Bogen MPS2 Handleiding

Bogen Speaker MPS2

Lees hieronder de 📖 handleiding in het Nederlandse voor Bogen MPS2 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
© 2010 Bogen Communications, Inc.
All rights reserved.
Specifications subject to change without notice.
54-2194-01C 1307
MPS1, MPS2
Mini Pendant Speakers
Models MPS1B /MPS2B ,(Black)
MPS1W/MPS2W (White)
Installation and Use Manual
Power Tap Selection
16-ohm or 70V
The Power Tap selector switch is used to set the
appropriate power level or impedance for your
system. Rotate the switch until the power level
you require lines up with arrow.
IMPORTANT: When connecting to a 70V amplifier,
make sure that the Tap Selector switch on the
speaker IS NOT set in the “16Ω” position.
Speaker Connection and Polarity
Speaker wiring is terminated at a snap-lock input
connector, with a positive and negative terminal.
All wiring should be done prior to installation and
then plugged into the rear of the speaker. Wire all
speaker polarities the same way.
70V System Configurations
When designing a 70V system, the total of all power tap settings of all the connected
speakers CANNOT EXCEED the output power of the 70V amplifier (amplifier power
can exceed the sum of the speaker loads).
Low-Impedance System Configurations
When wiring together multiple MPS1/2 speakers that are set to 16 ohms, it is important to
calculate (using Ohmʼs Law) the total load that these speakers present to the amplifier.
The total load impedance of the interconnected speakers cannot be lower than the
minimum load impedance rating of the low-impedance amplifier. Also, care must be
taken to ensure the amplifier cannot overdrive the speakerʼs maximum power rating.
POWER TAP
SELECTOR SWITCH
SNAP-LOCK
WIRING TERMINAL
MPS1/2
(Top View)
100W Amplifier
with 70V Output
200W Max. Low-Impedance
Amplifier
4-ohm direct
GND
EXAMPLE: 16 + 32 + 8 + 8 + 16 = 80 Watts minimum amplifier output rating.
EXAMPLE: Four 16 -ohm speakers in parallel = 4 ohms. Also in this example,
the amplifier output power rating capability should not exceed 200W (4 X 50W,
the MPS1/2).
_+
IMPORTANT: The MPS1/2 Mini Pendant is not an outdoor speaker. DO NOT expose the
speaker to rain or moisture. The MPS1/2 should be installed by qualified personnel.
NOTE: ALONG WITH THE MAIN DROP CABLE, YOU MUST ALSO
USE A
SAFETY CABLE WHEN SUSPENDING AN MPS1/2 PENDANT
SPEAKER. BE SURE TO SECURE
ALL RIGGING POINTS AND
FOLLOW ALL THE CABLE MANUFACTURERʼS
MATERIAL
RECOMMENDATIONS & INSTALLATION INSTRUCTIONS. FAILURE
TO DO SO MAY RESULT IN PROPERTY DAMAGE, INJURY
OR
DEATH, AND LEGAL LIABILITY FOR YOU AND/OR YOUR COM
PANY.
Attach the main drop cable to the MPS1/2 Main Drop Cable hole in the Suspension
Attachment located on the top of the speaker. This Main Drop Cable will be the primary
connection that will hold all the suspended speakerʼs weight to the anchor point.
Likewise, attach the Safety Cable to the Safety Cable hole in the Suspension Attachment.
This Safety Cable is meant to be a safeguard only, so when attaching to an anchor point
allow for a small amount of slack in the wire, as the Safety Cable should not bear any of
the speakerʼs direct supension weight to keep the speaker hanging level.
MPS1/2 Speaker Cable Connections
and Suspension Instructions
In addition to the Main suspension Drop Cable,
a backup Safety Cable is required for proper
installation. Use wire rope or other drop line rated
for at least 100 lbs. to ensure a proper safety
margin.
The attachment point on the structure from which
the speaker is to be anchored also must be able to
handle 100 lbs.
NOTE:
If using suspension cables with a cladding,
be sure to strip away any coating so that clamping
device being used will be pressed in direct contact
with the bare wire cores.
MAIN DROP
CABLE HOLE
MINI PENDANT
SPEAKER
MPS1/2 SUSPENSION
ATTACHMENT
SAFETY
CABLE HOLE
MAIN
DROP
CABLE
SAFETY
CABLE
TO SPEAKER
ANCHOR
POINT

Product specificaties

Merk: Bogen
Categorie: Speaker
Model: MPS2

Heb je hulp nodig?

Als je hulp nodig hebt met Bogen MPS2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Bogen

Bogen

Bogen WMT1AS Handleiding

10 December 2024
Bogen

Bogen NQ-SMS1810-SCG Handleiding

8 April 2024
Bogen

Bogen CSD1X2 Handleiding

4 Januari 2024
Bogen

Bogen CSD2X2 Handleiding

1 Juli 2023
Bogen

Bogen KFLDS30T Handleiding

30 Juni 2023
Bogen

Bogen SEC4T Handleiding

29 Juni 2023
Bogen

Bogen IG8s2M Handleiding

28 Juni 2023
Bogen

Bogen MB8TSL Handleiding

27 Juni 2023
Bogen

Bogen HFSF1 Handleiding

27 Juni 2023
Bogen

Bogen IH8A Handleiding

25 Juni 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Sven

Sven MC-5 Handleiding

20 December 2024
Sven

Sven SPS-535 Handleiding

20 December 2024
Devialet

Devialet Mania Deep Handleiding

19 December 2024
Kicker

Kicker Premium 51MSC65 Handleiding

18 December 2024
Kicker

Kicker Premium 51MSC8 Handleiding

18 December 2024
Monitor Audio

Monitor Audio Apex A10AV12 Handleiding

17 December 2024
Audac

Audac ATEO6M Handleiding

17 December 2024
Audac

Audac CIRA724I Handleiding

17 December 2024
NGS

NGS WILD Space 3 Handleiding

16 December 2024
HK Audio

HK Audio LINEAR 3 112 XA Handleiding

16 December 2024