Boss MR6W Handleiding

Boss Speaker MR6W

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss MR6W (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
MR6B/MR6W
Installation Instructions
6.5” (165 mm) Dual Cone Marine
Full Range Speakers (1 Pair)
- 1 -
Thank you for purchasing a BOSS Audio Systems product. Please read through these
instructions carefully so you will know how to install this product properly.
Package contents
2x Speakers
8x Mounting screws and clip nuts
2x EVA gaskets
Cutout template and warranty
Specications
Full range speaker
Woofer: 6.5” (165 mm),
polypropylene cone, resin treated cloth surround
Dual cone
Output power: max 180 W
Nominal impedance: 4 Ω
Frequency response: 85 Hz-20 kHz
System sensitivity: 86 dB (1 watt/1 meter)
Speaker dimensions
A
B
C
D
E
A. Overall diameter: 7.5” (191 mm)
B. Mounting hole diameter: 5.47” (139 mm)
C. Mounting depth: 2.24” (57 mm)
D. Grill protrusion: 0.87” (22 mm)
E. Outer motor diameter: 3.7” (94 mm)
- 2 -
Installation
Important notes
Consult an expert when in doubt about installation. Professional installation is always recommended.
Prior to installation, disconnect the negative terminal of the vehicle battery.
When installing the speakers, take into consideration the risks that can arise from devices being torn away
in the case of an accident. Therefore, make sure the speakers are rmly secured and the mounting area is
sufciently stable.
If you must modify the vehicle for the speaker installation, make sure you do not impair the safety and structural
integrity of the vehicle.
Before you drill or cut any holes, investigate your vehicle’s layout very carefully. Take special care when you
work near the fuel tank, fuel lines, hydraulic lines and electrical wiring.
Mounting
If you replace your vehicle’s existing speakers, simply use the same mounting locations. Or create a cutout in your
vehicle panel for speaker installation.
1. Determine the location (e.g. side panels or dash panel) where the speakers are to be mounted.
2. Cut a mounting hole and screw holes on the mounting surface as follows:
Verify the supplied template matches the speaker and mounting cut-out.
Cut out the template along the cut line. Use the cut-out template to mark the mounting hole and screw holes
on the mounting surface. Then cut the holes for the speaker to be mounted.
3. Complete the speaker wiring connection.
4. Fasten the speaker into the mounting hole with four supplied screws and clip nuts.
Make sure the speaker sits ush across the entire mounting surface.
Make sure to properly break in speakers and not reach max volume until after two 20 minute cycles at regular
volume.
Wiring
Using high quality marine-grade speaker wires (not included), connect the speakers to the audio outputs on
your 12VDC source unit (e.g. an amplier), the positive wire to the terminal marked + and the negative wire to
the terminal marked “ ”. Make sure the wires are rmly attached to the terminals.-
Amplifier
(12V)
Speaker wires
Speaker wires
Left Right
Make sure the speakers are wired correctly at 4 ohms. Observe speaker polarity when making connections.
Avoid routing wires near any sharp or moving parts. Run wires away from other wires that may cause unwanted
noise. Insulate bare wires properly.
0722


Product specificaties

Merk: Boss
Categorie: Speaker
Model: MR6W

Heb je hulp nodig?

Als je hulp nodig hebt met Boss MR6W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Boss

Handleiding Speaker

Nieuwste handleidingen voor Speaker