Black And Decker CS144 Handleiding

Black And Decker Zaagmachine CS144

Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker CS144 (7 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on

another tool.

Service

• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

Specific Safety Rules

DANGER: Keep hands away from cutting area and blade. Keep your second hand

on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be

cut by the blade.

•Keep your body positioned to either side of the saw blade, but not in line with the

saw blade. KICKBACK could cause the saw to jump backwards. (See "Causes and

Operator Prevention of Kickback").

•Do not reach underneath the work. The guard cannot protect you from the blade below

the work.

•Check lower guard for proper closing before each use. Do not operate saw if lower

guard does not move freely and close instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the

lower guard with the Retracting Lever and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

•Check the operation and condition of the lower guard spring. If the guard and the

spring are not operating properly, they must be serviced before use. Lower guard

may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

•Lower guard should be retracted manually only for special cuts such as "Pocket

Cuts" and "Compound Cuts". Raise the lower guard by Retracting Lever. As soon as

blade enters the material, lower guard must be released. For all other sawing, the lower

guard should operate automatically.

•Always observe that the lower guard is covering the blade before placing saw down

on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch

is released.

• NEVER hold piece being cut in your hands or across your leg. It is important to support

the work properly to minimize body exposure, blade binding, or loss of control.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed

metal parts of the tool "live" and shock the operator.

• When ripping, always use a rip fence or straight edge guide. This improves the

accuracy of the cut and reduces the chance for blade binding.

• Always use blades with correct size and shape (diamond vs. round) arbor holes.

Blades that do not match the mounting hardware of the saw will run eccentrically, causing

loss of control.

• Never use damaged or incorrect blade washers or bolts. The blade washers and bolt

were specially designed for your saw, for optimum performance and safety of operation.

Causes and Operator Prevention of Kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece toward the operator.

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back toward the operator.

• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the

blade can dig into the top surface of the wood causing the blade to climb out of the kerf and

jump back toward the operator.

• Kickback is the result of tool misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below:

• Maintain a firm grip on the saw and position your body and arm in a way that allows

you to resist KICKBACK forces. KICKBACK forces can be controlled by the operator, if

proper precautions are taken.

• When blade is binding or when interrupting a cut for any reason, release the trigger

and hold the saw motionless in the material until the blade comes to a complete stop.

Never attempt to remove the saw from the work or pull the saw backward while the

blade is in motion or KICKBACK may occur. Investigate and take corrective actions to

eliminate the cause of blade binding.

• When restarting a saw in the workpiece, center the saw blade in the kerf and check

that teeth are not engaged into the material. If saw blade is binding it may walk up or

KICKBACK from the workpiece as the saw is restarted.

•Support large panels to minimize the risk of blade pinching and KICKBACK. Large

panels tend to sag under their own weight. Supports must be placed under the panel on

both sides, near the line of cut and near the edge of the panel.

•Do not use dull or damaged blade. Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade binding and KICKBACK.

•Blade depth and bevel adjusting locking levers must be tight and secure before

making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.

•Use extra caution when making a "Pocket Cut" into existing walls or other blind

areas. The protruding blade may cut objects that can cause KICKBACK.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating current

......................direct current no........................no load speed

..........................

Class II Construction ........................earthing terminal

..........................safety alert symbol

.../min ................revolutions or reciprocations per minute

Additional Safety Rules: Circular Saws

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from face and

body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

•Snagging the lower guard on a surface below the material being cut can momentarily

reduce operator control. The saw can lift partially out of the cut increasing the chance of

blade twist. Ensure there is sufficient clearance under the workpiece.

• When necessary to raise lower guard manually, use the retracting lever.

•KEEP THE BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback.

The use of dull and/or dirty blades can increase the saw loading causing the operator to

push harder which promotes twisting.

DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades.

Never place hands in front of or behind the path of the blade while cutting. Do not reach

underneath work while blade is rotating. Do not attempt to remove cut material when blade

is moving.

