Bertazzoni DB36600X-P92V Handleiding

Bertazzoni Fornuis DB36600X-P92V

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Bertazzoni DB36600X-P92V (23 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/23
(GB) INSTRUCTIONS FOR THE INSTALLATION, MAINTENANCE
pag. 2 AND USE OF FIXED HOBS WITH GAS OR MIXED SUPPLY
DROP IN (TYPE P92/P92V)
(FR) INSTRUCTIONS POUR L'INSTALLATION, L'ENTRETIEN ET
page. 7 L'UTILISATION DES TABLES DE CUISSON ENCASTRABLES
GAZ ET MIXTES
DROP IN (MODELE P92/P92V)
(NL) INSTRUCTIES VOOR INSTALLATIE, ONDERHOUD EN
pag. 12 GEBRUIK VAN INGEBOUWDE GASKOOKPLATEN (TYPE
P92/P92V)
(GB) READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE.
These instructions are valid only for those countries which are indicated by their identiļ¬cation symbol on the front cover of
the instruction booklet and on the label on the appliance.
The manufacturer cannot be held responsible for any damage to things or persons caused by an incorrect installation or by
incorrect use of the appliance.
The manufacturer cannot be held responsible for any inaccuracies due to errors in printing or writing contained in this booklet. The
appearance of the ļ¬gures shown is also only approximate.
The manufacturer reserves the right to make changes to his products when it is considered necessary and useful without eļ¬€ecting the
essential features regarding safety and function.
INDEX:
TECHNICAL MANUAL FOR THE INSTALLER ........................................................................................................ pag. 2
Inserting the hob ........................................................................................................... pag. 2 ..............................................
Fixing the hob Advice about installation ................................................................................................... pag. 3 ā€“................
Ventilation and airing of the premises Connection to the gas supply ....................................................................... pag. 3 ā€“
Adaptation to diļ¬€erent types of gas ....................................................................................... pag. 3 .....................................
Regulation of the burners ................................................................................................... pag. 4 .........................................
Connection to the electricity supply .................... pag. 4 .........................................................................................................
MAINTENANCE OF THE APPLIANCE Replacing parts ........................................................................................ pag. 4 ā€“
USE AND MAINTENANCE MANUAL .................................................................................................. pag. 5 ......................
Description of types of hobs ........................................................................ pag. 5 ................................................................
Use of the burners .......................................................................................................... pag. 5 .............................................
Cleaning of the appliance ......................................................................................................... pag. 6 ..................................
Figures ................................................................................. pag. 11 .......................................................................................
Electrical Diagran .......................................................................................................... pag. 14- .............................................. 15
THIS APPLIANCE HAS BEEN DESIGNED FOR NON PROFESSIONAL USE IN HOUSEHOLDS.
TECHNICAL MANUAL FOR THE INSTALLER
INFORMATION FOR THE INSTALLER
The installation, all regulations, changes and maintenance referred to in this part must only be carried out by qualiļ¬ed staļ¬€.
A wrong installation can cause damage to persons, animals or things which the manufacturer cannot be held responsible for.
The safety and automatic regulation devices on the appliances can only ever be changed by the manufacturer or by the
supplier which has been authorised to do so.
INSERTING THE HOB
When you have removed the various adjustable parts from their internal and external packaging, check that the hob is intact. If you are
in doubt do not use the appliance and contact the qualiļ¬ed staļ¬€.
The parts which make up the packaging ( polystyrene, bags, boxes, nails etc. ), are dangerous objects and must be kept out of
childrenā€™s reach.
Taking into consideration the speciļ¬c dimensions of the appliance (see table NĀ°1), make an opening in the work surface (see ļ¬gure 1)
using the measurements indicated in table NĀ°.1
The appliance must be classiļ¬ed in class 3 and thus it is subject to all the regulations indicated by the norms regarding these
appliances.
Table NĀ°.1
Hobs models
B3W0ā€¦
B3Y...
Hobs models
B3W0ā€¦
B3Y...
Min. Clearances
mm
Min. Clearances
mm
L1
520
L10
905
L2
40
L11
915
L3
40
W
925
L4
457
D
540
L5
610
B1 (*)
40
L6
330
B2 (*)
152
L7
925
B3 (*)
30
L8
20
B4 (*)
152
L9
162
(*) Note:
-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet.
-B2 and B4 are the min. clearance between the left/right side edge of the appliance and the side wall (if
present).
-B3 is the min. clearance betwe en the back edge of the appliance and the back wall.
ATTACHING THE HOTPLATE
To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with a special gasket. To apply
this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing strips along the edges of the opening in the bench
top and carefully overlap the strip end. (See Fig. 3). insert the hotplate into the bench top opening. With a screwdriver assemble the
brackets A to the hotplate bottom by means of the screws B. (See Fig. 4). Slide the hooks into position and secure them with the
screws.
Trim the part of the sealing strips which extend beyond the hotplate base
IMPORTANT INFORMATION CONCERNING THE INSTALLATION OF THE APPLIANCE
We inform the installer that this hob is of the Y type and thus it can be installed by itself, in an isolated position or inserted
between two kitchen units or between one kitchen unit and a wall. Furthermore the back wall and surrounding surfaces must
resist a temperature of 65 K.
To prevent the plastic layer which covers the kitchen unit from ungluing, the glue used to join the two surfaces together must
resist temperatures of up to 150 Ā°C
The installation of the appliance must be carried out according to the norms in force of the country concerned and the
appliance must be installed in a well ventilated place.
This appliance is not equipped with devices to remove the products of combustion. The appliance must therefore be
connected following the norms for installation mentioned above. Special attention must be paid to the information below
regarding aeration and ventilation of the premises.
VENTILATION OF THE PREMISES
To guarantee that the appliance works correctly it is necessary that the place where the appliance is installed is continuously ventilated.
The volume of the premises must not be less than 25 mĀ³ and the quantity of air needed must be based on the regular combustion of
gas and on the ventilation of the premises. The natural ļ¬‚ow of air will take place through permanent openings made in the wall of the
premises to be ventilated: these openings will be connected to the outside and must have a minimum section of 100 cmĀ² ( see Fig. 6 ).
These openings must be made in such a way that they cannot be obstructed.
POSITION AND VENTILATION
The cooking appliances that use gas must always remove the products of combustion via a hood linked to chimneys, chimney ļ¬‚ues or
via a direct connection to the outside ( see Fig. 6A ). If it is not possible to fit a hood it is possible to use a fan, ļ¬tted on the window or
facing directly outside, which operates when the appliance is in use. ( see Fig. 6B ). In this way the norms in force of the country
concerned regarding the ventilation of premises are strictly followed.
CONNECTING THE APPLIANCE TO THE GAS SUPPLY
Before connecting the appliance to the gas supply you ļ¬rst need to remove the plastic protective plug for the gas supply
which is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew it.
Then make sure that the details shown on the label on the lower part of the case are compatible with those of the gas supply .
A label on the last page of this manual and on the lower part of the case indicates the conditions for regulating the appliance:
type of gas and pressure used.
IMPORTANT: This appliance must be installed in accordance with the norms in force of the country concerned and it must
only be used in a well-ventilated place.
ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas cylindrical male in accordance
with the norms UNI-ISO 228-1. (Fig. 5)
ADAPTING TO DIFFERENT TYPES OF GAS
Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.
- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:
To change the nozzles of the burners use the following procedure:
Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the nozzles with those designed
for the new gas supply according to the information given in TABLE NĀ° 2 shown below.
ATTENTION: After carrying out the changes described above, the technician must put the label corresponding to the new gas
supply on the appliance to take the place of the old label. This label is found in the bag containing spare nozzles.
TABLE NĀ°2: Adapting to diļ¬€erent types of gas APPLIANCE CATEGORY: II2H3+
Burner
Pressure
Nozzle
Nominal Charge
Reduced Charge
Diameter
diameter
by-pass 1/100mm
mbar
1/100mm
g/h
l/h
Kw
kcal/h
kw
kcal/h
safety
20
77
-
95
1
860
0,3
258
27
Auxiliary
28 30-
50
73
-
1
860
0,3
258
27
37
50
71
-
1
860
0,3
258
27
Semi-
20
101
-
167
1,75
1505
0,44
378
31
Rap id
28
66
127
-
1,75
1505
0,44
378
31
37
66
125
-
1,75
1505
0,44
378
31
20
129
-
286
3
2580
0,75
645
42
Rapid
28
87
218
-
3
2580
0,75
645
42
37
87
214
-
3
2580
0,75
645
42
Dual
20
In 70
-
476
5
4300
0,48
413
In 34

