Black And Decker FS1800RS Handleiding

Black And Decker Zaagmachine FS1800RS

Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker FS1800RS (7 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/7
• Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tool’s operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used on
another tool.
Service
• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of shock or injury.
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will
make exposed metal parts of the tool "live" and shock the operator.
• Use extra caution when cutting overhead and pay particular attention to overhead
wires which may be hidden from view. Anticipate the path of falling branches and
debris ahead of time.
• KEEP HANDS AWAY from cutting area. Never reach underneath the material for any
reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers
or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the
saw by gripping the shoe.
• KEEP BLADES SHARP. Dull blades may cause the saw to swerve or stall under pres-
sure.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles away
from face and body.
CAUTION: Wear appropriate hearing protection during use. Under some conditions
and duration of use, noise from this product may contribute to hearing loss.
WARNING: Do not operate this tool for long periods of time. Vibration caused by
the operating action of this tool may cause permanent injury to fingers, hands, and arms.
Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of
use.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min ........................minutes ......................alternating current
......................direct current n o ........................no load speed
..........................Class II Construction
........................
earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations
per minute
........................lock-on symbol ........................lock-off symbol
........................Quick Release lock-on symbol
BATTERY CAP INFORMATION
Battery storage and carrying caps are provided for use whenever the battery is out of the
tool or charger. Remove cap before placing battery in charger or tool.
WARNING: Do not store or carry battery so that metal objects can contact exposed
battery terminals. For example, do not place battery in aprons, pockets, tool boxes,
product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap.
Transporting batteries can possibly cause fires if the battery terminals inadvertently come
in contact with conductive materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR) actually prohibit
transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon
luggage) UNLESS they are properly protected from short circuits. So when transporting
individual batteries, make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit.
SAFETY WARNINGS AND INSTRUCTIONS: CHARGING THE SAW
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1) bat-
tery charger, (2) battery, and (3) product using battery.
3. CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs.
Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk
of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed
extension cords should be used, and we recommend that they be listed by Underwriters
Laboratories (U.L.). If the extension is to be used outside, the cord must be suitable for
outdoor use. Any cord marked for outdoor use can also be used for indoor work. The
letters "W" or "WA" on the cord jacket indicate that the cord is suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number of
the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than
18 gauge. When using more than one extension to make up the total length, be sure
each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
NAMEPLATE RATING AMPS – 0 – 10.0
Total Extension Cord Length (ft) 25 50 75 100 125 150
Wire Gauge 18 18 16 16 14 14
9. Use only the supplied charger when charging your saw. The use of any other charger
CAT. NO. FS1800RS FORM NO. 90503808 REV. 1 PRINTED IN CHINA Copyright©2006 Black & Decker (JUN.-06)
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
CATALOG NUMBER
FS1800RS
INSTRUCTION
MANUAL
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire and/or seri-
ous personal injury.
SAVE THESE INSTRUCTIONS
Work Area
• Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from
heat, oil, sharp edges or moving parts. Replace damaged cords immediately.