•SUPPORT LARGE PANELS. Large panels must be supported as shown (Fig. 1) in this

manual to minimize the risk of blade pinching and kickback. When cutting operation

requires the resting of the saw on the workpiece, the saw shall be rested on the larger

portion and the smaller piece cut off.

•USE ONLY CORRECT BLADES AND BLADE ASSEMBLY COMPONENTS WHEN

MOUNTING BLADES. Do not use blades with incorrect size holes. Never use defective or

incorrect blade washers or bolts. Follow blade assembly procedures.

•ADJUSTMENTS. Before cutting be sure depth and bevel adjustments are tight.

C NAT. NO. CS144, CS180, BDCS1400, BDCS1800 FORM O. 609747-21 (MAY 04)

KEY INFORMATION YOU SHOULD KNOW:

•Carbide blades stay sharp much longer than steel blades. Use a carbide blade

whenever possible.

•Adull blade will cause slow, inefficient cutting.

•Always support work properly. (See illustrations on work support in this manual.)

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. LÉASE ESTEADVERTENCIA:

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

CS144, CS180,

BDCS1400, BDCS1800

INSTRUCTION

MANUAL

GENERAL SAFETY RULES - FOR ALL BATTERY

OPERATED TOOLS

WARNING: READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious

personal injury. SAVE THESE INSTRUCTIONS

Work Area

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from

heat, oil, sharp edges or moving parts. Replace damaged cords immediately.

Damaged cords may create a fire.

• A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. A charger that may be

suitable for one type of battery may create a risk of fire when used with another battery.

• Use battery operated tool only with specifically designated battery pack. Use of any

other batteries may create a risk of fire.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious

personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

• Avoid accidental starting. Be sure switch is in the locked or off position before

inserting battery pack. Carrying tools with your finger on the switch or inserting the battery

pack into a tool with the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tool. Such

preventive safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws or other small metal objects that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edge are less likely to bind and are easier to control.

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544-6986)

IF YOU SHOULD EXPERIENCE APROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986)

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,

TYPE No., AND DATE CODE. IN MOST CASES, A REPRESENTATIVE CANBLACK & DECKER

RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT,

GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

•SUPPORT AND SECURE THE WORK PROPERLY. Insure that the material to be cut is

clamped (Fig. 3) and solidly supported and balanced on a strong, stable and level work

surface. Support the work so that the wide portion of the saw shoe is on the portion of the

material that doesn’t fall after the cut is made. Never hold cut off piece by hand (Fig. 4 ).

KICKBACK from blade pinch can result. Keep both hands on saw at all times.

•STAY ALERT AND EXERCISE CONTROL. Keep body positioned to one side of blade.

Always maintain a firm grip and control of saw with both hands. Do not change hand grip or

body position while saw is running. Take precaution to avoid injury from cut off pieces and

other falling material during operation.

DANGER: RELEASE SWITCH IMMEDIATELY IF BLADE BINDS OR SAW STALLS.

GUARD AGAINST KICKBACK

•KICKBACK CAN BE CAUSED BY the saw blade becoming pinched, twisted or bound while

cutting, or when the saw stalls. When the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top surface of the wood causing the

blade to climb out of the cut and move suddenly back toward the operator.

TO REDUCE THE RISK OF KICKBACK

• Keep a firm grip on saw with both hands at all times.

• Stay alert – exercise control.

• Support long overhanging materials. As the material is cut and weakens, it will sag, causing

a pinched blade.

• Support large panels as shown (Fig. 1). Material supported only at the ends (Fig. 2) will lead

to blade pinching.

• Avoid sawing overhead. Material can sag and will pinch blade.

• Keep blades sharp and clean.

• Use fence or straight edge guide when ripping. Be careful as the cut off strip can sag or

twist, closing the cut and pinching the blade, leading to KICKBACK.

• Don’t force tool. Wood variables such as knots, hardness, toughness, wetness, pressure

treated and freshly cut green lumber can heavily load the saw which can lead to stalling.

Push the saw slower when this occurs.

• Don’t remove saw from work during a cut while the blade is moving.

