Britax-Romer Advansafix M i-Size Handleiding

Britax-Romer Autostoel Advansafix M i-Size

Lees hieronder de 📖 handleiding in het Nederlandse voor Britax-Romer Advansafix M i-Size (3 pagina's) in de categorie Autostoel. Deze handleiding was nuttig voor 80 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

BRITAX RÖMER

Kindersicherheit GmbH

Theodor-Heuss-Straße 9

89340 Leipheim

Germany

+49 (0) 8221 3670 199

BRITAX Excelsior Limited

1 Churchill Way West

Andover

Hampshire SP10 3UW

United Kingdom

+44 (0) 1264 386034

BRITAX Nordiska Barn AB

Jörgen Kocksgatan 4

SE-211 20 Malmö

Sweden

www.britax-roemer.com | hello@britax-roemer.com

BRITAX RÖMER Child Safety EMEA

30 32

32 26

21 32

08 22 20

19 19

20 21

www.britax-roemer.com

ADVANSAFIX M i-SIZE

2000033377 - 03/20

User instructions

76 - 150 cm

TAKING CARE OF THE HARNESS BUCKLE

To ensure the safety of your child, it is essential that the harness buckle continues

tofunction correctly. Harness buckle malfunctions are usually caused by dirt accumu-

lation or by external objects. Such malfunctions may be:

• When you press the red release button, the buckle clips are ejected only slowly.

• The buckle clips no longer engage (i.e. they pop out again when you try to push

them in).

• The buckle clips do not engage without an audible click.

• The buckle clips are dicult to push in (you feel a certain amount of resistance).

• It takes a lot of force to open the harness buckle.

Remedy

Rinse out the harness buckle so that it works perfectly again:

CLEANING THE HARNESS BUCKLE

1. Open the Velcro fastener on the crotch cushion 31 and remove it.

2. Remove the grey release plate 32 as described in Section “10. REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

3. Place the release plate 32 along with the harness buckle 20 in warm water

withsome washing-up liquid for at lease one hour.

4. Thoroughly rinse the harness buckle 20 and dry it completely.

5. Attach the grey release plate 32 as described in Section 10. “ REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

6. Attach the crotch cushion 31.

CLEANING

CAUTION Please ensure that you use only original BRITAX replacement seat

covers, as the seat cover is an integral part of the child seat and is important for

correct functioning of the system. Replacement seat covers are available from your

dealer.

CAUTION! The child seat must not be used without its cover.

• The seat cover can be removed and washed with a mild detergent in a washing

machine with the “Delicates” programme (30 °C). Please follow the instructions

onthe washing label of the seat cover.

• The shoulder cushions can be removed and washed in lukewarm soapy water.

• The plastic parts, belts, and SecureGuard can be cleaned with soapy water.

Donotuse any aggressive cleaning agents (such as solvents).

Removing the shoulder cushions

1. Loosen the shoulder straps 08 as far as possible.

2. Open the shoulder cushions 19 by the Velcro fasteners at the side.

Child seat back

3. Bring the top tether 13 forward over the front of the seat.

4. Unhook the storage pouch 14 at the top.

5. Pull out the shoulder straps 08 a little so that you can see the rubber loops

oftheshoulder cushions 19 underneath.

6. Unhook the rubber loops from the plastic bars 41 on the shoulder strap height

adjuster 42 .

7. Pull the shoulder cushions 19 forwards out of the harness slots.

Reattaching the shoulder cushions

Simply follow the steps above in reverse order.

CAUTION The shoulder cushions 19 and belts must not be twisted or swapped

over. The shoulder straps 08 must be located under the black cover band 43

inthe shoulder cushions 19 .

Removing the cover

Headrest

1. Open the two press studs 33 at the belt slots.

2. Push the headrest of the child seat to the topmost position.

3. Pull the elastic band up from the edge of the tray and pull the tabs 34 out

ofthetwo slots in the seat pan.

4. Pull the cover edge out of the gap between the seat pan and the inlay cushion.

5. Unhook the rubber loops 35 under the headrest.

Seat pan

6. Undo the Velcro fastener on the crotch cushion 31 and remove it.

7. Open the four press studs 36 on the seat and back surface.

8. Push the harness buckle 20 or SecureGuard 26 through the cover slot.

9. Unhook the rubber loops 37 at the front under the seat surface and pull the tabs

38 out of the seat pan.