Damaged cords may create a fire.
• A battery operated tool with integral batteries or a separate battery pack must be
recharged only with the specified charger for the battery. A charger that may be
suitable for one type of battery may create a risk of fire when used with another battery.
• Use battery operated tool only with specifically designated battery pack. Use of any
other batteries may create a risk of fire.
Personal Safety
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury,
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
• Avoid accidental starting. Be sure switch is in the locked or off position before
inserting battery pack. Carrying tools with your finger on the switch or inserting the battery
pack into a tool with the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that
is left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enable better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
Tool Use and Care
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with
the switch is dangerous and must be repaired.
• Disconnect battery pack from tool or place the switch in the locked or off position
before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
• When battery pack is not in use, keep it away from other metal objects like: paper
clips, coins, keys, nails, screws or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause sparks, burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edge are less likely to bind and are easier to control.
1
1
1
1
11
1
1
1
1
11 8
8
8
8
88
8
8
8
8
88
V
V
V
V
VV
V
V
V
V
VVo
o
o
o
oo
o
o
o
o
ool
l
l
l
ll
l
l
l
l
ll t
t
t
t
tt
t
t
t
t
tt
C
C
C
C
CC
C
C
C
C
CCo
o
o
o
oo
o
o
o
o
oo r
r
r
r
rr
r
r
r
r
rrd
d
d
d
dd
d
d
d
d
ddl
l
l
l
ll
l
l
l
l
lle
e
e
e
ee
e
e
e
e
ees
s
s
s
ss
s
s
s
s
sss
s
s
s
ss
s
s
s
s
ss
R
R
R
R
RR
R
R
R
R
RR e
e
e
e
ee
e
e
e
e
eec
c
c
c
cc
c
c
c
c
cci
i
i
i
ii
i
i
i
i
iip
p
p
p
pp
p
p
p
p
ppr
r
r
r
rr
r
r
r
r
rro
o
o
o
oo
o
o
o
o
ooc
c
c
c
cc
c
c
c
c
cca
a
a
a
aa
a
a
a
a
aat
t
t
t
tt
t
t
t
t
tti
i
i
i
ii
i
i
i
i
ii n
n
n
n
nn
n
n
n
n
nng
g
g
g
gg
g
g
g
g
gg
S
S
S
S
SS
S
S
S
S
SSa
a
a
a
aa
a
a
a
a
aaw
w
w
w
ww
w
w
w
w
ww
Battery Cap
K
K
K
K
KK
K
K
K
K
KK E
E
E
E
EE
E
E
E
E
EEY
Y
Y
Y
YY
Y
Y
Y
Y
YY I
I
I
I
II
I
I
I
I
IIN
N
N
N
NN
N
N
N
N
NNF
F
F
F
FF
F
F
F
F
FFO
O
O
O
OO
O
O
O
O
OOR
R
R
R
RR
R
R
R
R
RRM
M
M
M
MM
M
M
M
M
MM A
A
A
A
AA
A
A
A
A
AAT
T
T
T
TT
T
T
T
T
TTI
I
I
I
II
I
I
I
I
II O
O
O
O
OO
O
O
O
O
OON
N
N
N
NN
N
N
N
N
NN Y
Y
Y
Y
YY
Y
Y
Y
Y
YYO
O
O
O
OO
O
O
O
O
OOU
U
U
U
UU
U
U
U
U
UU S
S
S
S
SS
S
S
S
S
SSH
H
H
H
HH
H
H
H
H
HHO
O
O
O
OO
O
O
O
O
OO U
U
U
U
UU
U
U
U
U
UUL
L
L
L
LL
L
L
L
L
LLD
D
D
D
DD
D
D
D
D
DD K
K
K
K
KK
K
K
K
K
KKN
N
N
N
NN
N
N
N
N
NNO
O
O
O
OO
O
O
O
O
OOW
W
W
W
WW
W
W
W
W
WW:
:
:
:
::
:
:
:
:
::
• Keep shoe firmly against work surface.
• Charge battery for 9 hours before first use. For more information see “CHARGING
THE POWER PACK”.
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF
YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO
BLACK & DECKER.
T
THANK
HANK YOU
YOU FOR
FOR CHOOSING
CHOOSING F
FIREST
IRESTORM
ORM! G
! G O
OT
TO
O
WWW
WWW.F
.FIREST
IREST ORMT
ORMTOOLS
OOLS.
.COM
COM/P
/PRODUCT
RODUCT R
REGISTRA
EGISTRATION
TION
T
TO
OREGISTER
REGISTER YOUR
YOUR NEW
NEW PRODUCT
PRODUCT.
.
could damage the battery or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the saw. There are no customer serviceable
parts inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate the saw or battery packs even if they are severely damaged or
completely worn out. The batteries can explode in a fire.
13. A small leakage of liquid from the battery cells may occur under extreme usage, charg-
ing or temperature conditions. This does not indicate a failure. However, if the outer
seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10
minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-
35% solution of potassium hydroxide.
IMPORTANT CHARGING NOTES
1. After normal usage, your power pack should be fully charged in 3 to 9 hours. If the
power pack is run-down completely, it may take up to 9 hours to become fully charged.
Your power pack was sent from the factory in an uncharged condition. Before attempt-
ing to use it, it must be charged for at least 9 hours.
2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This
is important and will prevent serious damage to the power pack. Longest life and best
performance can be obtained if power pack is charged when air temperature is about