• Allow saw to reach full speed before blade contacts material to be cut. Starting the saw with

the blade against the work or pushed forward into cut can lead to stalling or sudden

backward movement of saw.

• Never attempt to lift saw when making a bevel cut. This leads to blade binding and stalling.

• Always secure work to prevent workpiece movement during cut.

• Do not try to force saw back on line if your cut begins to go off line. This can cause

KICKBACK. Stop saw and allow blade to coast down to a stop. Withdraw from cut and start

a new cut on the line.

• Set depth adjustment of saw such that one tooth of the blade projects below the workpiece

as shown in (Fig. 6).

• Do not back up a rotating blade in the cut. Twisting the saw can cause the back edge of the

blade to dig into the material, climb out of the work and run back toward the operator.

• Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

• Some wood contains preservatives such as copper chromium arsenate (CCA) which can be

toxic. When cutting these materials, extra care should be taken to avoid inhalation and

minimize skin contact.

Safety Warnings and Instructions: Charging the saw

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary markings on (1) bat-

tery charger, (2) battery, and (3) product using battery.

3. CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs.

Other types of batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by Black & Decker may result in a risk

of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed

extension cords should be used, and we recommend that they be listed by Underwriters

Laboratories (U.L.). If the extension is to be used outside, the cord must be suitable for

outdoor use. Any cord marked for outdoor use can also be used for indoor work. The

letters "W" or "WA" on the cord jacket indicate that the cord is suitable for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number of

the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than

18 gauge. When using more than one extension to make up the total length, be sure

each extension contains at least the minimum wire size.

CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS

NAMEPLATE RATING AMPS – 0 – 10.0

Total Extension Cord Length (ft) 25 50 75 100 125 150

Wire Gauge 18 18 16 16 14 14

9. Use only the supplied charger when charging your saw. The use of any other charger

could damage the saw or create a hazardous condition.

10. Use only one charger when charging.

11. Do not attempt to open the charger or the saw. There are no customer serviceable

parts inside. Return to any authorized Black & Decker service center.

12. DO NOT incinerate the saw or battery packs even if they are severely damaged or

completely worn out. The batteries can explode in a fire.

13. A small leakage of liquid from the battery cells may occur under extreme usage,

charging or temperature conditions. This does not indicate a failure. However, if the

outer seal is broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a

25-35% solution of potassium hydroxide.

Charging the Power Pack

THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE

FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF

THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power. NOTE: Do not

charge by means of an engine generator or DC power source. Use only 120V AC.

1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.

2. Slide the charger onto the battery pack as shown in Figure A and let it charge initially

for 9 hours. After the initial charge, under normal usage, your power pack should be

fully charged in 3 to 6 hours.

3. Remove pack from the charger and place in tool. NOTE: To remove the battery from

the saw, press down on the release button on the back of the battery (Figure B) and

pull out.

Important Charging Notes

1. After normal usage, your power pack should be fully charged in 3 hours or less. If the

power pack is run-down completely, it may take up to 6 hours to become fully charged.

Your power pack was sent from the factory in an uncharged condition. Before attempt-

ing to use it, it must be charged for at least 3 hours.

2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This

is important and will prevent serious damage to the power pack. Longest life and best

performance can be obtained if the power pack is charged when the air temperature is

about 75°F.

3. While charging, the charger may hum and become warm to touch. This is a normal con-

dition and does not indicate a problem.

4. If the power pack does not charge properly—(1) Check current at receptacle by

plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a

light switch which turns power off when you turn out the lights. (3) Move charger and

power pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and

temperature are OK, and you do not get proper charging, take or send the power pack

and charger to your local Black & Decker service center. See Tools Electric in yellow

pages.

5. The power pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE using saw with its power pack

in a depleted condition.

6. To prolong power pack life, avoid leaving the power pack on charge for more than 8

hours. Although overcharging is not a safety concern, it can significantly reduce overall

power pack life.

7. When the battery is inserted into the charger, the red “Charging Indicator” light will come

on indicating that there is contact between the battery and charger. The light will stay on

as long as the battery is in the charger and the charger is plugged into a working outlet. It

WILL NOT flash, go out or change to a different color when the charging cycle is

complete.