10. Pull the rubber loops carefully out of the gap around the belt guides 28 .

11. Pull the cover edge and tabs 39 out of the gap between the seat pan

andtheinlay cushion.

12. Pull the rubber loops 40 at the top of the back of the backrest out of the gap

inthe seat pan and and unhook them.

Reattaching the cover:

Simply follow the steps above in reverse order.

36 37

28 40

CAUTION! If the child seat is installed with Method , always install the harness A

buckle 20 correctly, and if installed with Method B, always install SecureGuard

26 correctly. Make sure that the release plate 32 is correctly attached.

CAUTION! Check that the straps are not twisted and are laid correctly through

the slots in the cover. The rear slot in the seat cover is provided for the harness

buckle 20 and the front slot is provided for the SecureGuard 26 . The slot at the

front edge of the seat is for the harness adjusting strap 22 .

3. CARE AND MAINTENANCE1. GENERAL SAFETY INSTRUCTIONS 2. USE IN THE VEHICLE

Please take the time to read these instructions carefully and always keep

them in the storage pouch provided

14 on the child seat for later reference.

The instructions must accompany the child seat if it is later passed on to

athird party.

DANGER! For the protection of your child:

• Before closing the vehicle door, check that neither your child nor any parts

of the child seat can get jammed in the door.

• In the event of an accident at a collision velocity greater than 10 km/h, it is pos-

sible that the child seat may be damaged without the damage being immediately

visible. In this case the child seat must be replaced. Please dispose of it properly.

• Always have the child seat examined if it has been damaged (e.g. if it falls to the

ground).

• Regularly check all important parts for damage. In particular, ensure that

all the mechanical parts are fully functional.

• Never lubricate any parts of the child seat with grease or oil.

•

Never leave your child unattended in the child seat in the vehicle.

• Have your child enter and exit the vehicle on the pavement side only.

• When not in use, protect the child seat from direct exposure to sunlight.

The child seat can become very hot in direct sunshine. Children's skin is sensi-

tive and could be harmed as a result.

•

7KHPRUHVQXJO\WKHEHOW¿WVRYHU\RXUFKLOGVERG\WKHVDIHU\RXUFKLOGZLOOEH7KHUH-

fore, avoid having your child wear thick clothes under the belt.

• On long journeys, take regular breaks in order to give your child a chance to run

about and play.

• If using on the rear seat: Move the front seat far enough forward to ensure that

your child's feet will not knock against the backrest of the front seat (to prevent

the risk of injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people may

cause injury to other occupants in the vehicle. Therefore, please always ensure that ...

QRORDGEHDULQJFRQWDFWSRLQWVDUHXVHGRWKHUWKDQWKRVHVSHFL¿HGLQWKHVH

instructions and those marked on the child seat.

• the backrests of the car seats are secured (for example, check that any fold-

down rear seat bench has snapped into place).

• all heavy or sharp-edged objects present in the vehicle (e.g. on the parcel shelf)

are held securely.

• all persons in the vehicle have their seatbelts fastened.

• the child seat is secured whenever it is in the vehicle, even if it is not carrying

a child.

WARNING! For your protection when handling the child seat:

• Never use the child seat in a free-standing position, not even for testing.

•

To avoid damage, ensure that the child seat is not jammed in between hard ob-

jects (car door, seat rails, etc.).

•

Keep the child seat in a safe place when not in use. Do not place heavy objects

on the seat and do not store directly next to heat sources or in direct sunlight.

CAUTION! To protect your vehicle:

• Certain car seat covers made from more sensitive materials (e.g. velour, leather,

etc.) may show wear marks after a child seat has been used. For optimum

protection of your car seat covers, we recommend using the BRITAX RÖMER

car seat protector from our range of accessories.

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, waste incineration

Plastic parts To be placed in the corresponding container

according to the labels

Metal parts Container for metals

Belt straps Container for polyester

Buckle and clip Residual waste

9. DISPOSAL

10. REMOVING THE 5-POINT HARNESS AND RE-ATTACHING SECUREGUARD

11. RE-ATTACHING THE 5-POINT HARNESS AND REMOVING SECUREGUARD

4. Open the two press studs on the inside of the headrest cover.

5. Release the two press studs on the back of the cover .

6. Release the two press studs on the seat cover and fold the cover forwards.

Whendoing so, pull the SecureGuard 26 out of the cover.