75°F.
3. While charging, the charger may hum and become warm to touch. This is a normal con-
dition and does not indicate a problem.
4. If the power pack does not charge properly—(1) Check current at receptacle by plug-
ging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light
switch which turns power off when you turn out the lights. (3) Move charger and power
pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and tem-
perature are
OK, and you do not get proper charging, take or send the power pack and charger to
your local Black & Decker service center. See Tools Electric in yellow pages.
5. The power pack should be recharged when it fails to produce sufficient power on jobs
which were easily done previously. DO NOT CONTINUE using saw with its power pack
in a depleted condition.
6. To prolong power pack life, avoid leaving the power pack on charge for extended periods
of time (over 30 days without use). Although overcharging is not a safety concern, it can
significantly reduce overall power pack life.
7. When the battery is inserted into the charger, the red “Charging Indicator” light will come
on indicating that there is contact between the battery and charger. The light will stay on
as long as the battery is in the charger and the charger is plugged into a working outlet. It
WILL NOT flash, go out or change to a different color when the charging cycle is
complete.
8. The power pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before recharging.
Normal usage is the best method of discharging and recharging the batteries.
OPERATION
CAUTION: Always wear eye protection while operating this power tool.
NOTE: Before cutting any type of material, be sure it is firmly anchored or clamped to
prevent slipping.
• Place blade and shoe lightly against work to be cut.
• Switch on saw motor and allow it to obtain maximum speed before applying pressure.
• Always hold saw firmly with both hands while cutting as shown in Figure 1. Whenever
possible, the saw shoe must be held firmly against the material being cut. This will prevent
the saw from jumping or vibrating and minimize blade breakage.
TRIGGER SWITCH (FIGURE 2)
Release lock-off by switching to the unlocked position shown in Fig. 2 from either side of the
saw. Pull the trigger switch to turn the motor ON. Releasing the trigger turns the motor OFF.
NOTE: This tool has no provision to lock the switch in the ON position, and should never be
locked in the ON position by any other means.
BLADE CLAMP RELEASE LEVER (FIGURE 3)
CAUTION: TURN OFF AND REMOVE BATTERY FROM TOOL.
To install blade into saw:
1. Open blade clamp release lever to its full open position as shown in Figure 3.
2. Insert blade shank from the front.
3. Close blade clamp release lever.
To remove blade from saw:
1. Open blade clamp release lever to its full open position.
2. Remove blade.
FLUSH CUTTING (FIGURE 4)
• The compact design of the reciprocating saw motor housing and pivoting shoe permit
close cutting to floors, corners and other difficult areas.
• To maximize flush cutting capabilities, insert the blade shaft into the blade clamp with the
teeth of the blade facing up.
• Turn the saw upside down so you are as close to the work surface as possible.
WOOD CUTTING (FIGURE 5)
• Before cutting any type of wood, be sure the work piece is firmly anchored or clamped to
prevent slipping.
• Place blade and shoe lightly against work to be cut.
• Switch on saw motor before applying pressure.
• Always hold saw firmly with both hands while cutting. Whenever possible, the shoe must
be held firmly against the material being cut. This will prevent the saw from jumping or
vibrating and minimize blade breakage.
METAL CUTTING
• Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials.
• In thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will ensure
a clean cut without excess vibration or tearing of metal.
• Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage.
NOTE: You should spread a thin film of oil or other coolant along the line ahead of the saw
cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.
POCKET CUTTING - WOOD ONLY (FIGURE 6)
• Measure the surface area to be cut and mark clearly with a pencil, chalk or scriber.
• Insert pocket cutting blade in blade clamp and tighten blade clamp securely.
• Tip the saw backward until the back edge of the shoe is resting on the work surface.
• Switch motor on, permitting blade to attain maximum speed.
