Bowers And Wilkins Performance Series CWM652 Handleiding

Bowers And Wilkins Speaker Performance Series CWM652

Lees hieronder de 📖 handleiding in het Nederlandse voor Bowers And Wilkins Performance Series CWM652 (3 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
English
CWM6
5
4.2 If speaker cable is already present in the wall
space, pull the cable down through the aperture. If
speaker cables are not already installed this should be
done at this stage. It is likely that you will need to gain
access through the oor above to route the cables
down into the wall cavity.
Leave enough spare cable through the aperture to
ease connection to the speaker frame, but not so
much that it is likely to buzz or rattle when pushed
back up into the wall space. Approximately 1.0m (3 ft)
is appropriate.
Note: Always use high quality, low resistance
speaker cable. Low resistance is especially
important if the length of cable from amplifier to
speaker exceeds 5m. Your local Bowers & Wilkins
retailer will be able to offer advice on speaker cable
selection if required.
4.3 Now connect the speaker cable to the spring
terminals on the side of the frame. Ensure that the
speaker connection polarity is correct: the cable
connected to the positive terminal on the amplier
should be connected to the red spring terminal on the
frame. Similarly, the cable connected to the negative
terminal on the amplier should be connected to the
black spring terminal on the frame. The diagram above
illustrates cable connection.
Note: If an amplifier is already connected to the
cable it should be switched off while connections
are being made to the frame.
4.4 With the frame connected it may be inserted into
the wall aperture. Ensure that the QuickDogs™ (spring
clamps) are rotated so that they will pass through the
aperture then insert the frame up so that the ange
is ush on the wall. Take care that the cable is not
trapped. Now reach inside the aperture, rotate the
QuickDogs™ outwards and, using two ngers and
thumb, pull each spring clamp downwards so that the
frame is xed securely. There are four QuickDogs™ on
the CWM652 and six on the CWM663 and CWM664.
The diagram above illustrates insertion of the frame.
Note: To release a spring clamp push the metal tab,
located just below the finger platform, upwards.
4.5 If the frame ange is to be painted it should be
done at this stage. Any conventional, domestic paint
may be applied by brushing, rolling or spraying. Use
the supplied paint mask to avoid getting paint in the
cavity. Painting without using the paint mask risks
contamination of the internal connection terminals or
the grille attachment magnets. The diagram above
illustrates painting using the paint mask.
Note: If the grille is to be painted this should be
done “off-line” before it is fitted.
6
4.6 The bafe can now be tted into the frame. Ensure
that the connector on the bafe is oriented correctly
with the connector in the frame. The bafe is hinged
into place along its bottom edge and secured at the
top by two push-lock fasteners. Push-lock fasteners
are secured by pushing the head inwards – either
with a thumb or a screwdriver. Please ensure that
the largest groove on the fastener is orientated at a
diagonal, pointing to the corner of the bafe, before
pushing the fastener. As they secure, the fasteners
will click. The bafe will then be secure in the frame.
The diagram above illustrates inserting the bafe and
securing the push-lock fasteners.
Note: Push-lock fasteners are released by turning
anticlockwise with a screwdriver.
4.7 A three position high frequency level switch is
tted to CWM600 series models, on the front face of
the bafe. The centre position of the switch gives a
nominally level frequency response.
The HF+ boost position can be useful where the
listening environment is acoustically absorbent, for
instance where carpets, soft furnishings and curtains
predominate, or where the speakers are covered
by curtains or wall hangings. The HF- cut position
may be preferred where the listening environment is
acoustically reective, for instance where hard oors
and glass predominate. The diagram above illustrates
the level switch and its effect.
= 1x

Product specificaties

Merk: Bowers And Wilkins
Categorie: Speaker
Model: Performance Series CWM652

Heb je hulp nodig?

Als je hulp nodig hebt met Bowers And Wilkins Performance Series CWM652 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Bowers And Wilkins

Bowers And Wilkins

Bowers And Wilkins CT7.3 LCRS Handleiding

8 April 2024
Bowers And Wilkins

Bowers And Wilkins CT8 CC Handleiding

1 December 2023
Bowers And Wilkins

Bowers And Wilkins CDA-16 Handleiding

1 December 2023
Bowers And Wilkins

Bowers And Wilkins CT8.2 LCR Handleiding

1 December 2023
Bowers And Wilkins

Bowers And Wilkins BB CCM8.5 Handleiding

9 Juli 2023
Bowers And Wilkins

Bowers And Wilkins BB CWM8.5 Handleiding

7 Juli 2023
Bowers And Wilkins

Bowers And Wilkins BB CWM8.3 Handleiding

6 Juli 2023
Bowers And Wilkins

Bowers And Wilkins CM Centre Handleiding

2 Juni 2023
Bowers And Wilkins

Bowers And Wilkins CCM682 Handleiding

1 Juni 2023
Bowers And Wilkins

Bowers And Wilkins Singature 805 Handleiding

29 Mei 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Infinity

Infinity Reference 6032si Handleiding

24 November 2024
Philips

Philips TAVS510 Handleiding

24 November 2024
Philips

Philips AECS5000 Handleiding

24 November 2024
Philips

Philips AECS7100 Handleiding

24 November 2024
Philips

Philips SPA725 Handleiding

24 November 2024
Philips

Philips HTL3380 Handleiding

24 November 2024
Philips

Philips TAPB600 Handleiding

24 November 2024
Philips

Philips Fidelio FW1 Handleiding

24 November 2024
Philips

Philips Fidelio DS7650 Handleiding

23 November 2024
Braun

Braun LE03 Handleiding

23 November 2024