Battery cap information

Battery storage and carrying caps are provided for use whenever the

battery is out of the tool or charger. Remove cap before placing bat-

tery in charger or tool.

WARNING! Do not store or carry battery so that metal objects can

contact exposed battery terminals. For example, do not place battery in

aprons, pockets, tool boxes, product kit boxes, drawers, etc. with loose

nails, screws, keys, etc. without battery cap. Without cap in place,

battery could short circuit causing fire or burns or damage to battery.

Blade

Lame

Disco

Inner clamp washer

Rondelle de fixation externe

Roldana de sujeción exterior

Saw spindle

Arbre de la scie

Flecha de la sierra

Blade clamping screw

Vis de fixation de la lame

Tornillo de sujeción del disco

Outer clamp washer

Rondelle de fixation externe

Roldana de sujeción interior

Direction of teeth

Sens des dents

Dirección de los dientes

Kerf Plate and Screw

Placa indicadora de

corte y tornillo

For pocket cuts only

Pour coupes en retrait seulement

Solamente para cortes de bolsillo

Correct

Correcto Wrong

Incorrect

Incorrecto

Material bends on blade causing heavy loads or kickback

Le matériau plie au contact de la lame causant de lourdes surcharges ou des rebonds.

El material oprime el disco ocasionando sobrecarga o contragolpe

Support work near cut

Soutenir la pièce près de la ligne de coupe.

Apoye la pieza cerca del corte

Correct

Correcto

Wrong

Incorrect

Incorrecto

Bevel adjustment knob

Bouton de réglage pour coupes en biseau

Perilla de ajuste de bisel

Depth adjustment lever

Bouton de réglage de la profondeur

Perilla de ajuste de profundidad

Tip of tooth

Bout de la dent

Punta del diente

Surface of wood

Surface du bois

Superficie de madera

Proper depth: one tooth below surface of wood

Profondeur appropriée : une dent sous la surface du bois.

Profundidad correcta: un diente debajo de la superficie de madera

Switch Handle

Poignée de

l’interrupteur

Mango del interruptor

Warning: When blade starts cutting, release retraction

lever immediately

Avertissement : Lorsque la lame commence à

découper, relâcher immédiatement le ressort de rappel.

Advertencia: Cuando el disco inicie el corte, suelte

inmediatamente la palanca del mecanismo retráctil

Tighten

Serrer

Apriete

Loosen

Desserrer

Afloje

Blade Wrench

Clé de réglage de la lame

Llave del disco

Switch lock-off lever

Levier de verrouillage en position «arrêt»

Palanca de seguro de apagado

Switch trigger

Interrupteur à gâchette

Interruptor de gatillo

Assembly/Adjustment Set-Up

WARNING: Always remove battery from tool before any of the following operations.

Attaching and removing the Blade

NOTE: The first time the blade bolt is removed from saw without a blade installed, it

may be necessary to place the blade wrench on the bolt head and tap it sharply in the

counter clockwise direction.

Retract lower guard and assemble blade and clamp washers, as shown in Fig. 8. To prevent

blade rotation while tightening the blade clamping screw, raise the lower guard and place

the saw down on a piece of scrap wood as shown in Fig. 9A. The blade teeth will dig into the

scrap wood and prevent rotation while you tighten the blade clamping screw. Tighten the

blade clamping screw securely, using the wrench provided. Figure 9B illustrates an

alternative method of loosening and tightening the blade by inserting a screwdriver through

the hole in the blade to prevent it from moving. NOTE: The blade wrench is stored in the kerf

plate as shown in Fig. 8.

Cutting Depth Adjustment

Adjust depth of cut using depth adjustment lever. See (Figs. 5 & 6) for proper setting.

Tighten lever securely.

Bevel Angle Adjustment

Adjust bevel angle (Fig. 7) using bevel adjustment knob and bevel scale. Tighten knob

securely.