• Grip handle steadily and begin a slow, deliberate upward swing with the handle of the saw.
• The blade will begin to feed into material. Always be sure blade is completely through
material before continuing with pocket cut.
NOTE: In areas where blade visibility is limited, use the edge of the shoe as a guide.
PROJECT TIPS
• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while
cutting.
• When cutting, always ensure that the shoe is resting against the workpiece. This will
improve operator control and minimize vibration.
• For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to high
speed steel teeth making the blade more flexible and less prone to breaking.
TROUBLESHOOTING
Problem Possible Cause Possible Solution
• Unit will not start. • Battery not installed properly. • Check battery installation.
• Battery not charged. • Check battery charging
requirements.
• Battery will not charge. • Battery not inserted into charger. • Insert battery into charger
until red LED appears.
• Charger not plugged in. • Plug charger into a
working outlet. Refer to
“Important Charging Notes”
for more details.
• Surrounding air temperature • Move charger and tool to
too hot or too cold. a surrounding air
temperature of above 40
degree F(4,5°C) or below
105 degree F (+40,5°C).
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
MAINTENANCE
REMOVE BATTERY FROM SAW WHEN PERFORMING ANY CLEANING OR OTHER
MAINTENANCE. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various
types of commercial solvents and may be damaged by their use. Use clean cloths to
remove dirt, carbon dust etc.
• When electric tools are used on fiberglass boats, sports cars, drywall etc.,they are subject
to accelerated wear and possible premature failure, as the fiberglass chips and grindings
and drywall dust are highly abrasive to bearings, brushes, commutator, etc. During any
use on fiberglass or drywall it is extremely important that the tool be cleaned frequently by
blowing with an air jet.
LUBRICATION
Your tool was properly lubricated before leaving the factory. Once every year take or send
your tool to a Black & Decker service center, or authorized service station, for a complete
cleaning, inspection and lubrication. Tools "out of service" for long periods should be
relubricated before being put back to work.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts
ACCESSORIES
The FS1800RS FIRESTORMTM reciprocating saw will accept up to a 12 inch long blade.
Always use the shortest blade suitable for your project. Longer blades are more likely to be
bent or damaged during use. During operation some longer blades may vibrate or shake if
the saw is not kept in contact with the workpiece.
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-54-HOW-TO. (800-544-6986)
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to
recycle the battery (or battery pack) at the end of its useful life have already
been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium
batteries in the trash or municipal solid waste stream and the RBRC program provides an
environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural resources by
returning the spent nickel-cadmium battery to an authorized Black & Decker service center
or to your local retailer for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery, or call 1-800-8-BATTERY.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow
page directory under "Tools—Electric" or call: 1-800-54-HOW TO (544-6986).
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should be
made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after
345
6
ROCK TOOL UP TO NORMAL CUTTING POSITION AFTER BLADE HAS CUT THROUGH MATERIAL
BERCER L’OUTIL EN POSITION NORMALE DE COUPE ÁPRES AVOIR TRAVERSÉ MATÉRIAU AVEC LA LAME.
BALANCEE LA HERRAMIENTA HASTA LA POSICION DE CORTE NORMAL DESPUES DE HACER EL CORTE A
TRAVES DEL MATERIAL
STARTING POSITION FOR POCKET CUTTING
POSITION DE DÉPART POUR LES COUPES EN RETRAIT
POSICION DE INICIO PARA EL CORTE DE BOLSILLO
1 2
FS1800RS tool can accept any of the following 18V slide pack batteries and 18V slide
pack chargers seen in the chart below. Please see the individual charger manuals for all
safety and operating instructions.
18V Slide Pack Batteries
18V Firestorm Battery
18V FSXtreme Battery
18V FSXtreme Battery -
3 terminal
18V FSXtreme Battery -
Silver Series
18V Black & Decker Battery
FSB18
FS180BX
FS18BX
FS18SBX
HPB18
Cat. # Description
18V Slide Pack Chargers