7. Loosen the 5-point harness 09 on the child seat as far as possible.

Tip: Pull the two shoulder straps forward while pressing the adjustment button 18.

8. Release the two opened shoulder cushions 19 from the Velcro strip and fold them

around the shoulder straps 08 .

DANGER Make sure that the shoulder straps 08 pass correctly through theshoul-

der cushions 19 .

9. Remove the belt clips 21 from the recess provided on the 44 inside of the backrest.

10. Raise the grey release plate 32 and push it along with the SecureGuard 26 towards

the backrest 30 .

11. Turn the grey release plate 32 around so that the harness buckle 20 is at the top

and the SecureGuard 26 . is at the bottom

“We recommend using the 5-point harness as long as possible. Only install the Secure-

Guard when the child to be secured is taller than 102 cm.”

1. Loosen the 5-point harness on the child seat as far as possible 09 .

2. Open the harness buckle and place the belt clips 21 in the belt guides

onthesides.

3. Loosen the press studs on the backrest and fold the upper half of the cover up-

wards and the lower half downwards.

4. Insert the belt clips 21 in the recess provided on the 44 inside of the backrest.

5. Open the two shoulder cushions 19 by the Velcro fasteners on the side.

6. Push the Velcro strip of the two opened shoulder cushions 19 under the back-

restcover and attach it to the ﬂeece strip provided.

Check that the two shoulder cushions are not overlapping.

7. Pull the adjusting strap 22 to tighten the harness.

8. Release the two press studs on the seat cover and fold the cover forwards.

Whiledoing this, pull the harness buckle 20 out of the cover.

9. Raise the grey release plate 32 and push it along with the harness buckle 20

towards the backrest 30 .

10. Turn the grey release plate around 32 so that the ( ) SecureGuard B 26 is at the top

and the ( ) harness buckle A 20 .is at the bottom

11. Stow the harness buckle 20 in the recess provided and push the grey release plate

32 back into the holder until it engages with an audible click.

12. Pass the SecureGuard 26 through the slot in the cover with sow-on .B

Child seat back

1. Slide the headrest 07 to the lowest position.

2. Press the safety catch at the centre of the height change switch 45 , at the same

time moving it to the upper position.

Tip! The headrest 07 can be adjusted for body heights between 76cm and

102cm.

Child seat front

3. Fold the lower part of the headrest cover upwards and lay it over the headrest.

13. Close the two bottom press studs on the cover.

14. Close the two top press studs on the cover.

15. Close the two press studs on the upper cover of the headrest.

Child seat back

16. Press the safety catch at the centre of the group change switch 45, at the same

time moving it to the upper position.

Tip! The headrest 07 can be adjusted for body heights between 100cm and

150cm.

12. Store the SecureGuard 26 in the recess provided and push the grey release plate

32 back into its holder until it engages with an audible click.

13. Pass the harness buckle 20 through the slot in the cover which is nearer

tothebackrest.

14. Close the two bottom press studs on the cover.

15. Close the two top press studs on the cover.

16. Close the two press studs on the upper cover of the headrest.

2.3 Requirements

This child seat is approved for three installation methods, , and . Use the A B1 B2

installation method depending on the size of the child to be secured.

Tip! The installation methods can be found in Section 5 “ ” Installation & Use

[pageII].

Tip! Information on the vehicle seats can be found in the instruction manual for

the vehicle. If in doubt, refer to the manufacturer or vendor of the vehicle.

From 15 months / 76 cm – 102 cm / up to 21 kg (i-Size Universal ISOFIX)

Use installation method . The child seat may only be used on the following vehicle A

seats:

• Vehicle seats with i-Size approval.

• Vehicle seats approved for ISOFIX size class “B1” and a body weight of the child to

be secured of 9–18kg. In addition, the vehicle seat position must have a top tether

anchorage point.

100 cm – 133 cm (i-Size booster seat)

Use installation method B1 on vehicle seats with i-Size approval. The child seat may

also be used on vehicle seats which are included in the enclosed vehicle type list.

Alternatively, you may use installation method B2 on vehicle seats with i-Size ap-

proval or universal approval.