Product specificaties

Merk: Bertazzoni
Categorie: Fornuis
Model: DB36600X-P92V

Heb je hulp nodig?

Als je hulp nodig hebt met Bertazzoni DB36600X-P92V stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Fornuis Bertazzoni

Bertazzoni

Bertazzoni PRO105I2EGIT Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO116L3EROT Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO64L1EROT Handleiding

14 November 2024
Bertazzoni

Bertazzoni MAS106L2ENET Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO106L2EBIT Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO106L3EBIT Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO115I3EART Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO106L2ENET Handleiding

14 November 2024
Bertazzoni

Bertazzoni PRO105I3ENET Handleiding

14 November 2024
Bertazzoni

Bertazzoni MAS64I1ENEC Handleiding

14 November 2024

Handleiding Fornuis

Nieuwste handleidingen voor Fornuis

Smeg

Smeg SR764BS Handleiding

21 November 2024
Panasonic

Panasonic KY-W648CLJPQ Handleiding

21 November 2024
Panasonic

Panasonic KY-R64ARLJPQ Handleiding

21 November 2024
AEG

AEG CCX1530ACW Handleiding

21 November 2024
AEG

AEG CCX1530ACM Handleiding

21 November 2024
AEG

AEG CCX1530ACB Handleiding

21 November 2024
Freggia

Freggia HCI32B Handleiding

21 November 2024
Freggia

Freggia HCI32W Handleiding

21 November 2024
Freggia

Freggia HCI64B Handleiding

21 November 2024
Freggia

Freggia HCI64W Handleiding

21 November 2024