18V Cup Charger
18V Dual Port Charger
18V Radio Charger
18V Three Port Charger
9.6V-18V Fast Charger
9.6V-24V One Hour Charger
9.6V-24V Dual Port One Hour
Charger
FS18C
FS180DC
FS18RC
5104211-00
FSMVC
FS240FC
FS2400DC
Cat. # Description
les cordons endommagés. Les cordons endommagés augmentent les risques de
secousses électriques.
• Lorsqu’on utilise un outil électrique à l’extérieur, se servir d’un cordon de rallonge
prévu pour l’extérieur, portant la mention “W-A” ou “W”. Ces cordons sont conçus
pour servir à l’extérieur et minimisent les risques de secousses électriques.
SÉCURITÉ PERSONNELLE
• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu’on utilise un
outil électrique. Ne pas s’en servir lorsqu’on est fatigué ou affaibli par des drogues, de
l’alcool ou des médicaments. De graves blessures peuvent résulter d’un moment
d’inattention lors de l’utilisation d’un outil électrique.
• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des
bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les vêtements et
les gants des pièces en mouvement qui peuvent les happer.
• Éviter les démarrages accidentels. S’assurer que l’interrupteur est en position hors
tension avant de brancher l’outil. Afin d’éviter les risques de blessures, ne pas
transporter l’outil avec le doigt sur l’interrupteur ni brancher un outil dont l’interrupteur est
en position sous tension.
• Enlever les clés de réglage avant de mettre l’outil sous tension. Une clé qui est
laissée sur une pièce rotative de l’outil présente des risques de blessures.
• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s’assure d’une
meilleure maîtrise de l’outil dans des situations imprévues grâce à une position stable et
un bon équilibre.
• Porter de l’équipement de sécurité. Toujours porter des lunettes de sécurité. Dans
certaines conditions, il faut porter des masques respiratoires, des chaussures
antidérapantes, un casque de sécurité ou des protège-tympans.
UTILISATION ET ENTRETIEN DE L’OUTIL
• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de
soutenir la pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu’elle
est retenue par la main ou le corps de l’utilisateur. Cela présente des risques de perte de
maîtrise de l’outil.
• Ne pas forcer l’outil. Utiliser l’outil approprié à la tâche. L’outil approprié fonctionne
mieux et sûrement lorsqu’on s’en sert à son rendement nominal.
• Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le cas échéant, l’outil
est dangereux et il faut le réparer.
• Débrancher l’outil de la source d’alimentation avant de le régler, d’en remplacer les
accessoires ou de le ranger. On minimise de la sorte le risque de démarrage accidentel
de l’outil.
• Ranger l’outil hors de portée des enfants et de toute autre personne qui n’en connaît
pas le fonctionnement. L’outil est dangereux entre les mains de ces personnes.
• Prendre soin des outils. S’assurer que les outils de coupe sont tranchants et
propres. Des outils bien entretenus à arêtes tranchantes ont moins tendance à se coincer
et ils se maîtrisent mieux.
• Vérifier l’alignement et les attaches des pièces mobiles, le degré d’usure des pièces
ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de l’outil.
Faire réparer un outil endommagé avant de s’en servir. Des outils mal entretenus sont la
cause de nombreux accidents.
• Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires
qui conviennent à un outil peuvent présenter des risques avec un autre outil.
ENTRETIEN
• Confier l’entretien de l’outil seulement à du personnel qualifié. Le non-respect de la
présente directive présente des risques de blessures.
• Lors de l’entretien de l’outil, utiliser seulement des pièces de rechange identiques.
Respecter les consignes relatives à l’entretien du présent guide d’utilisation. Il y a risque
de secousses électriques ou de blessures lorsqu’on utilise des pièces non autorisées ou
lorsqu’on ne respecte pas les consignes relatives à l’entretien.
CONSIGNES DE SÉCURITÉ PARTICULIÈRES
• Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en
contact avec des fils cachés ou son propre cordon, car de tels contacts peuvent
mettre les pièces métalliques de l’outil sous tension, engendrant des risques de choc
électrique.
• Faire preuve d’une grande prudence en réalisant des coupes à bout de bras afin
d’éviter les fils électriques aériens cachés. Anticiper la direction dans laquelle les
branches coupées et les débris se détacheront et tomberont au sol.