Tip! Some vehicle seats reduce the adjustability of the child seat. This aects the

“Adjust seat angle” and “Adjust headrest” functions.

133 cm - 150 cm (Speciﬁc vehicle booster seat)

Use installation method or . The child seat may only be used in vehicle seats B1 B2

that are listed in the attached vehicle type list.

Tip! The latest version of this list can be obtained from our website.

www.britax-roemer.com

2.1 Use as intended

This child seat has been designed, tested and approved according to the require-

ments of the European Standard for Child Safety Equipment (UN 129/03). It is

designed to secure a child in the vehicle. It may only be used on forward-facing or

rear-facing vehicle seats. It is a toy and is suitable for use as a seat outside not not

the vehicle.

2.2 SAFETY NOTES

Elimination of the protective function through modiﬁcations

Unauthorised technical changes can cause the protective function of the seat to be

reduced or completely eliminated. The certiﬁcation is invalidated if any modiﬁcations

are made to the child seat.

• Do not make any technical changes to the child safety seat.

• Only the manufacturer is permitted to make modiﬁcations to the child safety seat.

Risk of injury through improper use

If you do not use this product as intended, serious injury or death may result.

• secure the child seat with a 2-point seat belt. Never

• Read and follow the instruction manual for the vehicle used to transport this child

seat.

• If there is a front airbag, slide the vehicle seat a long way back.

• If in doubt, refer to the manufacturer or the vendor of the child restraint system.

• Use the child seat according to the body height of the child to be secured.

click

0506

click

1 cm

click

11 26

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.

1.2 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.

2. Place the child seat facing forward on an approved car seat.

Make sure that the backrest 30 is ﬂush with the backrest of

the car seat.

Tip! If the headrest of the car seat prevents the child seat

from being fastened properly, it should be removed (see

vehicle’s instruction manual). Secure the removed headrest

in a suitable place in the vehicle so that it will not be tossed

around.

1. PREPARATORY STEPS

1.1 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.

3. FASTENING THE ISOFIX

3.1 Position the two ISOFIX locking arms 04 directly in front of

the two insertion aids 02 .

3.2 Push the two ISOFIX locking arms 04 into the insertion aids

02 until the ISOFIX locking arms 04 engage on both sides

with an audible click.

DANGER! The green locking button 05 must be visible on

both sides indicating that the child seat is correctly fastened.

The

ADVANSAFIX M i-SIZE

is not permanently installed in the vehicle. It is simply

secured along with your child by the vehicle’s 3-point seat belt.

To adjust the seat angle:

Pull the adjustment handle 23 forwards and push/slide

the seat pan 24 into the desired position.

DANGER! The seat pan 24PXVWEH¿UPO\HQJDJHG

whatever the position. Pull on the seat pan 24 to check

that it has engaged.

TIP! You can adjust the tilt angle of the child seat 24 even

while your child is sitting on it. Tighten the vehicle seat

belt after adjusting the seat angle if you use the child seat

with the vehicle seat belt (B1 B2 and ).

7. SECURING YOUR CHILD

4. PRESSING THE CHILD SEAT BACKWARDS

Push the child seat ﬁrmly backwards as far as it will go.

5. CHECKING FOR CORRECT FASTENING

Shake the child seat to check that it is securely fastened

and check the locking buttons 05 to make sure that the two

indicators are fully green.

6. Follow the steps in Section 7 “SECURING YOUR CHILD”.

2. Place the child seat on the car seat. Ensure that the back-

rest 30 is ﬂat against the backrest of the car seat.

Tip! If the headrest of the car seat prevents the child seat

from being fastened properly, it should be removed (see

vehicle’s instruction manual). Secure the removed headrest

in a suitable place in the vehicle so that it will not be tossed

around.

3. Follow the steps in Section 7 “SECURING YOUR CHILD”.

A properly adjusted headrest 07 ensures optimal protection for

your child on the child seat. Regularly check that the height of

the headrest 07 is suitable for the body height of your child:

The headrest 07 must be adjusted so that the shoulder straps

08 are at the same level as your child’s shoulders, or slightly

higher.

A correctly adjusted headrest 07 ensures that the diagonal

belt 11 is optimally positioned and gives your child optimum

protection. Regularly check that the height of the headrest 07 is

suitable for the body height of your child:

The headrest 07 must be positioned so that two ﬁngers can be

inserted between the headrest 07 and your child's shoulders.