Kerf Plate Adjustment

Adjust kerf plate (Fig. 8) to read zero when the bevel scale reads zero by loosening the kerf

plate screw and sliding the plate as necessary. Align mark on kerf plate with drawn pencil

line and advance blade into cut. The kerf plate has lines for zero bevel and 45 degree bevel

cutting.

Battery Cap

Operating Instructions

WARNING: To reduce the risk of serious personal injury, read, understand and follow all

important safety warnings and instructions prior to using tool.

GENERAL CUTS (IMPORTANT: Read safety warnings and instructions. )

GUARD AGAINST KICKBACK

With battery removed, follow all assembly, adjustment and set up instructions.

Make sure lower guard operates. Select the proper blade for the material to be cut.

• Measure and mark work for cutting.

• Support and secure work properly (See Safety Rules and Instructions).

• Use appropriate and required safety equipment (See Safety Rules).

• Secure and maintain work area (See Safety Rules).

• With battery inserted, make sure switch turns saw on and off.

WARNING: It is important to support the work properly and to hold the saw firmly to prevent

loss of control which could cause personal injury. Fig. 3 illustrates typical hand support.

Switch

Saw is equipped with a switch lock-off feature to prevent unintentional running. To operate

the tool, push down on the lock-off lever shown in Fig.9B from either side of the saw and

hold it down as you depress the trigger switch. After you have depressed the trigger and

the tool is running, release the lock-off lever. The tool will continue to run as long as the

trigger is depressed.

To turn the tool off, release the trigger switch. There is no provision for locking the tool on,

and the switch should never be locked on by any other means.

Automatic Electric Brake

Your saw is equipped with an electric blade brake which stops the saw blade within 1-1/2

seconds of trigger release. This is automatic and requires no adjustment.

Occasionally, under certain conditions, the brake will not function properly and won’t stop the

saw in the 1-1/2 seconds as discussed above. If this condition occurs, turn the saw on and off

four or five times. If the problem still persists, have the tool serviced at a Black & Decker ser-

vice center or company authorized service facility.

Pocket Cuttong (See Figure 10)

Pocket cutting is used to cut a hole in a piece of material without cutting from the

side.

• Measure and mark work.

• Tilt saw forward and rest front of the shoe on material to be cut. Align so that cut will begin

at the back of the drawn rectangle.

• Using the retracting lever, retract blade guard to an upward position, with the blade just

clearing the material, start motor and gradually lower the saw into the material.

WARNING: As blade starts cutting the material, release the retracting lever immediately.

• Never tie the blade guard in a raised position.

• When the shoe rests flat on the material being cut, complete the cut in forward direction.

• Allow the blade to come to a complete stop before lifting saw from material.

• When starting each new cut, repeat the above steps.

Maintenance

Remove battery from SAW WHEN PERFORMING ANY CLEANING OR

OTHER MAINTENANCE.

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY

and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized

service centers or other qualified service organizations, always using identical replacement

parts

Accessories

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO. (800-544-6986)

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous. Always use 5-3/8” (136 mm) diameter blades. Carbide blades are strongly

recommended for optimum saw performance. NEVER USE ABRASIVE TYPE OR METAL

CUTTING BLADES ON SAW.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs

to recycle the battery (or battery pack) at the end of its useful life have

already been paid by Black & Decker. In some areas, it is illegal to place

spent nickel-cadmium batteries in the trash or municipal solid waste stream

and the RBRC program provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery, or call 1-800-8-BATTERY.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations

throughout North America. All Black & Decker Service Centers are staffed with trained

personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact the

Black & Decker location nearest you.

To find your local service location, refer to the yellow page directory under “Tools—Electric”

or call: 1-800-54-HOW-TO. (800-544-6986)

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material

or workmanship. The defective product will be replaced or repaired at no charge in either of

two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should be

made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after

the sale). Proof of purchase may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized Service Centers are listed under “Tools-

Electric” in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state and province to province.