• Garder les mains éloignées des zones de coupe. Ne pas mettre les mains sous la pièce
pour quelque raison que ce soit. Saisir la section profilée à l’avant de l’outil. Ne pas mettre
les doigts ou le pouce près de la lame à va-et-vient ni de sa bride de serrage. Ne pas
stabiliser la scie en saisissant le patin.
• Maintenir les lames bien aiguisées en tout temps; les lames usées peuvent faire dévier
la scie ou faire caler le moteur lorsqu’on exerce une pression sur l’outil.
• Saisir les surfaces isolées de l'outil lorsqu'on s'en sert là où il pourrait y avoir des fils
sous tension et lorsqu'il pourrait entrer en contact avec son propre fil. En cas de
contact avec un fil sous tension, les composantes métalliques à découvert de l'outil
deviendraient sous tension et l'utilisateur subirait des secousses électriques.
AVERTISSEMENT : Certains outils électriques, tels que les sableuses, les scies, les
meules, les perceuses ou certains autres outils de construction, peuvent
produire de la poussière contenant des produits chimiques susceptibles
d’entraîner le cancer, des malformations congénitales ou pouvant être nocifs pour
le système reproductif. Parmi ces produits chimiques, on retrouve :
• le plomb dans les peintures à base de plomb,
• la silice cristalline dans les briques et le ciment et autres produits de maçonnerie,
• l’arsenic et le chrome dans le bois de sciage ayant subi un traitement chimique
(comme l’arséniate de cuivre et de chrome).
Le risque associé à de telles expositions varie selon la fréquence avec laquelle on
effectue ces travaux. Pour réduire l’exposition à de tels produits, il faut travailler dans un
endroit bien aéré et utiliser le matériel de sécurité approprié, tel un masque
anti-poussières spécialement conçu pour filtrer les particules microscopiques.
• Éviter tout contact prolongé avec la poussière soulevée par cet outil ou autres
outils électriques. Porter des vêtements de protection et nettoyer les parties
exposées du corps à l’eau savonneuse. S’assurer de bien se protéger afin d’éviter
d’absorber par la bouche, les yeux ou la peau des produits chimiques nocifs.
AVERTISSEMENT : Cet outil peut produire et répandre de la poussière susceptible
de causer des dommages sérieux et permanents au système respiratoire. Toujours
utiliser un appareil respiratoire anti-poussières approprié approuvé par le NIOSH ou
l’OSHA. Diriger les particules dans le sens opposé du visage et du corps.
MISE EN GARDE : porter un dispositif de protection personnel anti-bruit approprié
durant l’utilisation. Sous certaines conditions et pendant toute la durée de l’utilisation, le
bruit émanant de ce produit pourrait contribuer à la perte d’audition.
AVERTISSEMENT : Ne pas utiliser cet outil pendant des périodes prolongées. Les
vibrations causées par l’action de fonctionnement de l’outil peuvent blesser en
permanence les doigts, les mains et les bras. Porter des gants pour amortir les vibrations,
faire des pauses fréquentes et limiter le temps d’utilisation quotidien de l’outil.
L’étiquette de l’outil peut comporter les symboles suivants.
V ....................................volts A..........................ampères
Hz ..................................hertz W ........................watts
min..................................minutes ......................courant alternatif
................................courant continu n o ........................sous vide
.................................... Construction de classe II
............................
borne de mise à la
minute
....................................symbole d´avertissement .../min ..................tours ou courses
à la minute
..................................Symbole de verrouillage en position d’arrêt
..................................Symbole de verrouillage en position de marche
..................................Symbole de déverrouillage rapide de la position de marche
INFORMATION CONCERNANT LE CAPUCHON DU BLOC-PILE
Un capuchon est fourni avec le bloc-pile en vue d’être utilisé chaque fois qu’on retire ce
dernier de l’outil ou du chargeur en vue de le ranger ou de le transporter; enlever le
capuchon avant de remettre le bloc-pile dans le chargeur ou dans l’outil.
RÈGLES DE SÉCURITÉ GÉNÉRALES CONCERNANT LES
OUTILS À PILES
AVERTISSEMENT : LIRE, COMPRENDRE ET SUIVRE TOUTES LES DIRECTIVES
précisées ci-dessous afin d’éviter les risques de choc électrique, d’incendie ou de
blessure grave.
ZONE DE TRAVAIL
• S’assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et