To adjust the height of the headrest to ﬁt your child:

1. Press and hold the adjustment handle 10 on the back ofthe

headrest 07 .

2. The headrest 07 is now unlocked and can be moved to the

desired height. When you release the adjustment handle 10 ,

the headrest 07 locks into place.

3. Place the child seat on the car seat.

4. Sit your child on the child seat and check the height.

Repeat this procedure until the headrest 07 is at thecorrect

height.

1. If your vehicle is not ﬁtted with ISOFIX insertion aids

as standard, clamp the two insertion aids 02 (which

are supplied along with the seat*), with recess facing

upwards, into the two ISOFIX ﬁxing points 01 in your

vehicle.

TIP: The ISOFIX ﬁxing points are located between

theseat surface and the backrest of the car seat.

2. Move the headrest of the car seat to its topmost position.

3. Pull the grey handle 03 at the back of the child seat until

the ISOFIX locking arms 04 are fully extended.

4. On both sides of the ISOFIX locking arms, squeeze the

04 green locking button 05 and the red release button

06 together. This ensures that both hooks on the ISOFIX

locking arms 04 are open and ready to use.

* The insertion aids make it easier to install the child seat using the ISOFIX ﬁxing points and they

prevent damage to the car seat covers. If they are not being used, remove them and keep them

in a safe place. For vehicles with a folding backrest, the insertion aids need to be removed before

folding the backrest.

Any problems that occur are usually caused by dirt or external objects on the insertion aids and

onthe hook. Remove the dirt or external objects to resolve such problems.

4.1 Preparing ISOFIX

First please read the section describing the desired installation method in Section 5.

ŹThe shoulder straps 08 must be adjusted so that they arehori-

zontal or just above your child’s shoulders.

ŹThe shoulder straps 08 must not be passed behind the child’s

back, or placed level with or above the child’s ears.

The shoulder straps are adjusted as follows:

1. Loosen the 5-point harness 09 on the child seat as far

aspossible.

2. Press and hold the adjustment handle 10 on the back ofthe

headres t07 .

3. The unlocked headrest 07 can now be moved to the desired

height. When you release the adjustment handle 10 , the

headrest 07 locks into place.

4. PREPARATORY STEPS

6. ADJUSTING THE SEAT ANGLE

100 - 150 cm

With car seat belt

100 - 150 cm

With ISOFIX + car seat belt

B1 The seat shell of the

ADVANSAFIX M i-SIZE

FDQEHXVHGLQWKUHHGLႇHUHQWUHFOLQHG

positions. The

ADVANSAFIX M i-SIZE

is approved for use as follows:

Seat angle Body height

Upright position 76 - 140 cm

Middle position 76 - 150 cm

Lying position 76 - 150 cm

4.3 Adjusting the headrest (100 - 150 cm)

4.2 Adjusting the headrest (76 - 102 cm / ≤ 21 kg)

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.

1.2 Follow the steps in Section 4.2 “ADJUSTING THE HEADREST (76 - 102 cm /

≤ 21kg)”.

76 - 102 cm / ≤ 21 kg

With ISOFIX + Top Tether

2. PREPARING THE TOP TETHER

2.1 Unhook the snap-on hook 12 of the top tether 13 from the

fastening on the back of the child seat.

3. FIXING THE TOP TETHER

Attach the snap-on hook 12 to the anchorage point recom-

mended in your vehicle's instruction manual.

CAUTION! Check that you are not using luggage hooks

instead of the top-tether anchorage points.

Look for the following symbol in your vehicle:

4. FASTENING THE ISOFIX

4.1 Position the two ISOFIX locking arms 04 directly in front of

the two insertion aids 02 .

4.2 Push the two ISOFIX locking arms 04 into the insertion aids

02 until the ISOFIX locking arms 04 engage on both sides

with an audible click.

DANGER! The green locking button 05 must be visible on

both sides indicating that the child seat is correctly fastened.

5. PRESSING THE CHILD SEAT BACKWARDS

Push the child seat ﬁrmly backwards as far as it will go.

6. CHECKING FOR CORRECT FASTENING

Shake the child seat to check that it is securely fastened

and check the locking buttons 05 to make sure that the two

indicators are fully green.

