Bosch WAS24460AU Handleiding

Bosch Wasmachine WAS24460AU

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Bosch WAS24460AU (6 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
1
Safety instructions

ξ‚– The washing machine is heavy - take care when lifting it.
ξ‚– Warning: frozen hoses may tear/burst. Do not install the washing machine outdoors or in
areas where there is a risk of frost.
ξ‚– The washing machine may be damaged. Do not lift by projecting components (e.g. washing
machine door).
ξ‚– In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
ξ‚– If in doubt, have the appliance connected by a technician.
ξ‚– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
ξ€ƒξ€Œ ξ‚– Dispose of packaging in an environmentally friendly manner.
ξ‚– This appliance has been identified in accordance with the European Directive 2002/96/
EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive specifies a
framework for the return and recycling of waste appliances and is valid throughout Europe.
Scope of delivery according to model Humidity in the drum is
caused by the final inspection.
Depending on the connection
ξ‚– A 24-40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers) apage 4: Water connection.
Useful tool
ξ‚– Spirit level for aligning the washing machine.
Water drainage
Elbow
for fixing the waste
water hose
Aqua-Stop Aqua-Secure Standard
Power cord
Water supply
Covers
Hose holder
2
Hose and cable lengths depending on model
Installation area
ξ‚– Stability is important to prevent the machine from wandering.
ξ‚– The installation area must be firm and level.
ξ‚– Soft floors/floor coverings such as e.g. carpets are not suitable.
If installing the appliance on a pedestal
ξ‚– It is to secure the washer dryer feet with holding brackets *. essential Γ’
If installing the appliance on a wooden joist floor
ξ‚– If possible, install the washing machine in a corner.
ξ‚– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
ξ‚– It is to secure the washing machine feet with holding brackets*. essential
*order no. WMZ 2200, WX 9756
Connection on left side or Connection on right side
Note
Note
Note
NoteNote: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
ξ‚– Aqua-Stop extension hose**, approx. 2.50 m.
ξ‚– Longer supply hose, approx. 2.20 m, for standard model.
* GB plug: left side 145cm; right side: 185cm.
** order no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
ξ‚– 60 cm cavity width required.
ξ‚– Install washing machine only under a continuous worktop that is connected firmly to the
adjacent cupboards.
~135 cm
max. 100 cm
~100 cm
~ ~95 cm 140 cm
~ ~95 cm*135 cm*
3
Removing transport bolts
ξ‚– Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
ξ‚– If transporting the appliance subsequently, always re-install the
transport bolts - this prevents damage to the machine page 6.a
ξ‚– Retain the screw and spacer.
1. Take the hoses (depending on the model) out of the holder and the elbow.
Remove the elbow.
2. Undo and remove all 4 transport bolts.
3. Take the power cord out of the holders. Remove the sleeves.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
4
Water connection depending on model
ξ‚– Risk of electric shock! Do not immerse the Aqua-Stop safety device in water (contains an
electric valve).
ξ‚– To prevent leakage or water damage, follow the instructions in this chapter.
ξ‚– : operate the washing machine with cold drinking water only.Attention
Do not connect to the mixer tap of a pressureless hot-water heater.
ξ‚– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
ξ‚– If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
ξ‚– do not kink, crush, modify or cut throughAttention:
(strength is no longer guaranteed).
Optimum water pressure in the mains: 100-1000 kPa (1-10 bar)
ξ‚– When the tap is turned on, the water flow is at least 8 l/min.
ξ‚– If the water pressure is higher, install a pressure reducing valve.
Model: Aqua-Stop
Aqua-Secure
Standard
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the connection
points are not leaking.
Attention: the screw connection is under water mains
pressure.
Water drainage
Water drainage hose:
Attention: do not kink or stretch.
Height difference between installation area and outlet:
0 - 100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out of
the sink.
Attention: the plug must not be in the plug hole. When the water is being
pumped out of the washing machine, check that the water drains away
quickly enough. Do not immerse the end of the drainage hose in the water
that has been pumped out. There is a risk that water will be drawn back
into the washing machine.
Drainage into a siphon:
Attention: secure the connection with a 24-40 mm dia. hose clip
(available from a specialist retailer).
.Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slipping out of
the drain.
min 10 mm
max.
max.
max.
max.max.
9
9
9
99 0Β°
0Β°
0Β°
0Β°0Β°
3/4
ξ‚’ξ‚’
max.
max.
max.
max.max.
9
9
9
99 0Β°
0Β°
0Β°
0Β°0Β°
3/4
ξ‚’ξ‚’
min 10 mm
5
Manufacturer (see Operating instructions)
1011 / 9000 529 988
Alignment
High levels of noise, intense vibrations and may occur due to incorrectwandering
alignment.
Aligning the washing machine with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by tuning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washing machine must not be able to wobble.
Check the alignment of the washing machine with a spirit level
and correct if necessary.
3. Tighten the lock nut against the housing.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
Electrical connection
Κ‘Connect the washing machine to an alternating current and using only a properly installed
and grounded socket.
Κ‘The mains voltage ande specifications on the washing machine must match a page 6:
Technical specifications.
Κ‘For information about the connected load and required fuse Technical apage 6:
specifications.
Κ‘Ensure that:
ξ‚– the main plug fits into the socket outlet,
ξ‚– the cable cross-section is adequate,
ξ‚– the earthing system has been installed correctly.
Κ‘A damaged power cord may be replaced by an electrician only.
A replacement power cord is available from customer service.
Κ‘Do not use multiple plugs/connectors or extension cables.
Κ‘If a residual current operated circuit-breaker is used, use only a type which features this
symbol :
Only this symbol guarantees compliance with the currently valid regulations.
Κ‘Mains plug:
ξ‚– do not insert into/pull out of the socket with damp hands.
ξ‚– do not pull the plug out of the socket by pulling on the power cord.
ξ‚– never pull out the plug while the appliance is in operation.
6
Transportation, e.g. if moving house
Before transporting the washing machine:
1. Turn off the tap/water supply.
2. Release the water pressure in the supply hose.
a Operating instructions, page 11: Filter in the water inlet hose.
3. Drain any residual detergent solution.
a Operating instructions, page 11: Drain pump.
4. Disconnect the washing machine from the power supply.
5. Remove the hoses.
Installing transport bolts:
1. Remove the covers.
2. Insert all 4 spacer. Clamp the
power cord into the holders.
Insert and tighten the screws.
The transport bolts be removed after transportation. .must a page 3
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser and start the or programme. (Depend on II Empty Spin
model)
Technical specifications
Κ‘Dimensions (width x depth x height) 60 x 60 x 85 cm
Κ‘Weight 77 kg
Κ‘Power supply Nominal voltage 220-240 V, 50 Hz
Nominal current 10 A
Nominal power 2300 W
Κ‘Water pressure 100-1000 kPa (1-10 bar)
Κ‘Test programmes According to currently valid European Standard
60456
1.
2.
7
Aqua-Stop warranty for appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages under the following conditions:
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
Installation instructions
Contents Page
Κ‹Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Κ‹Environmental disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Κ‹Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Κ‹Installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Κ‹Hose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Κ‹Built-under/Built-in appliance . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Κ‹Removing transport bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Κ‹Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Κ‹Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Κ‹Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Κ‹Transportation, e.g. if moving house . . . . . . . . . . . . . . . . . . . . 6
Κ‹Technical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Κ‹Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Washing
machine
Read these instructions before switching on the washing machine.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next owner.
en
1
Safety instructions