des endroits sombres présentent des risques d’accidents.
• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme
celles dégagées par des liquides, des gaz ou des poussières inflammables). Les
étincelles générées par le moteur des outils électriques peuvent enflammer les poussières
ou les vapeurs.
• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu’on
utilise un outil électrique. Une distraction peut entraîner la perte de maîtrise de l’outil.
MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ
• Les outils à double isolation comportent une fiche polarisée (une lame plus large que
l’autre). La fiche n’entre que d’une façon dans une prise polarisée. Lorsque la fiche n’entre
pas à fond dans la prise, essayer de nouveau après avoir inversé les broches de la fiche. Si
la fiche n’entre toujours pas dans la prise, communiquer avec un électricien certifié afin de
faire installer une prise polarisée. Ne modifier en aucune façon la fiche. La double
isolation élimine le besoin d’un cordon trifilaire mis à la terre et d’un système
d’alimentation mis à la terre.
• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs,
des cuisinières et des réfrigérateurs. Les risques sont alors plus élevés si le corps de
l’utilisateur est mis à la terre.
• Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration
d’eau dans l’outil augmente les risques de secousses électriques.
• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter l’outil ni
tirer sur le cordon pour débrancher l’outil. Éloigner le cordon des sources de chaleur, des
flaques d’huile, des arêtes tranchantes et des pièces mobiles. Remplacer immédiatement
the sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under "Tools-
Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center.
SPECIAL WARRANTY NOTE TO CONTRACTORS:
FIRESTORMTM branded products are offered as high end consumer home use tools and
carry a HOME USE WARRANTY. These tools are designed, manufactured and tested to
meet or exceed the needs of the do-it-yourselfer in the execution of projects and repairs in
and around the home. With proper use they will provide the home owner with step up power
and performance well beyond their two year warranty. However, if you use tools for a living
and use FIRESTORMTM branded products or any of Black & Decker’s other Consumer
Home Use tools you should know that they ON THE JOBSITE CANNOT BE COVERED
UNDER OUR WARRANTY.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
I
I
I
I
II
I
I
I
I
IIM
M
M
M
MM
M
M
M
M
MM P
P
P
P
PP
P
P
P
P
PPO
O
O
O
OO
O
O
O
O
OOR
R
R
R
RR
R
R
R
R
RRT
T
T
T
TT
T
T
T
T
TTA
A
A
A
AA
A
A
A
A
AAN
N
N
N
NN
N
N
N
N
NNT
T
T
T
TT
T
T
T
T
TTS
S
S
S
SS
S
S
S
S
SS
R
R
R
R
RR
R
R
R
R
RRE
E
E
E
EE
E
E
E
E
EEN
N
N
N
NN
N
N
N
N
NNS
S
S
S
SS
S
S
S
S
SSE
E
E
E
EE
E
E
E
E
EEI
I
I
I
II
I
I
I
I
IIG
G
G
G
GG
G
G
G
G
GGN
N
N
N
NN
N
N
N
N
NNE
E
E
E
EE
E
E
E
E
EEM
M
M
M
MM
M
M
M
M
MME
E
E
E
EE
E
E
E
E
EEN
N
N
N
NN
N
N
N
N
NNT
T
T
T
TT
T
T
T
T
TTS
S
S
S
SS
S
S
S
S
SS
:
:
:
:
::
:
:
:
:
::
• Garder le patin fermement contre la surface de travail.
• Charger la pile pendant 9 heures avant d’utiliser l’outil pour la première fois. Pour
obtenir plus d’information, vois la section « CHARGEMENT DU BLOC-PILE ».
S
S
S
S
SS
S
S
S
S
SSc
c
c
c
cc
c
c
c
c
cci
i
i
i
ii
i
i
i
i
iie
e
e
e
ee
e
e
e
e
ee
a
a
a
a
aa
a
a
a
a
aal
l
l
l
ll
l
l
l
l
llt
t
t
t
tt
t
t
t
t
tte
e
e
e
ee
e
e
e
e
eer
r
r
r
rr
r
r
r
r
rrn
n
n
n
nn
n
n
n
n
nna
a
a
a
aa
a
a
a
a
aat
t
t
t
tt
t
t
t
t
tti
i
i
i
ii
i
i
i
i
iiv
v
v
v
vv
v
v
v
v
vve
e
e
e
ee
e
e
e
e
ee
s
s
s
s
ss
s
s
s
s
ss a
a
a
a
aa
a
a
a
a
aan
n
n
n
nn
n
n
n
n
nn s
s
s
s
ss
s
s
s
s
ss
f
f
f
f
ff
f
f
f
f
ff i
i
i
i
ii
i
i
i
i
iil
l
l
l
ll
l
l
l
l
ll
d
d
d
d
dd
d
d
d
d
dde
e
e
e
ee
e
e
e
e
ee
1
1
1
1
11
1
1
1
1
11 8
8
8
8
88
8
8
8
8
88
v
v
v
v
vv
v
v
v
v
vvo
o
o
o
oo
o
o
o
o
ool
l
l
l
ll
l
l
l
l
llt
t
t
t
tt
t
t
t
t
tts
s
s
s
ss
s
s
s
s
ss
Numéro de catalogue
FS1800RS
GUIDE D’UTILISATION
CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
1-800-544-6986
AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR
TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS
IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.
M
MERCI
ERCI D
D’
’A
AVOIR
VOIR CHOISI
CHOISI F
FIREST
IRESTORM
ORM ! V
! VISITEZ
ISITEZ
WWW
WWW.F
.FIREST
IRESTORMT
ORMTOOLS
OOLS.
.COM
COM/P
/PRODUCT
RODUCTR
REGISTRA
EGISTRATION
TION
POUR
POUR ENREGISTRER
ENREGISTRER VOTRE
VOTRE NOUVEAU
NOUVEAU PRODUIT
PRODUIT.
.