7. TIGHTENING THE TOP TETHER

Tighten the top tether 13 , until the belt tension indicator 16

turns green and the top tether 13 is tight.

2.2 Take the top tether 13 out of the pouch 14 and lay it over

the child seat.

2.3 Place the child seat in the direction of travel on an ap-

proved car seat. Adjust the backrest angle of the car seat

so that the gap between the car seat and the child seat is

as small as possible.

2.4 Take the top tether 13 and press the metal tongue 15

away from the belt to extend it, and pull the top tether 13

at the snap-on hook 12 .

2.5 Guide the top tether 13 in the middle between the bars of

the headrest 07 , for integrated headrests on the side closer

to the top tether 13 anchorage point of the vehicle.

8. LOOSEN THE SHOULDER STRAPS

To loosen the shoulder straps, press the adjustment button

18 while at the same time pulling both shoulder straps 08

forward.

Do not pull the shoulder cushions CAUTION! 19.

9. OPEN THE HARNESS BUCKLE

To open the harness buckle 20 press the red button onthe

buckle.

10. SET THE CHILD IN THE CHILD SEAT

Place your child in the child seat.

Check that the harness buckle 20 is facing forwards.

11. PLACE THE SHOULDER STRAPS

Pass the shoulder straps 08 over your child’s shoulders.

WARNING! Do not twist or swap the shoulder straps, as this

will remove their protective function.

12. FASTENING THE HARNESS BUCKLE

Take the two buckle clips 21 and hold them together before

inserting them in the harness buckle 20 – they must make an

audible click when inserted.

13. TIGHTENING THE ADJUSTMENT STRAP

Pull the adjustment strap 22 until the strap lies ﬂat andsnug

around your child’s body.

WARNING! The hip belts must be positioned aslowas possi-

ble across your child's hips.

Before each journey, in order to ensure your child’s safety, make

sure that ...

Źthe child seat is engaged on both sides with the ISOFIX locking arms 04

intheISOFIX ﬁxing points 01 and that both locking buttons 05 are fully green;

Źthe child seat is securely fastened;

Źthe top tether 13 is tight over the backrest of the car seat and the belt tension

indicator 16 is green;

Źthe child seat belts ﬁt snugly around the child’s body without causing constriction;

Źthe shoulder straps 08 are correctly adjusted and are twisted;not

Źthe shoulder cushions 19 are in the correct position for your child’s body;

Źboth buckle clips 21 are fully engaged in the harness buckle 20;

1. Sit your child in the child seat. Pullout the car seat belt,

pass it in front of your child and into the car seat belt buckle

27 .

DANGER! Check that the car seat belt is not twisted,

otherwise the full protective action of the restraint system

will be impaired.

Before every journey, for your child’s safety, check that ...

Źthe child seat is engaged on both sides with the ISOFIX locking arms in the

ISOFIX ﬁxing points and both locking buttons are fully green (only applies to B1 |

with ISOFIX and car seat belt);

Źthe child seat is securely fastened;

Źthe lap belt is passed through the dark green belt guides on both sides of the

seat cushion,

Źthe

lap belt is passed through the dark green

SecureGuard.

Źthe diagonal belt on the car’s seat belt buckle side is also passed through the

dark green belt guide on the seat cushion,

Źthe diagonal belt is passed through the light green belt holder at the headrest,

DANGER!

If your child tries to open the car’s seat belt buckle 27 or insert the

diagonal belt 11 in the dark green SecureGuard 26 , stop your vehicle immedi-

ately, or as soon as possible. Check that the child seat is correctly fastened and

that your child is correctly secured. Explain to your child the dangers caused by

such actions.

2. Insert the buckle clip in the car seat belt buckle 27 until there

is an audible click.

3. Pass the diagonal belt 11 and lap belt 25 on the car’s seat-

belt buckle side 27 into the dark green belt guide 28 on the

seat cushion.

DANGER! The car’s seatbelt buckle 27 must not be near

the dark green belt guide 28 .

4. Also pass the lap belt 25 on the other side of the seat cush-

ion into the dark green belt guide 28 .

DANGER! The lap belt 25 must be placed as low as possi-

ble over your child’s hips on both sides.

5. Pass the lap belt 25 into the dark green SecureGuard 26.

DANGER! notDo pass the diagonal belt 11 into the dark

green SecureGuard 26 .