ξ‚– The washing machine is heavy - take care when lifting it.
ξ‚– Warning: frozen hoses may tear/burst. Do not install the washing machine outdoors or in
areas where there is a risk of frost.
ξ‚– The washing machine may be damaged. Do not lift by projecting components (e.g. washing
machine door).
ξ‚– In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
ξ‚– If in doubt, have the appliance connected by a technician.
ξ‚– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
ξ€ƒξ€Œ ξ‚– Dispose of packaging in an environmentally friendly manner.
ξ‚– This appliance has been identified in accordance with the European Directive 2002/96/
EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive specifies a
framework for the return and recycling of waste appliances and is valid throughout Europe.
Scope of delivery according to model Humidity in the drum is
caused by the final inspection.
Depending on the connection
ξ‚– A 24-40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers) apage 4: Water connection.
Useful tool
ξ‚– Spirit level for aligning the washing machine.
Water drainage
Elbow
for fixing the waste
water hose
Aqua-Stop Aqua-Secure Standard
Power cord
Water supply
Covers
Hose holder
2
Hose and cable lengths depending on model
Installation area
ξ‚– Stability is important to prevent the machine from wandering.
ξ‚– The installation area must be firm and level.
ξ‚– Soft floors/floor coverings such as e.g. carpets are not suitable.
If installing the appliance on a pedestal
ξ‚– It is to secure the washer dryer feet with holding brackets *. essential Γ’
If installing the appliance on a wooden joist floor
ξ‚– If possible, install the washing machine in a corner.
ξ‚– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
ξ‚– It is to secure the washing machine feet with holding brackets*. essential
*order no. WMZ 2200, WX 9756
Connection on left side or Connection on right side
Note
Note
Note
NoteNote: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
ξ‚– Aqua-Stop extension hose**, approx. 2.50 m.
ξ‚– Longer supply hose, approx. 2.20 m, for standard model.
* GB plug: left side 145cm; right side: 185cm.
** order no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
ξ‚– 60 cm cavity width required.
ξ‚– Install washing machine only under a continuous worktop that is connected firmly to the
adjacent cupboards.
~135 cm
max. 100 cm
~100 cm
~ ~95 cm 140 cm
~ ~95 cm*135 cm*


Product specificaties

Merk: Bosch
Categorie: Wasmachine
Model: WAS24460AU

Heb je hulp nodig?

Als je hulp nodig hebt met Bosch WAS24460AU stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasmachine Bosch

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine