Bushnell Prime 8x32 Handleiding

Bushnell Verrekijker Prime 8x32

Lees hieronder de đź“– handleiding in het Nederlandse voor Bushnell Prime 8x32 (22 pagina's) in de categorie Verrekijker. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/22
Model #: BP1025B / BP1042B / BP832B / BPR1028 / BPR1250 / BPR842 5-18
BINOCULAR OWNER’S GUIDE
PRIME™
2
Thank you for purchasing your new Bushnell® Prime™ binoculars.
This manual will help you optimize your viewing experience by explaining how you can adjust the binocular to your eyes,
and how to care for this instrument. Read the instructions carefully before using your binocular.
NEVER LOOK DIRECTLY AT THE SUN WITH YOUR BINOCULAR,
AS IT MAY CAUSE SERIOUS DAMAGE TO YOUR EYES
EYECUP ADJUSTMENT
Your Bushnell Prime binocular is fitted with eyecups that provide a comfortable view of the full image (Fig. 1, next page)
and help to exclude extraneous light. For use without eyeglasses or sunglasses, twist up the eyecups (Fig. 2, next page).
This will place your eyes farther from the binocular’s ocular lenses, at the correct eye relief distance, allowing you to see
the full field of view.
IPD (INTERPUPILLARY DISTANCE) ADJUSTMENT
The spacing between the pupils of your eyes, called “interpupillary distance,” varies from person to person. To match your
binoculars to your IPD or “eye to eye” width:
1. Point them at a white wall or blank area of the sky. Hold the binoculars and view through them as you normally would.
Don’t worry about focus yet.
2. Grasp each side of the binocular firmly. Move the left and right sides closer together or farther apart (Fig. 3, next
page) until you see a single image with no shaded areas.
FOCUS AND DIOPTER ADJUSTMENT
1. First, adjust the eyecups and IPD as described in the previous sections.
2. Using the attached lens cap or your hand, cover the objective lens on the right
side of the binocular.
3. Using the center focus knob, focus on a distant object with fine detail (e.g.,
brick wall, tree branches, etc) until it appears as sharp as possible when viewed
through the left side of the binocular.
4. Uncover the objective lens on the right side, and cover the left objective lens
while continuing to view the same object.
5. Rotate the diopter adjustment ring located directly below the right eyecup (Fig.
4), NOT the center focus knob to bring the object into focus in the right side of
the binocular. Avoid over-turning or forcing the diopter mechanism. If you are
PARTS GUIDE
* under cap (10x25 model is not tripod adaptable)
Ocular Lens A
Center Focus Knob B
Twist-Up Eyecups C
Tripod Adapter Socket* D
Objective Lens E
Diopter Adjustment Ring F
Objective Lens Covers G
A
C
B
D
E
F
G
Fig. 4 Diopter Adjustment Ring
(10x42 model shown)
ENGLISH
3
unable to bring the object into focus for your right eye by adjusting the diopter ring, make sure the left side is still
in focus (repeat steps #2-4 if necessary). The diopter adjustment essentially provides “fine focus” on one side of the
binocular (right only) to allow for slight differences in the vision of your left and right eyes.
6. Your binocular should now be adjusted for your eyes. Focusing for any distance can now be done simply by turning
the center focus knob. Make a note of your diopter setting (position of plus and minus marks on diopter ring relative
to index mark on binocular below the ring) for future reference in case the ring is moved accidentally or by another
person using your binocular.
NECKSTRAP ATTACHMENT
To attach the neckstrap, thread the ends of the neckstrap through the strap lug (Fig.
5) on each side of the binocular, then back through the plastic buckle on the strap
(Fig. 6). Adjust the position of the binoculars on your chest as they hang around
your neck to your preference, by changing the length of the strap section which
passes through the strap channel and buckle by an equal amount on each side.
If you prefer to use an aftermarket strap that has metal O-rings, attach them to a
plastic zip tie placed on the strap lugs rather than installing them directly on the lug,
to avoid damaging the finish on the binocular via contact with the rings.
TRIPOD MOUNTING (10x25 model is not tripod adaptable)
To attach the binocular to a tripod or monopod, unscrew or pull off the cap which covers the
threaded socket at the far end of the center hinge , and set it aside in a safe place. Use (Fig. 7)
a compatible binocular tripod adapter accessory (90o angle bracket), such as the Bushnell
#161002CM, to attach your full size Prime binocular to any standard tripod in a horizontal
position to provide a stable image during prolonged viewing.
WATERPROOF / FOGPROOF
Getting caught in a heavy downpour of rain, or accidentally splashing your Prime binocular during a boating excursion
won’t be a problem. The binocular is manufactured and tested to withstand water exposure up to IPX7 standards. Fogproof
protection is achieved from dry nitrogen purging that removes all internal air, which can retain moisture.
All exterior lens surfaces have our new EXO Barrier™ coating (in addition to full multi-coating). EXO Barrier, quite simply,
is the best protective lens coating technology Bushnell has ever developed. Added at the end of the coating process,
Fig. 7 Tripod Socket Cap
Fig. 5 Strap Lug Fig. 6 Strap & Buckle
Fig. 3
Interpupillary
Distance Adjustment
Wide IPD
Narrow IPD
Fig. 2 Eyecup in “Up” Position
(for use without eyeglasses)
Fig. 1 Eyecup in “Down” Position
(for use with eyeglasses)


Product specificaties

Merk: Bushnell
Categorie: Verrekijker
Model: Prime 8x32

Heb je hulp nodig?

Als je hulp nodig hebt met Bushnell Prime 8x32 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Verrekijker Bushnell

Handleiding Verrekijker

Nieuwste handleidingen voor Verrekijker