6. Pass the diagonal belt 11 into the light green belt holder

29 at the headrest 07 so that it is fully in the belt holder 29

without twisting.

Tip! If the backrest 30 is covering the light green belt

holder 29 , you can adjust the headrest 07 upwards. The

diagonal belt 11 can then be easily inserted. You can then

adjust the headrest 07 back to the correct height.

7. Make sure that the diagonal belt 11 passes over the collar-

bone, not the neck, of your child and that the button on the

dark green belt holder is 29 fully closed.

Tip: You can adjust the height of the headrest 07 again in

the vehicle.

DANGER! The diagonal belt 11 must run diagonally back-

wards. You can adjust the belt routing with the adjustable

belt deﬂector in the vehicle.

DANGER! The diagonal belt 11 must never run forwards

towards the belt deﬂector on the vehicle. In this case, use

the child seat on the back seat only.

8. Tighten the car seat belt by pulling on the diagonal belt 11 .

5. INSTALLATION & USE

DANGER! Remove the child seat from the vehicle. Never carry the child seat in

the car if it is not fastened properly.

A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)

1. Loosen the top tether 13 by pushing the metal tongue 15

away from the belt.

2. Release the snap-on hook 12 from the anchorage point in the vehicle and lay the

top tether 13 to the front over the child seat.

3. Loosen the ISOFIX fastening on both sides by squeezing the green locking button

05 and red release button 06 together.

4. Pull the seat forward and store the top tether 13 in the storage pouch 14 and

attach the snap-on hook of the top tether 13 to the fastening on the back of the

child seat.

5. Move the ISOFIX locking arms 04 back into the seat pan 24 .

B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)

1. Press the release button on your car seat buckle

2. Open the light green belt holder 29 by pressing the button on the belt holder 29

backwards, then pull out the diagonal belt 11 .

Only for installation method with ISOFIX:

3. To release the ISOFIX ﬁtting, squeeze the green locking button 05 and red release

button 06 together, ﬁrst on one side then on the other.

4. Move the ISOFIX locking arms 04 back into the seat pan 24 .

8. REMOVING THE CHILD SEAT

8.1 UNFASTENING YOUR CHILD:

8.2 REMOVAL:

A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)

To unfasten your child, press the red button on the buckle.

B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)

To unfasten your child, use the release button of your car seat buckle.

Źthe diagonal belt runs diagonally backward,

Źthe straps are tight and twisted,not

Źthe car’s seat belt buckle is placed in the dark green belt guide on the seat not

cushion.

Product specificaties

Merk:	Britax-Romer
Categorie:	Autostoel
Model:	Advansafix M i-Size

Heb je hulp nodig?

Als je hulp nodig hebt met Britax-Romer Advansafix M i-Size stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autostoel Britax-Romer

Britax-Romer Flex Base Isense Handleiding

18 Juni 2023

Britax-Romer Dualfix iSense Handleiding

17 Juni 2023

Britax-Romer KIDFIX II XP SICT Handleiding

16 Juni 2023

Britax-Romer Trifix Handleiding

14 Juni 2023

Britax-Romer Kidfix SICT Handleiding

12 Juni 2023

Britax-Romer KID PLUS Handleiding

10 Juni 2023

Britax-Romer Max-Way Handleiding

8 Juni 2023

Britax-Romer Max-Fix Handleiding

7 Juni 2023

Britax-Romer Dualfix M I-Size Handleiding

6 Juni 2023

Britax-Romer ISOFIX Adapter Handleiding

5 Juni 2023

Handleiding Autostoel

Nieuwste handleidingen voor Autostoel

Cybex Base G Handleiding

1 December 2024

Cybex Cloud G i-Size Handleiding

1 December 2024

Infasecure Raptor Plus Handleiding

16 November 2024

Cybex Sirona G i-Size Handleiding

16 November 2024

Cybex Base One Handleiding

16 November 2024

Cybex Sirona Gi i-Size Handleiding

16 November 2024

Silver Cross Reef Universal Car Seat Adaptors Handleiding

15 November 2024

Silver Cross Simplicity Plus Handleiding

15 November 2024

Evenflo Revolve360 Rotational Handleiding

14 November 2024

Petex Basic Plus 1601 Handleiding

12 November 2024