Bushnell PowerView 2 Handleiding

Bushnell Verrekijker PowerView 2

Lees hieronder de 📖 handleiding in het Nederlandse voor Bushnell PowerView 2 (22 pagina's) in de categorie Verrekijker. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/22

03-22

BINOCULAR OWNER’S GUIDE

POWERVIEW

Thank you for purchasing your new Bushnell® PowerView® 2 binoculars.

This manual will help you optimize your viewing experience by explaining how you can adjust the binocular to your eyes,

and how to care for this instrument. Read the instructions carefully before using your binocular.

NEVER LOOK DIRECTLY AT THE SUN WITH YOUR BINOCULAR,

AS IT MAY CAUSE SERIOUS DAMAGE TO YOUR EYES

EYECUP ADJUSTMENT

Your Bushnell PowerView 2 binocular is fitted with eyecups that provide a comfortable view of the full image and help to

exclude extraneous light. If you need to wear glasses when using binoculars, leave the eyecup in the “down” position (or,

for models with fold down style eyecups, fold them down) (Fig. 1, next page). For use without eyeglasses or sunglasses,

twist up the eyecups . This will place your eyes (or, for models with fold down style eyecups, simply leave them up) (Fig. 2)

farther from the binocular’s ocular lenses, at the correct eye relief distance, allowing you to see the full field of view.

IPD (INTERPUPILLARY DISTANCE) ADJUSTMENT

The spacing between the pupils of your eyes, called “interpupillary distance,” varies from person to person. To match your

binoculars to your IPD or “eye to eye” width:

1. Point them at a white wall or blank area of the sky. Hold the binoculars and view through them as you normally would.

Don’t worry about focus yet.

2. Grasp each side of the binocular firmly. Move the left and right sides closer

together or farther apart until you see a single image with no (Fig. 3, next page)

shaded areas.

FOCUS AND DIOPTER ADJUSTMENT

1. Adjust the eyecups and IPD as described in the previous sections.

2. Using the attached lens cap or your hand, cover the objective lens on the right side

of the binocular.

3. Using the center focus knob, focus on a distant object with fine detail (e.g., brick

wall, tree branches, etc) until it appears as sharp as possible when viewed through

the left side of the binocular.

4. Uncover the objective lens on the right side, and cover the left objective lens while

continuing to view the same object.

ENGLISH

PARTS GUIDE

* under socket cap (compact models are

not tripod adaptable)

** no diopter ring on compact models-

rotate entire right eyecup

Ocular Lens A

Center Focus Knob B

Eyecups C

Tripod Adapter Socket* D

Objective Lens E

Diopter Adjustment Ring** F

Fig. 4 Diopter Adjustment Ring

(10x42 roof prism model shown)

5. Rotate the diopter adjustment ring ( located directly below the right eyecup to NOT the center focus knob) (Fig. 4)

bring the object into focus in the right side of the binocular. Note: on the compact 10x and 16x models, there is no

ring; rotate the entire right eyecup to adjust diopter. Avoid over-turning or forcing the diopter mechanism. If you are

unable to bring the object into focus for your right eye by adjusting the diopter ring/eyecup, make sure the left side

is still in focus (repeat steps #2-4 if necessary). The diopter adjustment essentially provides “fine focus” on one side of

the binocular (right only) to allow for slight differences in the vision of your left and right eyes.

6. Your binocular should now be adjusted for your eyes. Focusing for any distance can now be done simply by turning

the center focus knob. Make a note of your diopter setting (position of plus and minus marks on diopter ring relative

to index mark on binocular below the ring) for future reference in case the ring is moved accidentally or by another

person using your binocular.

NECKSTRAP ATTACHMENT

To attach the neckstrap, thread the ends of the neckstrap through the strap lug (Fig.

5) on each side of the binocular, then back through the plastic buckle on the strap

(Fig. 6). Adjust the position of the binoculars on your chest as they hang around

your neck to your preference, by changing the length of the strap section which

passes through the strap channel and buckle by an equal amount on each side.

If you prefer to use an aftermarket strap that has metal O-rings, attach them to a

plastic zip tie placed on the strap lugs rather than installing them directly on the lug,

to avoid damaging the finish on the binocular via contact with the rings.

TRIPOD MOUNTING (compact models are not tripod adaptable)

To attach the binocular to a tripod or monopod, unscrew (10x42 model) or pull off (10x50,

12x50, 20x50 models) the cap which covers the threaded (1/4-20UNC) socket at the far end

of the center hinge , and set it aside in a safe place. Use a compatible binocular tripod (Fig. 7)

adapter accessory (90o angle bracket), such as the Bushnell #161002CM, to attach your full size

PowerView 2 binocular on any standard tripod in a horizontal position, to provide a stable image

during prolonged viewing, or when using high power models such as the 20x50.

Fig. 5 Strap Lug Fig. 6 Strap & Buckle

Fig. 7 Tripod Socket Cap

Fig. 3

Interpupillary Distance (IPD) Adjustment

Fig. 2 Eyecup in “Up” Position

(for use without glasses)

1 Eyecup in “Down” Position

(for use with glasses)

Wide IPD

Narrow IPD

Fold Down Style

Twist-Up Style

Product specificaties

Merk:	Bushnell
Categorie:	Verrekijker
Model:	PowerView 2
Kleur van het product:	Grijs
Gewicht:	309 g
Breedte:	139 mm
Waterdicht:	Nee
Ondersteuning voor statiefmontage:	Nee
Dichtstbijzijnde focus afstand:	5.5 m
Prisma type:	Dak
Vergroting:	16 x
Objective diameter:	32 mm
Exit pupil:	1.8 mm
Gezichtsveld (op 1000 m):	55 m
Oogafstand:	- mm
Lens-bedekking:	Multi-coated (MC)
Garantieperiode:	5 jaar