BeamZ S1800 DMX 160.493 Handleiding

BeamZ Effect machine S1800 DMX 160.493

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor BeamZ S1800 DMX 160.493 (16 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
Ref. Nr. 160.493
S DMX 1800
INSTRUCTION MANUAL
GEBRUIKSAANWIJZING
BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
V1.1
- 2 -
- 3 -
ENGLISH
Warning:
- The smokemachine must be placed at least 100 cm away from inflammable materials such as curtains, books,
etc. Make sure that the housing cannot be touched by accident.
- For indoor use only.
- During installation, nobody should stand beneath the mounting area.
- Prior to the first use, have the unit checked by a qualified person.
- The unit contains voltage carrying parts. DO NOT open the smokemachine
- Never plug or unplug the unit with wet hands.
- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.
- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It
needs to be repaired by a qualified technician.
- Only connect this unit to an earthed mains outlet of 230Vac/50Hz .
- Always unplug the unit during a thunderstorm or when it is not in use.
- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let
the unit reach room temperature prior to use.
- When you unplug the unit from the mains always pull the plug, never the lead.
- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must
be fulfilled.
- Keep out of the reach of children.
Safety
Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can only be
replaced by an original replacement, supplied by Tronios. Be careful when filling the fluid tank. First of all, unplug the
mains lead! Then unscrew the cap on the tank and fill it by means of a funnel. Only use the original Beamz smoke fluid
which is environmental friendly and, if used correctly, leaves no residues. Do not obstruct the openings on top of the case
to guarantee a good ventilation. The heating element of the smoke machine generates heat which needs to be removed.
Donโ€™t put any objects on the smoke machine.
Installation and Use
Unpack the fog machine. Do not connect yet the net cable. Connect the lead of the manual control with the 3 pin plug at -
the rear of the smoke machine. Fill the fluid tank by means of a funnel. Plug the unit into a mains outlet. Thus the heating
element is automatically switched on. Depending on the room temperature, it takes about 6 minutes until the working
temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up. Push the switch once
and the smoke machine will produce a nice thick fog. Once the smoke machine has reached its working temperature (the
LED is lit) the smoke machine can produce continuously fog during max 1 After this period of time, the fog minute.
generator is cooled so much down that the thermostat switches off. Wait a few minutes until the working temperature is
reached again. It is recommended to produce smoke with small pauses in between so that the temperature is maintained
and the thermostat doesnโ€™t switch off. Use the smoke machine only when it is placed on the ground.
NOTE: Nozzle can be very HOT !!


Product specificaties

Merk: BeamZ
Categorie: Effect machine
Model: S1800 DMX 160.493

Heb je hulp nodig?

Als je hulp nodig hebt met BeamZ S1800 DMX 160.493 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Effect machine BeamZ

Handleiding Effect machine

Nieuwste handleidingen voor Effect machine