Candy FO FPG 201 W Handleiding

Candy Oven FO FPG 201 W

Lees hieronder de 📖 handleiding in het Nederlandse voor Candy FO FPG 201 W (42 pagina's) in de categorie Oven. Deze handleiding was nuttig voor 84 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/42
Connection
An information plaque on the oven indicates the gas with which it has been regulated.
If you have the same gas supply with which the appliance has been regulated, follow
the connection instructions carefully. Otherwise, adapt the oven for the different types
of gas before reading the connection instructions.
Connection instructions - fig. 3
The oven must be connected to the gas mains via a rigid metal pipe or with a flexible
metal tube complying with UNI 9891. The ramp gas pipe fitting and the pipe must be
connected in the following two ways:
1) using a connection without a gasket on the thread (the oven connection is cone-shaped: ISO R 7);
2) interrupting a metal gasket (aluminium, copper, rubber approved for this use); by
way of example, see fig. 3.
WARNING: gas connection via a flexible rubber tube fixed onto the tube holder is
not permitted on a fitted gas oven when it is not possible to inspect the tube.
Attention
On completing the operation, check that there are no gas leaks.
Search for gas leaks using soapy water or equivalent liquids.
NEVER USE A FLAME TO CHECK FOR GAS LEAKS.
Adapting the gas used
The appliance is regulated to operate with the gas indicated on the packaging and the
appliance itself (see technical data plaque).
Fig.3
2)
1)
RAMP GASKET
FLEXIBLE TUBE
41
Technical data
Table 2
Conversion with different gas to the regulation gas used in the factory.
Identical operations for both burners:
• check the oven is disconnected from the electrical power supply
• open the oven door completely
• remove the bottom plate from the oven (fig. 4)
• remove the burner by unscrewing screw “A”
• remove injector “B” and replace it following the instructions shown in table 2 (check
there are no gas leaks on completing the operation)
• reinstall the oven burner
• put the plate back in place
FORNO
Ø Gas injector G30/G31 mm 0,73
Ø Gas injector G20/G31 mm 1,15
Ø Gas bypass G30/G31 mm 0,42
CAT. I3, I2, I2L sealed in factory
CAT. II2H3, II23 for gas G30/G31 screwed tight; for gas G20/G25
regulated for 0,72 kW capacity.
Rated capacity in kW 2,4
Minimum capacity in kW 0,72
Rated consumption of G30 in Kg/h 0,175
Rated consumption of G20 in m3/h 0,228
Rated consumption of G25 in m3/h 0,266
Position of ring nut G30/G31 mm 14
Air regulation (“X”) G20/G25 mm 5
Power supply voltage = 220V AC
Installed power = 1,.5kW (oven with electric grill)
Minimum air exchange needed for combustion is 4,8 m3/h.
Fig.4
42
Regulating the flame
Due to the different characteristics of the gases used, flames with too much or too little air
may be obtained. In this case, regulate the flame as follows (fig. 5):
•loosen screw “C” and turn ring nut “D” to position N for methane or natural gas and
position GPL for liquid propane, ensuring that the mobile index on the ring nut
corresponds with the fixed index on the burner, thereby obtaining the correct flame
(fig. 6)
Minimum regulation
The oven thermostat is equipped with a minimum bypass and it is necessary to alter
regulation if gas type is changed, in the following manner:
• Remove control knob A;
• Remove the two ring nuts on panel B by unscrewing in an anti-clockwise direction.
• Remove control panel C;
• Remove the oven bottom plate (fig. 4);
• Turn on the oven at the highest temperature for at least 10/15 minutes.
•Turn the indexed thermostat knob to 150°C, regulate the by-pass to minimum until a
reduced but stable flame is obtained. This operation should be performed with the
oven door closed.
• Use a screwdriver on the bypass screws. It is sufficient to unscrew the bypass several
turns to regulate the minimum, passing from liquid gas to methane (fig, 7).
•IMPORTANT: after regulating the burner, check the flame remains at the minimum,
by opening and closing the oven door. If the flame goes out, adapt bypass regulation.
• For operation with G30/G31 , the bypass regulation screw must be screwed tight.
On completing regulation, indicate the gas setting on the new plaque.
Fig.6
EXCESS AIR
CORRECT FLAME
INSUFFICIENT AIR
43

Product specificaties

Merk: Candy
Categorie: Oven
Model: FO FPG 201 W

Heb je hulp nodig?

Als je hulp nodig hebt met Candy FO FPG 201 W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Oven Candy

Candy

Candy FIDC N9B5 L Handleiding

2 November 2024
Candy

Candy CA6 N5B3LYTX Handleiding

20 Oktober 2024
Candy

Candy FMBC P955 E0 Handleiding

30 September 2024
Candy

Candy COS625XBLS Handleiding

30 September 2024
Candy

Candy COS625XBL Handleiding

30 September 2024
Candy

Candy FCM955XRL Handleiding

3 September 2024
Candy

Candy FCT7D415X Handleiding

3 September 2024
Candy

Candy FST100/6 X Handleiding

13 Augustus 2024
Candy

Candy PCI25XCI642C/E Handleiding

7 Augustus 2024
Candy

Candy PCS30XCHW6LB X Handleiding

30 Juli 2024

Handleiding Oven

Nieuwste handleidingen voor Oven

LG

LG MS1937CS Handleiding

20 November 2024
LG

LG MS1947CZ Handleiding

20 November 2024
Ilve

Ilve LBI90WMPAW Handleiding

20 November 2024
Ilve

Ilve OV91SNT3C Handleiding

20 November 2024
Bröhn

Bröhn BRO6010FP Handleiding

20 November 2024
Whirlpool

Whirlpool WCC28UXA Handleiding

20 November 2024
Whirlpool

Whirlpool WOI7P8FHT1SBA Handleiding

20 November 2024
Whirlpool

Whirlpool WOI4S8PPM1SB Handleiding

20 November 2024
Whirlpool

Whirlpool WOI98FPT2SBA Handleiding

20 November 2024
Whirlpool

Whirlpool WOI78HT1SSGA Handleiding

20 November 2024