Should you have any questions, contact the manager of your nearest Black & Decker

Service Center. This product is not intended for commercial use.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

MESURES DE SÉCURITÉ

AVERTISSEMENT : Lire et comprendre toutes les directives. Le non-respect de toutes

les directives suivantes présente des risques de secousses électriques, d’incendie ou de

blessures graves.

CONSERVER CES MESURES.

ZONE DE TRAVAIL

• S’assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et

des endroits sombres présentent des risques d’accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme

celles dégagées par des liquides, des gaz ou des poussières inflammables). Les

étincelles générées par le moteur des outils électriques peuvent enflammer les poussières

ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu’on

utilise un outil électrique. Une distraction peut entraîner la perte de maîtrise de l’outil.

MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ

• Les outils à double isolation comportent une fiche polarisée (une lame plus large que

l’autre). La fiche n’entre que d’une façon dans une prise polarisée. Lorsque la fiche n’entre

pas à fond dans la prise, essayer de nouveau après avoir inversé les broches de la fiche. Si

la fiche n’entre toujours pas dans la prise, communiquer avec un électricien certifié afin de

faire installer une prise polarisée. Ne modifier en aucune façon la fiche. La double

isolation élimine le besoin d’un cordon trifilaire mis à la terre et d’un système

d’alimentation mis à la terre.

• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Les risques sont alors plus élevés si le corps de

l’utilisateur est mis à la terre.

• Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration

d’eau dans l’outil augmente les risques de secousses électriques.

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter l’outil ni

tirer sur le cordon pour débrancher l’outil. Éloigner le cordon des sources de chaleur, des

flaques d’huile, des arêtes tranchantes et des pièces mobiles. Remplacer immédiatement

les cordons endommagés. Les cordons endommagés augmentent les risques de

secousses électriques.

• Lorsqu’on utilise un outil électrique à l’extérieur, se servir d’un cordon de rallonge

prévu pour l’extérieur, portant la mention “W-A” ou “W”. Ces cordons sont conçus

pour servir à l’extérieur et minimisent les risques de secousses électriques.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu’on utilise un

outil électrique. Ne pas s’en servir lorsqu’on est fatigué ou affaibli par des drogues, de

l’alcool ou des médicaments. De graves blessures peuvent résulter d’un moment

d’inattention lors de l’utilisation d’un outil électrique.

• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des

bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les vêtements et

les gants des pièces en mouvement qui peuvent les happer.

• Éviter les démarrages accidentels. S’assurer que l’interrupteur est en position hors

tension avant de brancher l’outil. Afin d’éviter les risques de blessures, ne pas

transporter l’outil avec le doigt sur l’interrupteur ni brancher un outil dont l’interrupteur est

en position sous tension.

• Enlever les clés de réglage avant de mettre l’outil sous tension. Une clé qui est

laissée sur une pièce rotative de l’outil présente des risques de blessures.

• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s’assure d’une

meilleure maîtrise de l’outil dans des situations imprévues grâce à une position stable et

un bon équilibre.

• Porter de l’équipement de sécurité. Toujours porter des lunettes de sécurité. Dans

certaines conditions, il faut porter des masques respiratoires, des chaussures

antidérapantes, un casque de sécurité ou des protège-tympans.

UTILISATION ET ENTRETIEN DE L’OUTIL

• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de

soutenir la pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu’elle

est retenue par la main ou le corps de l’utilisateur. Cela présente des risques de perte de

maîtrise de l’outil.

• Ne pas forcer l’outil. Utiliser l’outil approprié à la tâche. L’outil approprié fonctionne

mieux et sûrement lorsqu’on s’en sert à son rendement nominal.

• Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le cas échéant, l’outil

est dangereux et il faut le réparer.

• Débrancher l’outil de la source d’alimentation avant de le régler, d’en remplacer les

accessoires ou de le ranger. On minimise de la sorte le risque de démarrage accidentel

de l’outil.

• Ranger l’outil hors de portée des enfants et de toute autre personne qui n’en connaît

pas le fonctionnement. L’outil est dangereux entre les mains de ces personnes.

