, SEL TYO, ,

HNL, ANC, YVR, LAX YEA, ,

DEN MEX, , CHI MIA YTO, , ,

NYC, YHZ YYT, or as your

Home City.

• Perform manual signal receive

or wait until the next auto

signal receive operation is

performed.

• Check to make sure the watch

is in a location where it can

receive the signal.

Cannot perform

manual receive.

Auto receive is

turned on, but the

settings updated

indicator does not

appear on the

display.

• The watch is not in the Timekeeping

Mode.

• Your current Home City is not one of

the following: LIS, LON, MAD, PAR,

ROM, BER STO MOW HKG, , ATH, , ,

BJS, TPE SEL, , TYO, HNL, ANC,

YVR LAX YEA DEN, , , , MEX CHI, ,

MIA, YTO, NYC YHZ, , or YYT

• You changed the time setting

manually.

• The DST setting was changed

manually in the World Time Mode.

• You pressed a button while signal

receive was in progress.

• Even if receive is successful, the

settings updated indicator

disappears from the display each

day when the first auto receive

operation of the day is performed.

• Time data (hour, minutes, seconds)

only was received during the last

receive operation. The settings

updated indicator appears only

when time data and date data (year,

month, day) are both received.

What you should doProblem Probable Cause

Signal Reception Troubleshooting

Check the following points whenever you experience problems with signal reception.

• If the time is one hour off, the DST

setting may be incorrect.

• The Home City code setting is not

correct for the area where you are

using the watch.

Time setting is

incorrect following

signal reception.

• Change the DST setting to

Auto DST.

• Select the correct Home City

code.

• For further information, see “Important!” under “Time Calibration Signal Reception”

and “Radio-controlled Atomic Timekeeping Precautions”.

Rally Mode

The Rally Mode of your watch can be used to measure special stage elapsed time,

and to keep track of the goal target time (countdown). The Rally Mode timing

operation is shown in the illustration below.

Start point

D D Start Stop

B Record elapsed time

The watch returns to the reset

screen automatically when the

target time becomes zero.

Special stage (competitive section 42' 30" 0)

Target time (0:50)

Special stage time

measurement end Goal

Road section (non-competitive 07' 30" 0)

Remaining

target time

(hours:minutes)

Elapsed time

1/10-second indicator

Special stage elapsed

time (hours, minutes,

seconds, 1/10-second)

Remaining target time

(minutes, seconds)

Special Stage Elapsed Time Measurement

The special stage elapsed time is measured up to 99 hours, 59 minutes, 59.9

seconds. If the time exceeds this, timing reverts to zero and continues from there.

Before Starting Measurement

The watch comes with 10 preset target times (link times),

which you can use as-is or change to the value you want.

You can use the B button to select the target time you

want while the current target time is reset to its initial

value.

LT-01 0:10 LT-07 1:30

LT-02 0:20 LT-08 2:00

LT-03 0:30 LT-09 3:00

LT-04 0:40 LT-10 5:00

LT-05 0:50 OFF

LT-06 1:00

LT-05

LT-05 target time (0:50)

To change a target time

1. While the current target time is reset to its initial value in

the Rally Mode, hold down A until the display contents

start to flash. This is the setting screen.

2. Use the D B (+) and (–) buttons to select the target

(link) time you want to change.

3. Press the C button so the current target time’s hour

digit starts to flash.

4. Use the D (+) and B (–) buttons to change the hour digit value.

5. Press the C button to move the flashing to the minute digits.

6. Use the D B (+) and (–) buttons to change the minute digit value.

7. After the time is setting you want, press the A button to exit the setting screen.

You can set a target time up to 24 hours, in units of one minute.

Target (link) time

number Target time hours Target time

minutes

To start a Rally Mode time measurement

Press the button to start the auto start countdown.D

Time measurement (special stage) will start when the

auto start countdown reaches 00 seconds.

• The watch will beep and display illumination will flash

whenever the remaining auto countdown time reaches

50, 40, 30, 20, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1 and 0 seconds.

• You can cancel the auto start countdown at any point

and start time measurement (special stage) manually by

pressing the D button.

• You can cancel the countdown and return to the

countdown start screen by pressing the button whileB

a countdown is in progress.

Auto start countdown

seconds indicator

Remaining auto start

countdown time

(36 seconds indicated here)

Special Stage Timing

This section describes operations you can perform while

special stage timing is in progress.

To pause the current time on the display

While a special stage timing operation is in progress press

the D button.

• This will pause the current elapsed time (flashing) on the

display for about one or two minutes. Though the time is

frozen on the display, the watch continues the special

stage timing operation (and count down of the remaining

target time) internally.

• While a time is paused on the display, you can record it

in memory or reset the timing operation to zero. If you

don’t do anything, the display will return to the normal

elapsed time measurement screen after a few minutes.

Measured elapsed time

Target time

To record the time paused on the display

While a time is paused on the display (see above), press the button.B

• This will save the paused time in memory and display the ongoing special stage

timing operation.

• The watch has enough memory to store up to 30 measurement time records. If there

are already 30 records in memory, storing a new measurement time causes the

oldest record to be deleted automatically to make room for the new one.

To reset the timing operation to zero

While a time is paused on the display (see above), hold down the B button.

• This will reset the elapsed time operation to zero.

To cancel an ongoing elapsed time measurement operation

Hold down the B button to reset the elapsed time operation to zero.

To change screen contents during elapsed time measurement

Press the button to display the remaining target time. Note that this operation is notB

available if “OFF” is selected for the target time.

When the remaining target

time is 5 minutes or more

When the remaining target time is

less than 5 minutes

Target

time

Target

time

Remaining Target Time Alert

The watch will beep and display illumination will flash when the remaining target time

reaches the following points, 5, 3 and 1 minute, and 30, 10, 5, 4, 3, 2, and 1 second

before time up, and at time up.

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	G-Shock GWM850-1
Kleur van het product:	Zwart
Gewicht:	56 g
Stopwatch:	Ja
Waterbestendig diepte:	200 m
Schokbestendig:	Ja
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Snooze functie:	Ja
Klokmodus:	12/24 uur
Nauwkeurigheid:	+/- 30 sec/maand
Band materiaal:	Kunststof
Levensduur batterij/accu:	0.5833 jaar
Ondersteund aantal accu's/batterijen:	1
Batterij-indicator:	Ja
Zonnekracht:	Ja
Afmetingen (B x D x H):	51.5 x 42.5 x 13.9 mm
Type batterij:	CTL1616