Product specificaties

Merk: Black And Decker
Categorie: Zaagmachine
Model: FS1800RS

Heb je hulp nodig?

Als je hulp nodig hebt met Black And Decker FS1800RS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Black And Decker

Black And Decker

Black And Decker KS550K Handleiding

26 Augustus 2024
Black And Decker

Black And Decker CS1004 Handleiding

26 Augustus 2024
Black And Decker

Black And Decker SM400 Handleiding

28 Juni 2024
Black And Decker

Black And Decker BES702 Handleiding

17 Augustus 2023
Black And Decker

Black And Decker BECS2245 Handleiding

6 Juli 2023
Black And Decker

Black And Decker KS1600L Handleiding

18 Juni 2023
Black And Decker

Black And Decker BECS1835 Handleiding

17 Juni 2023
Black And Decker

Black And Decker BECS2040 Handleiding

16 Juni 2023
Black And Decker

Black And Decker KS800S Handleiding

12 Juni 2023
Black And Decker

Black And Decker KS865KN Handleiding

11 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova

Anova E60CS Handleiding

20 December 2024
Silverline

Silverline 447132 Handleiding

19 December 2024
Silverline

Silverline 427644 Handleiding

19 December 2024
Herkules

Herkules KS 210 Profi Handleiding

17 December 2024
Total

Total TS730301 Handleiding

16 December 2024
Total

Total TJSLI8501 Handleiding

16 December 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024
Bavaria

Bavaria BJS 400 Handleiding

5 December 2024
Bavaria

Bavaria BCS 64/1 Handleiding

5 December 2024
Bavaria

Bavaria BEC 2040 TC Handleiding

5 December 2024