• Prendre soin des outils. S’assurer que les outils de coupe sont tranchants et

propres. Des outils bien entretenus à arêtes tranchantes ont moins tendance à se coincer

et ils se maîtrisent mieux.

• Vérifier l’alignement et les attaches des pièces mobiles, le degré d’usure des pièces

ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de l’outil.

Faire réparer un outil endommagé avant de s’en servir. Des outils mal entretenus sont la

cause de nombreux accidents.

• Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires

qui conviennent à un outil peuvent présenter des risques avec un autre outil.

ENTRETIEN

• Confier l’entretien de l’outil seulement à du personnel qualifié. Le non-respect de la

présente directive présente des risques de blessures.

• Lors de l’entretien de l’outil, utiliser seulement des pièces de rechange identiques.

Respecter les consignes relatives à l’entretien du présent guide d’utilisation. Il y a risque

de secousses électriques ou de blessures lorsqu’on utilise des pièces non autorisées ou

lorsqu’on ne respecte pas les consignes relatives à l’entretien.

MESURES DE SÉCURITÉ SPÉCIFIQUES

DANGER :Éloigner les mains de la zone de coupe et de la lame. Laisser l’autre

main sur la poignée auxiliaire ou sur le carter du moteur. Lorsque les deux mains tiennent la

scie, la lame ne peut pas les couper.

• Se placer d’un côté ou de l’autre de la lame de la scie, jamais derrière. Un REBOND

provoquerait le saut de la scie vers l’arrière. (Voir la rubrique relatives aux cause de

rebonds et à leur prévention.)

• Ne pas placer les doigts sous la pièce à ouvrer. Le protecteur ne protège pas les doigts

de la lame sous la pièce.

• Vérifier le bon fonctionnement du protecteur inférieur avant chaque utilisation. Ne

jamais se servir de la scie lorsque le protecteur inférieur est coincé et qu’il se referme

instantanément. Ne jamais fixer ni attacher le protecteur inférieur en position ouverte. En

cas de chute accidentelle de la scie, le protecteur inférieur peut être tordu ou cassé. Le

soulever à l’aide du ressort de rappel et s’assurer de son bon fonctionnement, vérifier s’il

ne touche pas à la lame ou à tout autre composant à tous les angles et toutes les

profondeurs de coupe.

AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAI-

SON PRIÈRE DE COMPOSER

1 800 544-6986

RENSEIGNEMENTS IMPORTANTS

• Des lames au carbure restent affûtées plus longtemps que des lames en acier.

Utiliser des lames au carbure dans la mesure du possible.

• Une lame émoussée procure une coupe lente et inefficace.

• Toujours bien soutenir le matériau. (Voir les illustrations relatives au soutien du

matériau du présent guide.)

Product specificaties

Merk:	Black And Decker
Categorie:	Zaagmachine
Model:	CS144

Heb je hulp nodig?

Als je hulp nodig hebt met Black And Decker CS144 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Black And Decker

Black And Decker KS550K Handleiding

26 Augustus 2024

Black And Decker CS1004 Handleiding

26 Augustus 2024

Black And Decker SM400 Handleiding

28 Juni 2024

Black And Decker BES702 Handleiding

17 Augustus 2023

Black And Decker BECS2245 Handleiding

6 Juli 2023

Black And Decker KS1600L Handleiding

18 Juni 2023

Black And Decker BECS1835 Handleiding

17 Juni 2023

Black And Decker BECS2040 Handleiding

16 Juni 2023

Black And Decker KS800S Handleiding

12 Juni 2023

Black And Decker KS865KN Handleiding

11 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova E60CS Handleiding

20 December 2024

Silverline 447132 Handleiding

19 December 2024

Silverline 427644 Handleiding

19 December 2024

Herkules KS 210 Profi Handleiding

17 December 2024

Total TS730301 Handleiding

16 December 2024

Total TJSLI8501 Handleiding

16 December 2024

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024

Bavaria BJS 400 Handleiding

5 December 2024

Bavaria BCS 64/1 Handleiding

5 December 2024

Bavaria BEC 2040 TC Handleiding

5 December 2024